B-TEK Scales 4 Square Manual de usuario
4 Square
Clydesdale
Clydesdale Lift Deck
Workhorse
Drum Scale
RPS (Rocker Pin)
Models Include:
www.B-TEK.com 2020
Floor Scale Installation Manual
2
2020 www.B-TEK.com Floor Scale Installation Manual 3
Contents
Introduction Page 4
4 Square General Specs Page 5
Clydesdale Carbon General Specs Page 6
Clydesdale Stainless General Specs Page 7
Clydesdale Stainless Lift Deck General Specs Page 8
Workhorse Carbon General Specs Page 9
Drum Scale Carbon and Stainless General Specs General Specs Page 10
Rocker Pin Suspension (RPS) Carbon and Stainless General Specs Page 11
Installation Overview/Site Preperation Page 12
Pit Frame Installation Page 13
Unpacking Page 14
Assembling the Scale Page 15
Assembling the Scale - Workhorse Page 16
Assembling the Scale - Drum Page 16
Assembling the Scale - RPS Page 17
Anchoring the Scale - RPS Page 18
Opening and Cleaning - Lift Deck Page 19
Summing Board Connections Page 20
Floor Scale Wiring Diagram Page 21
Connecting the Indicator Page 22
Corner Adjustment and Calibration Page 22
Troubleshooting Page 23
Load Cell Replacement Page 24
Spare Parts Page 25
www.B-TEK.com 2020
Floor Scale Installation Manual
4
Introduction
This manual is meant as an installation guide for the B-TEK oor scale. This includes the following models:
4 Square 4’ X 4’ carbon steel oor scale
BT-FC carbon steel oor scale
BT-FS stainless steel oor scale
BT-LD stainless steel Lift Deck
BT-RP Rocker Pin Suspension oor scale
BT-FCHD Workhorse platform scale
BS-CS-DS carbon steel Drum scale
BS-SS-DS stainless steel Drum scale
The 4 Square model of oor scale is a 4’ X 4’ platform with a NTEP approved capacity of 5,000 lbs.
The Clydesdale series of carbon and stainless steel oor scale is available in standard platform sizes from 2’ X 2’ to 10’
X 8’, which are NTEP approved. Capacities range from 500 lbs up to 20,000 lbs for NTEP approved capacities. Custom
sizes and other capacities are available, contact the factory for more information.
The Clydesdale Stainless Steel Lift Deck is available in standard platform sizes from 3’ x 3’ - 4’ x 6’, which are NTEP ap-
proved. Capacities range from 2,500 to 5,000 lb. Custom sizes and other capacities are available, contact the factory for
more information.
The Rocker Pin Suspension series of carbon and stainless steel oor scale is available in standard platform sizes from 3’
x 3’ to 5’ x 7’, which are NTEP approved. Capacities range from 500 lbs to 10,000 lbs. Custom sizes and capacities are
available, contact factory for more information.
The Workhorse series of carbon steel scales is a heavy duty version platform scale with standard size of 4’ X 4’ to 12’ X
10’. Capacities range from 20,000 lbs up to 40,000 lbs. The scale is NTEP approved. Custom sizes and other
capacities are available, contact the factory for more information.
The Drum scale series is available in both carbon and stainless steel versions. Standard platform sizes are 24” X 24”,
30” X 30”, 36” X 36” and 48” X 48”. Standard capacities are 1,000 lbs and 2,500 lbs, which are NTEP approved. Optional
accessories include integral and detachable access ramps, indicator column and portability kits. Custom sizes and other
capacities are available, contact the factory for more information.
No physical or electrical changes / alterations may be made to the scale during installation or use, which may void the
warranty. This includes removal, addition or modication of any steel or components, as well as electrical or program
related items.
Prior to installation it is the customer’s responsibility to verify that the equipment meets the requirements of the
application. Do not begin installation if this is unknown. It is the customer’s responsibility to ensure that the scale
equipment is operated within the manufacturer’s specications.
Any repairs must be performed by B-TEK Scales authorized service technicians.
Failure to comply with this policy voids all implied and/or written warranties.
2020 www.B-TEK.com Floor Scale Installation Manual 5
4 Square Carbon Steel Floor Scale
General Specications:
Certicate of Conformance: 94-092A4
Type: Above ground or pit
Scale Capacity: 5,000 lbs.
End Load Capacity: 150%
Scale Height: 3-1/2” nominal, adjustable
Available Sizes: 4’ x 4’
Weighbridge: Laser cut 3/16” carbon steel tread plate decking with structural channel sub-structure
Deck: Top access junction box, threaded lifting eye bolt hole in platform center
Paint System: Alkyd Enamel
Load Cell: (4) 4,000 lb., plated alloy steel, 350 Ohms, 3.0mV/V cells
Leveling Foot: B-TEK Level-Flex rubber feet - 2.5” diameter base
Junction Box: NEMA 4 berglass reinforced plastic (FRP) box with signal trim summing board
Accessories: Ramps, bump-guard, oor mounting plates
Warranty: 1-Year on weighbridge steel structure, load cells, junction box and summing board
www.B-TEK.com 2020
Floor Scale Installation Manual
6
Clydesdale Carbon Steel Floor Scale
General Specications:
Certicate of Conformance: 94-092A4
Type: Above ground or pit
Scale Capacity: 500 - 20,000 lbs. - NTEP Approved Capacities
End Load Capacity: 80% for 2.5K capacity
100% for 5K to 20K capacities
Scale Height: 4-3/8” nominal (2.5K - 10K-SE) adjustable
5-3/8” nominal (10K-LE - 20K) adjustable
Available Sizes: 2’ x 2’ - 8’ x 10’ - NTEP Approved Sizes
Any custom size platform available - 18” x 18” to 10’ x 12’
Weighbridge: Laser cut 1/4” carbon steel tread plate with formed channel sub-structure (2.5K - 10K-SE)
Laser cut 3/8” carbon steel tread plate with structural channel sub-structure (10K-LE & 20K)
Deck: Top access junction box, leveling foot adjustment holes.
Threaded lifting eye bolt holes: 5/8”-11 eyebolt
Paint System: Alkyd Enamel
Load Cell: Plated alloy steel, 350 Ohms, 3.0mV/V FM Approved
500lb capacity: (4) 250lb. cells
1K capacity: (4) 500 lb. cells
2.5K capacity: (4) 1,000 lb. cells
5K capacity: (4) 2,500 lb. cells by request in Clydesdale
5K capacity: (4) 4,000 lb. cells standard in Clydesdale
10K SE capacity: (4) 5,000 lb. cells (small envelope)
10K LE capacity: (4) 5,000 lb. cells (large envelope)
20K capacity: (4) 10,000 lb. cells
Optional Stainless Steel cells are available for any capacity listed above
Leveling foot: B-TEK stainless steel ball encapsulated foot
Junction Box: NEMA 4 berglass reinforced plastic (FRP) with signal trim summing board
Warranty: 3-Years on weighbridge steel structure,
2-Years on load cells, junction box and summing board
2020 www.B-TEK.com Floor Scale Installation Manual 7
Clydesdale Stainless Steel Floor Scale
General Specications:
Certicate of Conformance: 94-092A4
Type: Above ground or pit
Scale Capacity: 2,500 - 10,000 lbs.
End Load Capacity: 80% for 2.5K capacity
100% for 5K to 20K capacities
Scale Height: 4-3/8” nominal (2.5K - 10K-SE) adjustable
Available Sizes: 2’ x 2’ - 5’ x 7’ - Custom sizes upon request
Weighbridge: Laser cut 1/4” 304 stainless steel SMOOTH plate with structural channel sub-structure
Deck: Side access junction box, threaded lifting eye bolt holes
Finish: All exposed surface are media blasted to a clean, consistent appearance
Load Cell: Stainless steel (IP67), 350 Ohms, 3.0mV/V FM Approved
2.5K capacity: (4) 1,000 lb. cells
5K capacity: (4) 2,500 lb. cells by request in Clydesdale SS
5K capacity: (4) 4,000 lb. cells standard in Clydesdale SS
10K capacity: (4) 5,000 lb. cells
Optional hermetically sealed (IP68) cells are available for any capacity listed above
Leveling foot: B-TEK stainless steel ball encapsulated foot - 2.5” diameter base
Junction Box: NEMA 4 box with signal trim summing board
Warranty: 3-Years on weighbridge steel structure
2-Years on load cells, junction box and summing board
www.B-TEK.com 2020
Floor Scale Installation Manual
8
Clydesdale Stainless Steel Lift Deck Floor Scale
General Specications:
Certicate of Conformance: 94-092A4
Type: Above ground or pit
Scale Capacity: 2,500 - 5,000 lb
End Load Capacity: 80% for 2.5K capacity
100% for 5K capacity
Scale Height: 4-3/8" nominal height, adjustable
Available Sizes: 3' x 3' - 4' x 6' - Custom sizes upon request
Weighbridge: 1/4" 304 stainless steel SMOOTH plate with structural tube frame
Deck: Lifting handles on top plate with dual gas shocks to aid in raising
Finish: All exposed surfaces are media blasted to a clean, consistent appearance
Load Cell: Stainless steel (IP67), 350 Ohms, 3.0mV/V
2.5K capacity: (4) 1,000 lb
5K capacity: (4) 2,500 lb cells by request in Clydesdale
5K capacity: (4) 4,000 lb cells standard in Clydesdale
Optional hermetically sealed (IP68) cells are available for any capacity listed
above
Leveling foot: B-TEK stainless steel ball encapsulated foot - 2.5" diameter base
Junction Box: Side access NEMA 4 junction box with signal trim summing board
Warranty: 3-Years on weighbridge steel structure
2-Years on load cells, junction box, and summing board
2020 www.B-TEK.com Floor Scale Installation Manual 9
Workhorse Carbon Steel Heavy Duty
General Specications:
Certicate of Conformance: 18-061
Type: Above ground or pit
Scale Capacity: 20,0000 x 5lb
30,000 x 10lb
40,000 x 10lb
End Load Capacity: 100% for 20K and 40K capacities
66% for 30K capacity
Scale Height: 9” to 14” depending on platform size and capacity
Available Sizes: 4’ x 4’ - 12’ x 10’ - Custom sizes upon request
Weighbridge: 3/8” carbon steel SMOOTH or TREAD plate with WF-Beam sub-structure
Deck: Welded deck plate standard - Bolted deck plate optional
Paint System: Alkyd Enamel
Load Cell: B-TEK LCMT mount assembly bolted to WF-Beam sub-structure
20K capacity: (4) 10,000 lb., plated alloy steel, 350 Ohms, 3.0mV/V
30K capacity: (4) 10,000 lb., plated alloy steel, 350 Ohms, 3.0mV/V
40K capacity: (4) 20,000 lb., plated alloy steel, 350 Ohms, 3.0mV/V
Junction Box: Externally mounted NEMA 4X stainless steel junction box with signal trim summing board
Top access junction box available by request or standard when platform is installed in pit
Warranty: 5-Years on weighbridge steel structure
2-Years on load cells, junction box and summing board
www.B-TEK.com 2020
Floor Scale Installation Manual
10
Drum Scale Carbon & Stainless Steel
General Specications:
Certicate of Conformance: 94-092A4
Type: Low prole above ground
Scale Capacity: 1,000 & 2,500 lbs.
Scale Height: 1-1/2” nominal deck height
Available Sizes: 2’ x 2’ - 4’ x 4’ - Custom sizes upon request
Weighbridge: 1/4” carbon steel tread plate deck with live side rail design
1/4” 304 stainless steel SMOOTH deck with live side rail design
Deck: Side access FRP junction box, leveling foot adjustment holes in side rails
Paint System/Finish: Carbon: Alkyd Enamel
Stainless: All exposed surfaces are media blasted to a clean, consistent appearance
Load Cell: Plated alloy steel, 350 Ohms, 3.0mV/V
1K capacity: (4) 1,000 lb.
2.5K capacity: (4) 2,500 lb.
Stainless steel (IP67), 350 Ohms, 3.0mV/V
1K capacity: (4) 1,000 lb.
2.5K capacity: (4) 2,500 lb.
Junction Box: Carbon: NEMA 4 berglass reinforced plastic (FRP) with signal trim summing board
Stainless: NEMA 4 with signal trim summing board
Warranty: 3-Years on weighbridge steel structure
2-Years on load cells, junction box and summing board
Este manual sirve para los siguientes modelos
13
Tabla de contenidos
Otros manuales de Escala de B-TEK Scales
B-TEK Scales
B-TEK Scales Super Sack Manual de usuario
B-TEK Scales
B-TEK Scales Skynet Instrucciones de instalación y mantenimiento
B-TEK Scales
B-TEK Scales AX200 Manual de usuario
B-TEK Scales
B-TEK Scales DuraShield Manual de usuario
B-TEK Scales
B-TEK Scales WorldWEIGH C100 Series Manual de usuario
B-TEK Scales
B-TEK Scales Centurion-DT Manual de usuario
B-TEK Scales
B-TEK Scales AquaShield Series Manual de usuario
B-TEK Scales
B-TEK Scales Above-ground Manual de usuario
B-TEK Scales
B-TEK Scales BT-BC Manual de usuario
B-TEK Scales
B-TEK Scales TensionLink WS Manual de usuario
