AVIRE DCP Manual de usuario
1
DCP
Digital Communication Platform
Installation Guide
Ref No MC-xCM10 850 ML Version 4
In the Box
+ 2G or 3G DCP
+ Antenna
+ P-5 H-2V connector (x1)
+ P-3.5 H-4V connector (x1)
+ P-10 H-2V connector (x1)
+ Grey clamp (x2)
+ Manual
+ Wall plugs (x2)
+ Screws (x2)
Not Included
+ Screwdriver
+ SIM card
PRODUCT DESCRIPTION
The Digital Communication Platform (DCP) provides an information gateway between
all compatible connected Avire devices in the lift shaft and our online monitoring
platform the Avire Hub. The product is installed as a stand-alone device and doesn’t
require connection to the controller panel.
2G (R2S32): MC-2CM10-100-F-20-000
3G (RS232): MC-3CM10-100-F-20-000
2G (RS422/485): MC-2CM10-100-F-40-000
3G (RS422/485): MC-3CM10-100-F-40-000
*Congure your DCP using the Avire App
2
ELEVATOR SAFETY
Please follow all Health and Safety rules & take all necessary precautions before and
during installation.
SETTING UP THE DCP
Avire SIM cards come activated and ready to be installed. If a non-Avire SIM card is
used, please make sure that the SIM card is activated and unlocked.
3. Connect the antenna on the DCP to J2 and
ensure it is completely tightened.
NOTE: Only use antennas authorised by Avire.
4. Connect the battery to J3.
5. Wait for the LED lights to turn on.
Check the SIM LED to make sure it is
green or amber (check step 10). If it’s
ashing red check it’s been inserted
correctly and then unlock the SIM
card using instructions on page 5.
6. Check the signal strength by using the built-in
network signal strength scanner. To use the signal
scanner function:
+Turn SW1 dipswitch 1 to ON (check dipswitch 4 is
also ON)
Please refer to pages 13 and 14 for the full picture
and connector information
1. Open the DCP with a PZ1 screwdriver.
2. Insert SIM into J4, pushing the SIM until it clicks.
SIM0
J2
J3
SW1
3
+LEDs on the front of the DCP unit will show the network signal level
+
+
+
+
+
+
+
+
+
+
You can check the status of the power supply, battery, connection, coverage or
Phone Line (SLIC) at any time by referring to the LED Indicators (page 15).
7. Connect the power supply 230VAC to J6, using the 3pin connector supplied with
the unit.
Note: The signal scanner will
indicate the best location for the
device to receive signal, Network
coverage will vary based on local
conditions.
+Once nished turn SW1 dipswitch 1 back to OFF.
Neutral
Live
SW1
J6
4
8. Clamp the power cable using the grey clamp provided inside the box.
9. Place the lid back on the top of the DCP and fasten the lid with the screw.
10. Turn on the power to the DCP. The RUN LED on the DCP should change colour
from ashing amber to ashing green when the mains power connection is made.
If you see any other colour, please consult the LED Indication list on page 15.
RUN LED ashes green Power supply is OK
BAT LED is always on Battery is OK
SIM LED is green or amber Device is connected to the network
Coverage LED is green or amber Good coverage
SLIC LED is green Device is in standby
J6
11. To x the device in position, drill two holes in the wall and insert the wall plugs and
screws provided with the device. Hang the DCP on these two points using the tear-
shaped holes at the back box of the DCP (mid points of holes are 105mm apart).
12. If a non-Avire SIM card is used, APN settings must be set prior to conguring it on
the Avire Hub; please refer to “Setting Parameters on non-Avire SIM cards” (page
6). If the SIM LED is ashing red, please see “SIM Card unlocking” (see page 5).
105mm
5
CONFIGURING THE DCP
Avire App
The Avire App (available on Apple App store and Google play) allows installers to
quickly and intuitively setup/congure the DCP and connect to the Avire Hub. The Avire
App removes the need for conguration using SMS and instead walks you through the
connection process on your smart phone. The App is available at the links below:
Digit 1 Digit 2 Digit 3 Digit 4
Continent SIM0 Network Type of connection SIM1 Network
The Digital Communications Platform comes pre-congured with factory settings of 0000 (this
conguration doesn’t specify any use case or country).
P091 Digit 1 Digit 2 Digit 3 Digit 4
Country SIM0 Network Type of Connection SIM1 Network
Single Sim 4 = (UK) 3 = (EE) 1 = (Avire HUB) 0 = (No SIM)
SMS Setup
Parameter 91 (P091) allows quick and easy conguration of APN settings, depending on
the country and network provider. Congure settings for the DCP based on the tables
below by texting the DCP using P091.
Example
2
6
0
Digit 1 0 1-6 7 8
Continent Default Europe Americas Australasia
Digit 2 & 4 1 2 3 4 5 6
Country Spain Portugal Italy UK Germany France
0default default default default default default
1AvireSim AvireSim AvireSim AvireSim AvireSim AvireSim
2Telefonica MEO Wind O2 Telekom DE Orange
3Orange NOS TIM EE ABD SFR
4Vodafone Vodafone Vodafone Vodafone Vodafone DE Bouygues Telecom
5Iliad 3 O2 DE Free Mobile
6tre(3) Virgin BASE
71P Swisscom
8Telit Telit Telit BT A1 Telit
9GiGa tmobileAT
Digit 3 0 1 2 3
Type Transparent Gateway Avire Hub P100 P100 + Avire Hub
Transparent Gateway Enables DCP to provide data/cellular connection to a
device which is connected to it. This setting is often used
when connecting the DCP to a non-avire PSTN phone or
to a lift controller.
Avire Hub Avire Hub setting is used when the intention is to monitor
your *devices using the Avire Hub
P100 P100 setting allows connection to devices utilising the
P100 protocol without connection to the Avire Hub
P100 + Hub P100 + Hub allows connection to devices utilising P100
protocol and monitoring of devices through the Avire Hub
If your SIM’s APN details are not listed on the previous tables, you will need to obtain
this information and then manually programme the details using Parameters 60 and 61.
Further details on these settings can be found using this link.
*Avire Ecosystem devices only
go.avire-global.com/DCP
7
OPTION 2
If super settings are not used, then APN settings need to be set up manually:
Command Description
P060 (P zero six zero) APN address
P061 (P zero six one) APN username
P062 (P zero six two) APN password
P063 (P zero six three) Type of connection
These parameters must be congured by sending an SMS to the SIM card number.
Examples for various regional providers are shown below:
Carrier P060 P061 P062
Vodafone UK wap.vodafone.co.uk wap wap
DeutscheTelekom Telekom (blank) (blank)
Orange France Orange.fr orange orange
Other APN settings are available on the web and can be easily found online. If an APN
is incorrect for the provider or is not set up correctly, the DCP will not check into the
Avire HUB.
Important Note: The default PIN code for DCP is always 1234.
Example of an SMS for single SIM card device (for example if the SIM card is from
Vodafone):
Pin1234,P060 wap.vodafone.co.uk,P061 wap,P062 wap,P063 1
If either APN username and/or APN password are (blank) (DeutscheTelekom example)
and the DCP is congured to be used with the Avire Hub, then the text message will be:
Pin1234,P060 (blank),P063 1
If everything is congured correctly, you will receive a text within a few minutes:
P063 0 1 2 3
Type Transparent Gateway Avire Hub P100 P100 + Avire Hub
8
Obtaining the CCID number
AVIRE SIM CARDS
Avire SIM cards come unlocked to be used with our products
immediately after plugging them in and setting correct Super settings.
You will need to know the CCID number to add this information to the
Avire Hub.
The CCID Number is shown on the back of the SIM card and also on the outer plastic
case of the SIM card (highlighted in red on the picture below).
Important Note: Make sure the complete CCID number is entered when adding the
DCP to the Avire Hub, or the DCP will not be able to communicate with the Hub.
NON-AVIRE SIM CARDS
It is also possible to retrieve the CCID number by sending a SMS command to a SIM
card telephone number; the command needs to be separated by a comma as shown
below:
Pin1234,P005?
You will receive a text with the CCID number back within a few minutes; in this example,
the number shown after “P005=” is the CCID number of this SIM card.
Important note: Example CCID number is highlighted in red on picture above.
You will need to retrieve the CCID number when the DCP installation is set up on the
Avire Hub online platform. Please make sure that if this installation is set up by the
oce, they know the details for installation.
9
AVIRE HUB
Please contact your local sales oce for access to the Avire Hub.
The link to the Avire Hub is http://avirehub.avire-global.com
To view installation tutorial videos please go to the “Help” section of the Avire Hub.
Click on “Installations” in the menu on the side
and then on “Buildings”. Inside of “Buildings” tab
click on “Create Building”
Enter information relevant to your installation in General data
10
On the other side of the page please enter the number of elevator group you have in
this installation and how many elevators you have in the group. As an example, if this
is a simplex installation the number of elevator groups will be “1” and the number of
elevators will also be “1”. If it’s a duplex installation it will be “1” and “2” respectively.
You can also edit the group names to easily identify installations. Once all information
is entered click “Next”.
In the new page, you should be able to see “Groups” and “Elevators”. Click on “Add
gateway” under the term “Gateway” and select the “DCP” option (see example image
below). A pop up window will appear where you can enter the SIM information (Note:
Avire SIM cards have the country code (+31), but this has no impact on costs). Enter all
required information and then click “Apply”.
Note: The Background Call Period is the frequency of test checks and 72hrs is the
maximum period as per guidance from standards.
Otros manuales para DCP
3
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Idiomas:
Otros manuales de Sistema de conferencias de AVIRE
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
