Avtech AVT1105XT Manual de usuario

858Z

t1105xt_V1.0

IR Bullet Camera User Manual

Please use this camera with a DVR which supports HD video recording.

Please read the instructions thoroughly before using the product.

To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.

Only operate this apparatus from the type of power source indicated on the label.

The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of

such damages.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

This exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

ROHS Announcement

All lead-free products offered by the company comply with the requirements of the European law on the Restriction

of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly

“lead-free” and without the hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected

separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do

not dispose of these products as unsorted municipal waste.

CE Mark

This apparatus is manufactured to comply with the radio interference.

The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or

remove any content in this manual at any time.

FEATURES

1. 1/2.7” CMOS Sensor with 1080P video output

2. Low light sensitivity of 0.1 Lux / F1.8, 0Lux (IR LED ON)

3. DWDR to increase image recognizability in overexposure and dark areas

4. External alarm I/O device connection

5. Day and night 24-hour surveillance with IR effective distance up to 25 meters

6. IP66 for weather-proof application

7. Camera parameters adjustable when used with HD CCTV DVR

PACKAGE CONTENT

IR camera User manual Wrench Accessory

DIMENSIONS*

*Dimensional Tolerance: ± 5mm

SPECIFICATIONS*

Pick-up Element 1/ 2.7” CMOS image sensor

Number of Pixels 1936(H) x 1096(V)

Video Frame Rate 1080P@30fps / 1080P@25fps

Min. Illumination 0.1 Lux / F1.8, 0 Lux (IR LED ON)

S/N Ratio More than 48dB (AGC OFF)

Shutter Speed 1/30 (1/25) sec ~ 1/50000 sec

Lens f3.6mm / F1.8 f2.8mm / F1.8

Lens Angle 89° (Horizontal) / 46° (Vertical) /

108° (Diagonal)

118° (Horizontal) / 65° (Vertical) /

136° (Diagonal)

IR LED 2 units

IR Effective Distance Up to 25 meters

IR Shift YES

Day & Night Mode YES

Noise Reduction YES

IRIS Mode AES

White Balance AUTO / INDOOR / OUTDOOR / MANUAL

AGC Adjustable

Sharpness Adjustable

Flickerless 50HZ / 60HZ / OFF

BLC Adjustable

DWDR YES

External Alarm I/O YES (1 in / 1 out)

IP Rating IP66

Operating Temperature -40℃~ 40℃

Operating Humidity 90% or less relative humidity

Power Source (±10%) DC12V / 0.5A

Current Consumption (±10%) 95mA (IR lED OFF); 265mA (IR LED ON)

Net Weight (kg) 0.36

* The specifications are subject to change without notice.

INSTALLATION

Step1: Find the wrench supplied in the sales package, and loosen the screw as indicated below to loosen

the joint lock of the bracket.

Note: for lock, and for unlock.

Step2: Locate where to install this camera, and fasten the bracket to the ceiling or wall.

Then, adjust the viewing angle of the camera, and fasten the screw to secure the joint lock of the

bracket.

Note: for lock, and for unlock.

CONNECTION

1. DC12V Input Terminal

Connect the power terminal of the camera to a DC 12V regulated power supply.

Note: Please use the correct power adaptor, DC12V (regulated), to operate this unit. The power

tolerance of this unit is DC12V ± 10%. Over maximum DC 12V power input will damage this

unit.

2. Video Output Connector (VIDEO OUT)

Connect the camera video output to the video input of a DVR with 75Ωcoaxial cable.

Note: To ensure the camera has sufficient protection against moisture, an extra waterproof

measure, such as by using an insulating tape, must be used to cover the power and video

connectors after connection.

WIRE INDICATION FOR ALARM CONNECTION

COLOR FUNCTION COLOR FUNCTION COLOR FUNCTION

Yellow ALARM IN Blue ALARM OUT Black GND

* Please use with a 3V relay.

CAMERA PARAMETERS

This camera series has its own configuration menu.

On the DVR live view, click the channel which connects this camera to display in the full screen mode, and

select on the bottom left side of the screen to show the PTZ control panel.

Click to show the camera menu and you can move among sub-menus:

/ Move among sub-menus.

/ Change settings.

Call the camera parameters menu or enter the currently-selected item.

MENU DESCRIPTION

EXPOSURE SHUTTER AUTO Automatically adjust the shutter speed for exposure

based on the current environment.

1/30

1/100

1/250

1/500

1/1000

1/2000

1/4000

1/5000

1/50000

Manually choose the shutter speed you need for

exposure.

AGC 0 ~ 65535 Set the level of Auto Gain Control to detect and

enhance the image signals when the light condition is

poor.

The higher the value, the stronger the signals will be

enhanced, and the more noise the image will get.

BRIGHTNESS 0 ~ 255 Set the level to compensate the brightness of the image

if needed.

The more the value, the brighter the image will be.

HSBLC ON / OFF HSBLC (highlight suppression back light

compensation) is used to suppress strong backlight for

clearer images. A grey mask will be covered on the

source of the strong light.

WHITE BAL AWB Automatically adjust the white balance based on the

surrounding environment.

INDOOR Selected when the camera is installed in the indoor

environment.

OUTDOOR Selected when the camera is installed in the outdoor

environment.

MANUAL R GAIN 0 ~ 255

Manually adjust the R / G / B gain parameters.

G GAIN 0 ~ 255

B GAIN 0 ~ 255

MENU DESCRIPTION

DAYNIGHT EXT ALS IN

DELAY

0 ~ 255 Set the delay time in second after which the day and night

switch is made.

This is used for the environment where the light condition

may change suddenly and usually last for a short time, for

example, the entrance of a parking lot. It may cause the

day & night mode switching constantly and damage the

camera.

With this function, the camera will delay the mode switch

at night since the light change is temporary and

unnecessary to pay attention.

B&W Always keep the day and night mode to night mode.

OFF Always keep the day and night mode to day mode.

IMAGE NR AUTO Automatically reduce noise in the image based on the

current environment.

MANUAL STRENGTH Set the level to enable noise reduction.

OFF Choose to disable this function.

DWDR ON / OFF DWDR is used to increase image recognizability in

overexposure and dark areas.

Choose ON / OFF enable / disable this function.

PRIVACY OFF Disable this function.

ON COLOR Choose the color for the area selected in MASK SEL.

You can choose NO COLOR to disable this function,

MOSAIC for mosaic display, or 1~ 14 for different

colors.

MASK SEL Select the area you want to mask. Up to four areas could

be configured.

MASK DRAW Set the size of the masked area:

1. Click



and change the

size by clicking , , 

and .

2. Click



again and

change the size by clicking

, , and .

3. Click again to finish and exit.

MOTION OFF Choose to disable motion detection.

ON (BORDER) AREA SEL Select the area you want to detect. Up to four areas could

be configured.

The area will be framed and flashed when a motion event

occurs.

POSITION Choose ON to show where the area selected in AREA

SEL is and set the size of the area:

1. Click



and change the

size by clicking , , 

and .

2. Click



again and

change the size by clicking

, , and .

3. Click



again to finish and exit.

SENSITIVITY Set the sensitivity for motion detection.

The larger the value, the more sensitive the detection.

COLOR Choose the color for the selected area to show when a

motion event occurs: RED / GREEN / BLUE / WHITE.

TRANS Choose the transparent level for the selected area when

a motion event occurs.

The larger the value, the more transparent the area.

MENU DESCRIPTION

IMAGE MOTION ON (SOLID) AREA SEL Click



to set the area you want to detect. Up to four

areas could be configured.

The area will be masked and flashed when a motion

event occurs.

POSITION Choose ON to show where the area selected in AREA

SEL is and set the size of the area:

1. Click



and change the

size by clicking , , 

and .

2. Click



again and

change the size by clicking

, , and .

3. Click



again to finish and exit.

SENSITIVITY Set the sensitivity for motion detection from 1 to 24.

The larger the value, the more sensitive the detection.

COLOR Choose the color for the selected area to show when a

motion event occurs: RED / GREEN / BLUE / WHITE.

TRANS Choose the transparent level for the selected area from 1

~ 8when a motion event occurs.

The larger the value, the more transparent the area.

LSC ON / OFF Enable (ON) or disable (OFF) Lens Shading Correction

to correct the phenomenon of vignetting when the focal

length is short.

MIRROR OFF / ON Enable (ON) to turn the images horizontally based on

your installation situation when necessary.

BPC DYNAMIC BPC (bad point compensation) is used to compensate

dead pixels in the image.

Click to further configure DYNAMIC /

STATIC W (white) / STATIC B (black).

STATIC W

STATIC B

PICT ADJ SHARPNESS 0 ~ 15 Set the level of sharpness to enhance the clarity of image

detail by adjusting the aperture and sharpening the

edges.

The more the value, the sharper the image will be.

CB GAIN 0 ~ 255 Adjust the blue value.

CR GAIN 0 ~ 255 Adjust the red value.

BLACK LEVEL -128 ~ 127 Adjust the level of black.

GAMMA 0.4 / 0.45 / 0.5 Choose for gamma correction.

SYSTEM CAM TITLE OFF / ON Set the camera ID.

LANGUAGE ENG / CHI S Select the language of the menu: English / Simplified

Chinese.

FORMAT NTSC / PAL Choose to change the video system format if needed.

EXIT SAVE&END Save all the changes made and exit.

NOT SAVE Quit without saving.

RESET Reset to factory default values.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Avtech

Avtech

Avtech avm420s Manual de usuario

Avtech

Avtech DGC1105A Manual de usuario

Avtech

Avtech AVM357A Manual de usuario

Avtech

Avtech KPC132 Manual de usuario

Avtech

Avtech AVP325 Manual de usuario

Avtech

Avtech YGN2003 Manual de usuario

Avtech

Avtech AVN211 Manual de usuario

Avtech

Avtech DG103 Instrucciones de funcionamiento

Avtech

Avtech DGM1104QS Manual de usuario

Avtech

Avtech DGC1104XFT Manual de usuario

Avtech

Avtech DG104A Manual de usuario

Avtech

Avtech AVN304 Manual de usuario

Avtech

Avtech AVT543 Manual de usuario

Avtech

Avtech AVI321 Manual de usuario

Avtech

Avtech DGC5205TSE Manual de usuario

Avtech

Avtech AVN222 Manual de usuario

Avtech

Avtech Push Video AVN701 Manual de usuario

Avtech

Avtech KPC131 Manual de usuario

Avtech

Avtech AVI 201 Manual de usuario

Avtech

Avtech avt450a Manual de usuario

Avtech

Avtech DG206A Manual de usuario

Avtech

Avtech AVM328A Manual

Avtech

Avtech DGC5446SE Manual de usuario

Avtech

Avtech DG206 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario