B-TEK Scales TensionLink WS Manual de usuario
Technical Manual
TensionLink WS
Wireless Crane Scale
V1.16
CONTENTS
1. PRECAUTIONS……………………………………………………………………..1
2. SPECIFICATION..…………………………………………………………………. 3
3. INTRODUCTION…………………………………………………………………... 4
4. KEYS DESCRIPTION……………………………………………………………..5
Key Board…………………………………………………………………………..5
Di play……………………………………………………………………………6
5. OPERATION OF indicator……………………………………………………… 7
5.1. Ba ic Operation…………………………………………………………... ...7
1. Power On /Off………………..………………………………………………7
2. Zero…………………………………………………………………………...7
3. Tare…………………………………………………………………………...7
4. Weighing Operation…………………………………………………………7
5.2. Accumulation…………………………………………………………………8
5.2.1. Manual Accumulation……...…………………….………………….8
5.2.2. Memory Recall……………...…………………….………………….8
5.2.3. Memory Clear………………………………………………………...8
5.3. Reading Lock……………………………………………………………….8
5.4 Change Weighing Unit…………………...………………………………….8
6. PARAMETERS…………………………………………………………………….10
7. CALIBRATION……………………………………………………………………..12
8. DRAWINGS ……………………………………….…….…….………………..14
9. CHANNEL…………………………………………………………………….16
10. DIMENSIONS ……………………………………….…….…….……………….17
Tension Link WS Series wireless crane scale Technical Manual
- 1 -
1. PRECAUTIONS
WARNING
DISCONNECT ALL POWER TO THIS UNIT
EFORE INSTALLING, CLEANING, OR
SERVICING. FAILURE TO DO SO COULD
RESULT IN ODILY HARM OR DAMAGE THE
UNIT.
CAUTION
Only qualified persons to service the instrument
efore connecting or disconnecting any components, remove the
power.
Failure to observe these precautions bodily harm or damage to or
destruction of the equipment.
Load the balance only in vertical travel direction.
Do not leave the controls while a load is suspended
Tension Link WS Series wireless crane scale Technical
- 2 -
Operate the scale at a safe speed
Never position the load over a person or any body part
Avoid extreme temperature.
Avoid un table power ource . Do not u e near large u er of electricity
uch a welding equipment or large motor .
Avoid high humidity that might cau e conden ation. Avoid direct contact
with water. Do not pray or immer e the cale in water.
Do not tack material on the cale when they are not in u e.
Never tand under the load, or injury / death may occur.
Read thi manual before operating or repairing thi equipment.
Follow the e in truction carefully.
Di connect the equipment from power ource before maintaining.
The weighing indicator i a preci ion electronic in trument, handle with
care.
Verify the local voltage and receptacle type are correct for the cale.
Only u e original adaptor, other may cau e damage to cale.
Avoid udden temperature change , and vibration.
Avoid heavy Radio Frequency noi e.
Keep the indicator clean
Tension Link WS Series wireless crane scale Technical
- 3 -
2. SPECIFICATION
Common Specifications:
Note: -TEK is currently stocking the 11K and 22K scales.
Please inquire with -TEK if other capacities are required.
Model Tension Link WS
(
wireless remote indic
ator
)
Di play 23mm/.9inch digit LCD di play with white
LED back light
Indicator Hou ing ABS Pla tic
Operating Temperature
0°C
-
40°C / 32°F
-
104°F
Re olution
1000d
--
5
0
00d
Key Pad 7 Key
Indicator Power AC Adaptor (12V/500mA)
Battery (
20
00mAh/1.2Vx
6
)
Interface
RS
-
232 Output (Optional)
Model
Tension Link W
S
(
scale)
Di play 23mm/.9inch digit LCD di play with white
LED back light
Scale Hou ing
aluminum
Operating Temperature
0°C
-
40°C / 32°F
-
104°F
Re
olution
1
000d
---
5000d
Key Pad 1 Key： on/off key
Scale Power AC Adaptor (9V/800mA)
Ni-MH Battery (1.2Vx3)
R
emoveable
3 AA batter
ie
Model
SH
-
W
S
-
1t
SH
-
W
S
-
3t
SH
-
W
S
-
5t
SH
-
W
S
-
10t
Capacity 2,200lb
1,000kg
10
,000
N
6,600lb
3,000kg
30,00
0
N
11,000lb
5,000kg
50,000
N
22,000lb
10,000kg
100,000
N
Division .5lb / 0.2kg
2N
2lb / 1kg
10N
5lb / 2kg
20
N
10lb / 5kg
50
N
Tension Link WS Series wireless crane scale Technical
- 4 -
3. INTRODUCTION
The Ten ion Link WS erie handheld indicator get fa t and accurate
weighing by wirele communication. It i u ed with the Ten ion Link WS
crane cale.
Handheld indicator can be connected to a printer or a PC.
Large LCD with white LED back light di play
Battery provide up to 40 hour of continue u e (without backlight).
Wirele communication di tance i up to 33 meter (100 feet).
Tension Link WS Series wireless crane scale Technical
- 5 -
4. KEYS DESCRIPTION
Key Board
Indicator Crane Scale
KEY
FUNCTION
Weighing
mode
Setting mode
Power On / Off
Tare function.
Change election
U ed to re et to Zero.
Enter
Lock/peak reading
M+
U ed to do accumulation, if
connected PC or printer, it will
end weighing data.
Move digit
UNIT
Change unit E cape etting mode
G/N
Change between Gro /NET Clear active digit
Tension Link WS Series wireless crane scale Technical
- 6 -
Di play
DISPLAY
FUNCTION
ZERO Zero di play indication
OZT / kg Unit indication
HI / OK / LO Check weighing indication
NET Net weight indication
STA LE Stable indication
M+ Accumulation indication
Wirele connection indication
Indication tatu of battery.
Tension Link WS Series wireless crane scale Technical
- 7 -
5. OPERATION of indicator
Initial Start-up
Warm-up time of 15 minute tabilize the mea ured value after witching on.
5.1. asic Operation
1. Power ON/OFF:
Switch on the balance by pre ing the key.
The di play i witched on and the elf-te t i tarted. To witch off, pre
the key again.
2. Zero
Set the di played weight to zero any time by pre ing key. Zero
hould be et before applying any load.
3. Tare
The tare weight of a container can be et by pre ing the button,
the net weight of the object i now di played.
Apply tare weight to the hook.
Pre key. Zero i di played, and tare weight i ubtracted.
Remove the container weight. Negative tare weight i now di played.
Only one tare value can be et.
To clear the tare value, remove the load and pre key. Zero i
di played, tare weight i cleared.
4. Weighing Operation
Rig the load with adequately load rated rigging equipment.
Slowly rai e the load to a afe level, wait few econd for a table
di play.
Read the re ult.
Avoid overloading. When di play how “
ol
” reduce the load or
unload.
Tension Link WS Series wireless crane scale Technical
- 8 -
5.2 Accumulation
Ten ion Link WS can do accumulation, it can ave 99 weighment of data.
5.2.1 Manual Accumulation
Accumulation Operation:
En ure di play i zero.
Place good , when get table, Pre M+ key.
Remove good from the hook, di play of Ten ion Link indicator,
Followed by the total tored value
Thi will only di play for 3 econd
5.2.2 Memory Recall
In the weighing mode, when di playing value i zero or le than 20d,
pre M+ key, di play of Ten ion Link indicator di play .
Total tored value will follow.
5.2.3 Memory Clear
In the weighing mode pre M+ key.
Di play of Ten ion Link indicator.
Total tored value will follow.
Pre G/N key, tored memory will be cleared.
Note: if you ee adder, it mean accumulation error, plea e make ure the
weight i more than 20d, or it will not perform accumulation.
5.3 Reading Lock or peak value
Read lock or peak value by pre ing key. pre thi key again to return
to normal di play.
Note: enable/di able thi function in parameter P4 HLD. (page 10)
When in peak/hold mode, peak/hold indication will turn on.
5.4 Change Weighing Unit
In normal di play, UNIT key will change weighing unit: kg / g / oz / lb / N.
Note: enable/di able the e unit in parameter F2 unt
0
100
N 001
100
N 001
100
N 001
100
Tabla de contenidos
Otros manuales de Escala de B-TEK Scales
B-TEK Scales
B-TEK Scales Super Sack Manual de usuario
B-TEK Scales
B-TEK Scales AquaShield Series Manual de usuario
B-TEK Scales
B-TEK Scales WorldWEIGH C200 Series Manual de usuario
B-TEK Scales
B-TEK Scales Above-ground Manual de usuario
B-TEK Scales
B-TEK Scales DuraShield Manual de usuario
B-TEK Scales
B-TEK Scales Skynet Instrucciones de instalación y mantenimiento
B-TEK Scales
B-TEK Scales WorldWEIGH C100 Series Manual de usuario
B-TEK Scales
B-TEK Scales AX200 Manual de usuario
B-TEK Scales
B-TEK Scales DD1010 Manual de usuario
B-TEK Scales
B-TEK Scales BT-BC Manual de usuario
