AVIRE DCP Manual de usuario
1
DCP
Digital Communication Platform
Installation Guide
Ref No MU7756XAV10A-AU
Part numbers:
3G DCP (RS232): AC-3CM10-620-F-20-000
4G Single SIM card (RS232): AC-4CM10-620-F-20-000
4G Dual SIM card (RS232): AC-4CM10-820-F-20-000
PRODUCT DESCRIPTION
The Digital Communications Platform (DCP) provides an information gateway between
all compatible connected Avire devices in the lift shaft and our online monitoring
platform the Avire Hub. The product is installed as a stand-alone device and doesn’t
require connection to the controller panel.
Dual SIM card DCP version only: A dual SIM card version allows switching from one SIM
to another in case the connection is lost. The dual SIM card version also allows the use
of one SIM card for voice and the other one for data only.
In the Box
+ 4G DCP (either single or dual version)
OR 3G DCP
+ Antenna
+ P-5 H-2V connector (x1)
+ P-3.5 H-4V connector (x1)
+ P-10 H-2V connector (x1)
+ Grey clamp (x2)
+ Manual
Not Included
+ Screwdriver
+ SIM card/s
2
ELEVATOR SAFETY
Please follow all Health and Safety rules and take all necessary precautions before
and during installation. This device must be installed by qualied personnel and
always in a restricted area where only such personnel have access.
SETTING UP THE DCP
Avire SIM cards come activated and ready to be installed. If a non-Avire SIM card is
used, please make sure that the SIM card is activated and unlocked.
3. Connect the antenna on the DCP to J2 and
ensure it is completely tightened.
NOTE: Only use antennas authorised by Avire.
6. Check the signal strength by using the built-in
network signal strength scanner. To use the signal
scanner function:
+Turn SW1 dipswitch 1 to ON (check dipswitch 4 is
also ON)
Please refer to pages 13 and 14 for the full picture
and connector information
1. Open the DCP with a PZ1 screwdriver.
2. Depending on the version of DCP insert SIM(s) into the J4, pushing the SIM(s) until it
(they) click(s). The Dual SIM card version will still work with only 1 SIM installed.
SIM0
SIM1
J4
J2
J3
J4
SIM0
Single SIM card
Dual SIM card
SW1
4. Connect the battery to J3.
5. Wait for the LED lights to turn on.
Once the LED’s turn on, the SIM card
will begin to register with the network
which can take 2-5mins. Having
allowed time for the SIM to register,
check the SIM LED to make sure it is
green or amber (check step 10). If it’s
ashing red check it’s been inserted
correctly and then unlock the SIM
card using instructions on page 4.
3
+LEDs on the front of the DCP unit will show the network signal level
+
+
+
+
+
+
+
+
+
+
You can check the status of the power supply, battery, connection, coverage or
Phone Line (SLIC) at any time by referring to the LED Indicators (page 15).
7. With the power supply turned o, connect power 230VAC to J6 using the 3pin
connector supplied with the unit.
Note: The signal scanner will
indicate the best location for the
device to receive signal, Network
coverage will vary based on local
conditions.
+Once nished turn SW1 dipswitch 1 back to OFF.
Neutral
Live
SW1
J6
4
8. Clamp the power cable using the grey clamp provided inside the box.
9. Place the lid back on the top of the DCP and fasten the lid with the screw.
10. Turn on the power to the DCP. The RUN LED on the DCP should change colour
from ashing amber to ashing green when the mains power connection is made.
If you see any other colour, please consult the LED Indication list on page 14.
RUN LED ashes green Power supply is OK
BAT LED is always on Battery is OK
SIM LED is green or amber Device is connected to the network
Coverage LED is green or amber Good coverage
SLIC LED is green Device is in standby
J6
11. To x the device in position, drill two holes in the wall and insert the plugs and
screws provided with the device. Hang the DCP on these two points using the tear-
shaped holes at the back box of the DCP (mid points of holes are 105mm apart).
12. If a non-Avire SIM card is used, APN settings must be set prior to conguring it on
the Avire Hub; please refer to “Setting Parameters on non-Avire SIM cards” (page
6). If the SIM LED is ashing red, please see “SIM Card unlocking” (see page 5).
5
SIM CARD UNLOCKING
Important Note: An Avire SIM card doesn’t have a SIM PIN code; if the SIM LED is
ashing red, please make sure that the SIM card has been inserted correctly. The SIM
PIN code for other network providers may vary and it can usually be
found on the outer plastic case of the SIM card.
OPTION 1
Disable the blocking PIN code using a conventional mobile phone. Plug the SIM into a
dierent mobile device and delete SIM PIN code in the device settings.
OPTION 2
You can program the PIN code of the SIM card into the DCP using an analogue phone
plugged into to the J1A or J9 connection (please see page 13 for more details).
Single SIM card version:
Enter DCP conguration mode: wait for DCP voice command
Enter SIM card PIN parameter:
xxxx is the SIM PIN code given by the service provider for SIM0.
Dual SIM card version:
Enter DCP conguration mode: wait for DCP voice command
Enter SIM card PIN parameter:
xxxx is the SIM PIN code given by the service provider for SIM0
yyyy is the SIM PIN code for SIM1 (if installed and required).
Example if only 1 SIM PIN code is required:
If SIM0 PIN is needed - *1# xxxx#
If SIM1 PIN is needed please remove PIN code from SIM1 or install SIM into SIM0 port.
At this point, the SIM card LED (middle LED) will stop ashing red. If it does not, make
sure the SIM is correctly inserted and you have entered the correct PIN.
OPTION 3
You can remotely enter SIM PIN code into DCP by texting:
P1234, P090 xxxx yyyy
This option can only be used if DCP is already connected (if one of the two SIMs is
active).
Important Note: Check ADDITIONAL INFORMATION FOR PROGRAMMING THE DCP
on page 12 for more information.
6
SETTING PARAMETERS ON NON AVIRE SIMS
OPTION 1
Super settings allow quick and easy conguration of APN settings, depending on the
country and network provider. Congure settings for the DCP based on the tables
below.
Example:
Digit 1 0 1-6 7 8
Continent Default Europe Americas Australasia
Digit 1 Digit 2 Digit 3 Digit 4
Continent SIM0 Network Type of connection SIM1 Network
Digit 2 & 4 Network Country
0default default
1AvireSim -
2Telstra AUS
3Optus AUS
4Vodafone AUS
5Spark NZ
62 degrees NZ
7Vodafone NZ
8- -
9- -
Digit 3 0 1 2 3
Type Transparent Gateway Avire Hub P100 P100 + Avire Hub
The Digital Communications Platform comes pre-congured with factory settings of 0000 (this
conguration doesn’t specify any use case or country).
Digit 1 Digit 2 Digit 3 Digit 4
Country SIM0 Network Type of
Connection
SIM1 Network
Example
Single Sim 8 = (Australia) 2 = (Telstra) 1 = (Avire HUB) 0 = (No SIM)
Dual Sim 8 = (Australia) 2 = (Telstra) 1 = (Avire HUB) 3 = (Optus)
7
Once all digits are selected, the text
needs to be sent to the SIM card
telephone number along with the
PIN code and command. Response
should show:
0
0
OPTION 2
If super settings are not used, then APN settings need to be set up manually:
Command Description Parameters
P060 (P zero six zero) SIM0 congurations APN name ;APN username ; APN password*
P061 (P zero six one) SIM1 congurations APN name ;APN username ; APN password*
P063 (P zero six three) Type of connection Shared by both SIM cards
* Separated by “;”
These parameters must be congured by sending an SMS to the SIM card number.
Examples for various regional providers are shown below:
Carrier APN name APN username APN password
Vodafone AUS live.vodafone.com (blank) (blank)
Telstra AUS telstra.iph (blank) (blank)
Spark NZ internet (blank) (blank)
Other APN settings are available on the web and can be easily found online. If an APN
is incorrect for the provider or is not set up correctly, the DCP will not check into the
Avire HUB.
Important Note: The default PIN code for DCP is always 1234.
If either the APN username and/or APN password are (blank) and the DCP is congured
to be used with the Avire Hub, then the text message will be (example is for Vodafone
AUS):
Pin1234, P060 live.vodafone.com, P063 1
Example for dual SIM card version with SIM cards from Vodafone AUS (SIM0) and
Telstra AUS (SIM1):
Pin1234, P060 live.vodafone.com, P061 telstra.iph, P063 1
P063 0 1 2 3
Type Transparent Gateway Avire Hub P100 P100 + Avire Hub
If everything is congured correctly you will receive a
text within a few minutes:
8
Obtaining the CCID number
AVIRE SIM CARDS
Avire SIM cards come unlocked to be used with our products
immediately after plugging them in and setting correct Super settings.
You will need to know the CCID number to add this information to the
Avire Hub.
The CCID Number is shown on the back of the SIM card and also on the outer plastic
case of the SIM card (highlighted in red on the picture below).
Important Note: CCID number consists of 19 digits.
NON-AVIRE SIM CARDS
It is also possible to retrieve the CCID number by sending a SMS command to a SIM
card telephone number; the command needs to be separated by a comma as shown
below:
Pin1234, P005?
You will receive a text with the CCID number back within a few minutes; in this example,
the number shown after “P005=” is the CCID number of this SIM card.
Important note: Example CCID number is highlighted in red on picture above.
You will need to retrieve the CCID number when the DCP installation is set up on the
Avire Hub online platform. Please ensure that the person conguring the DCP on the
Avire Hub has both the CCID and detail relating to location of the DCP to ensure proper
setup.
9
AVIRE HUB
Please contact your local sales oce for access to the Avire Hub.
The link to the Avire Hub is http://avirehub.avire-global.com
To view installation tutorial videos please go to the “Help” section of the Avire Hub.
Click on “Installations” in the menu on the side
and then on “Buildings”. Inside of “Buildings” tab
click on “Create Building”
Enter information relevant to your installation in General data
10
On the other side of the page please enter the number of elevator groups you have in
this installation and how many elevators you have in each group. As an example, if this
is a simplex installation the number of elevator groups will be “1” and the number of
elevators will also be “1”. If it’s a duplex installation it will be “1” and “2” respectively.
You can also edit the group names to easily identify installations. Once all information
is entered click “Next”.
In the new page, you should be able to see Groups and Elevators. Click on “Add
Gateway” under “Gateway” tab and select “DCP 4G”. A pop up window will appear
where you can enter the SIM information (Note: Avire SIMs are (+31), but this doesn’t
aect costs). Enter all required information and then click “Apply”.
Note: The Background Call Period is the frequency of test checks and 72hrs is the
maximum period as per guidance from standards.
Note: if you are
installing a 3G DCP
please select DCP in
the menu
Otros manuales para DCP
3
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Sistema de conferencias de AVIRE
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
