Avigilon H6A Series Manual de usuario

H6A Camera Web Interface

User Guide

Avigilon H6A, H6X, and H6XP IP Camera Models:

H6A-xxx H6X-xxx 

H6A-xxx-IR H6X-xxx-IR 

AVIGILONCONTROL CENTER, ACC, ACCESS CONTROL MANAGER, and ACM are trademarks of Avigilon

Corporation. Android is a trademark of Google LLC. Apple, Safari and Mac are trademarks of Apple Inc,

registered in the US and other countries. Firefox is a registered trademark of the Mozilla Foundation in the US

and other countries. Other names or logos mentioned herein may be the trademarks of their respective

owners. The absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a

disclaimer of ownership of the related trademark. Covered by one or more claims of the patents listed at

patentlist.hevcadvance.com.

This document has been compiled and published using product descriptions and specifications available at

the time of publication. The contents of this document and the specifications of the products discussed

herein are subject to change without notice. Avigilon Corporation reserves the right to make any such

changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the

completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,

or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages

(including consequential damages) caused by reliance on the information presented herein.

Avigilon Corporation

avigilon.com

PDF-H6AWebUI-A

Revision: 1 - EN

20231018

Table of Contents

Introduction 1

System Requirements 1

Other Web Interface Guides 1

Accessing the Camera Web Interface 2

Creating the Initial User and Logging In 2

Live View 3

Saving a Still Image 3

Setup 4

General 5

Network 6

Configuring 802.1x Port-Based Authentication 9

Switching 802.1x Authentication Profiles 9

Deleting an 802.1x Authentication Profile 10

Configuring SNMP 10

IP Filter 11

Security Settings 12

Compression and Image Rate 12

Enabling HDSMSmartCodec™ Technology Settings 13

Viewing the RTSP Stream URI 14

Accessing the Still Image URI 15

HDSMSmartCodec Technology Advanced Settings 15

Motion Detection 15

Tamper Detection 16

Analytics 17

Audio Analytics 17

Privacy Zones 18

Setting a Privacy Zone 19

Deleting a Privacy Zone 19

Setting a Removable Privacy Zone for Specific Users 19

Storage 20

Enabling Onboard Storage 20

ONVIFProfile G 21

Downloading Recorded Video from the Web Interface 21

Downloading Recorded Video from the SD Card 22

Deleting Recorded Video 23

iii

SD Card Failures 23

Digital Inputs and Outputs 23

Audio 24

Users 25

Adding a User 25

Editing Users and Passwords 25

Removing a User 25

Keeping Usernames and Passwords After Firmware Revert 25

System 26

Upgrading the Camera Firmware 26

Licensing 27

Automatic Activation 27

ManualActivation 27

Device Log 27

Disable WebUI 28

About 29

Checking a Camera's Power Source 29

Introduction

Avigilon High Definition IP cameras include a web interface that allows you to view the live video and

configure the camera through a web browser.

Before you access the web interface, make sure all the procedures described in the camera installation guide

have been completed.

Tip: Features and options are disabled if they are not supported by the camera.

System RequirementsThe following browsers are recommended when accessing the web interface from any Windows, Mac, or

mobile device:

lMozilla Firefox version 96.0.2 (64-bit) or later

lGoogle Chrome™ version 97.0.4692.71 (64-bit, official build) or later

lMicrosoft Edge version 97.0.1072.76 (64-bit, official build) or later

Note: The web interface may work with older or unsupported browsers, but this has not been tested.

Other Web Interface GuidesCheck out these other Web Interface Guides for other types of Avigilon cameras:

lAPD Sensor Web Interface Guide — for Avigilon presence detectors.

Introduction 1

Accessing the Camera Web Interface

After the camera has been installed, you need the camera's IP address to access the web interface. The IP

address can be found in the following:

lThe Avigilon Control Center (ACC) software — Open the Setup tab to see the details of the selected

camera.

lMotorola Solutions' Camera Configuration Tool (CCT) — Go to the Network tab to see the details of the

selected cameras.

Once you have the IP address, complete the following procedure to access the web interface:

Note: The web browser must be configured to accept cookies or the camera web interface will not

function correctly.

1. On a computer with access to the same network as the camera, enter the camera's IP address into a

web browser:

http://<camera IP address>/

For example: http://192.168.1.40/

2. You will automatically be prompted to enter your username and password to access the camera. If the

device is in the factory default state and was manufactured after January 1, 2020, you will be asked to

create a user with administrator privileges before the device will be operational. For more information,

see Creating the Initial User and Logging In on page1.

Creating the Initial User and Logging InNew cameras do not have a default username and password and will be in a factory default state.

Important: You must create a user with administrator privileges before the camera is operational.

When logging into the camera for the first time, you will be redirected to the Add User page to create an

administrator user:

1. Enter a new User Name or keep the default administrator name.

2. Enter a new Password for the user. We recommend using a complex and unique password. Avoid

using an empty password as they are not supported across all platforms and devices.

3. Confirm the new password.

4. For the first user, Administrator must be selected in the Security Group drop-down menu.

5. Click Apply. After creating the user, you will be asked to login.

Accessing the Camera Web Interface 2

Live View

After you log in, the first page you see is the Live View. The Live View contains an image panel that displays

the live video stream.

Use the menu links in the top-left corner to navigate through the web interface. Click Live View any time to

return to this page.

Tip: Features and options are disabled if they are not supported by the camera.

Saving a Still ImageIf you see the Save Still to SDCard button from the Live View page, the camera supports the ability to take

snapshots of live video from the web interface.

To use this feature, the following settings are required for the camera:

lThere is an SD card inserted in the camera. For more information, see the camera's installation guide.

Saving an image to the SD card is not supported if you are using FIPS Level 3 encryption with a CryptR

micro card inserted in the SD slot.

lThe camera's onboard storage settings are enabled on the Storage page. For more information, see

Storage on page20.

lThe camera's video format must be set to MJPEG in the Compression and Image Rate page. For more

information, see Compression and Image Rate on page12.

Once all the requirements have been met, you can click Save Still to SDCard and the image that is displayed

in the Live View page is automatically saved to the SD card.

To download the snapshot, see Downloading Recorded Video from the Web Interface on page21.

Live View 3

Setup

Note: Certain options are not displayed if they are not supported by the camera model you are using

or if you do not have the required user permissions.

The factory default settings allow you to use the camera or encoder immediately after installation. If you have

special requirements, you can customize the settings through the web interface. In the top-left menu area,

click Setup to display all the available setup pages.

A Restore Defaults button is available on each setup page to restore the factory default settings.

Be aware that some settings are only available through the camera's web interface and cannot be changed in

the network video management software.

Setup 4

GeneralWhen you select Setup, the first page you see is the General page. The General page allows you to set the

camera's identity.

Tip: Features and options are disabled if they are not supported by the camera.

Note: If a camera with video analytics or unusual motion detection is physically moved or adjusted,

or if the focus or zoom level is changed, reset the learning progress to provide accurate results. If the

camera's image rate and compression or display settings are updated, the learning progress may

reset automatically.

1. In the Name field, give the camera a meaningful name.

2. In the Location field, describe the camera's location.

3. Select the Disable device status LEDs check box to disable the LED indicators located on the camera.

4. From the Mode drop-down list, select the mode that the camera will operate in.

This option is only displayed for higher bandwidth usage cameras.

lFull Feature — This is the standard operating mode. Offers the full functionality of the camera.

lHigh Framerate — The 2MP and 4MP camera models have a High Frame Rate mode, allowing

these cameras to reach higher frame rates while disabling analytics.

ModelsFeatures Impacted by High Framerate2 MP H6A Cameras

2 MP H6X Cameras

4 MP H6ACameras

4 MP H6XCameras

oIncreased maximum frame rate

oAnalytics disabled

lNo Smart Analytics — This mode will disable smart analytics. This option is for deployments

where camera based video analytics would interfere with other analytics integrations.

5. Select any of the Overlay Setting check boxes to display and stamp that information on the camera's

video stream. The options are:

lDisplay DateSelecting the Display Date check box also enables the Date Format drop-down list. From the

list, choose the date format which will be used to display the date.

lDisplay TimeGeneral 5

lDisplay GMT OffsetlDisplay NamelDisplay Location6. In the Time Settings area, select how the camera keeps time.

lIf you prefer to manually set the camera’s date and time, enter the time zone on this page.

lSelect the Automatically adjust clock for Daylight Savings Time check box, if required.

lIf you prefer to auto-synchronize the camera’s date and time with an NTP server, configure the

NTP server on the Network page.

At the bottom of the page, you can click on the (Configure NTP Server) link to go to the Network

page. For more information on configuring the NTP server, see Network below.

CAUTION — The time setting must always be current or the ACCsoftware will reject the video stream

from the camera. To ensure that the time is always current you should do one of the following:

lSet up NTP on the DHCPserver used by the ACCsoftware.

lUse a valid public NTP server.

lManually set the correct time in the Time Settings fields.

7. Click Apply to save your settings.

NetworkOn the Network page, you can change how the camera connects to the server network and choose how the

camera keeps time.

1. At the top of the page, select how the camera obtains an IP address:

lObtain an IP address automatically: select this option to connect to the network through an

automatically assigned IP address.

The IP address is obtained from a DHCP server. If it cannot obtain an address, the IP address

will default to addresses in the 169.254.x.x range.

lUse the following IP address: select this option to manually assign a static IP address.

oIP Address: Enter the IP Address you want to use.

oSubnet Mask: Enter the Subnet Mask you want to use.

oDefault Gateway: Enter the Default Gateway you want to use.

2. Select the Disable setting static IP address through ARP/Ping method check box to disable the

ARP/Ping method of setting an IP address.

3. If the camera supports IPv6, select the Enable IPv6 check box to configure the following settings.

Note: Enabling IPv6 does not disable IPv4 settings.

Network 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Avigilon

Avigilon

Avigilon 1.0-H3M-DO1 Manual de usuario

Avigilon

Avigilon 1.0-H3-B2 Manual de usuario

Avigilon

Avigilon H4A-DO1, H4A-DO1-IR, H4A-DO2, H4A-G-DO1-IR Manual de usuario

Avigilon

Avigilon 1.0C-H4A-B1 Manual de usuario

Avigilon

Avigilon H3-BO1-IR Manual de usuario

Avigilon

Avigilon H4 Manual de usuario

Avigilon

Avigilon 2.0C-H6SL-D1 Manual de usuario

Avigilon

Avigilon 5.0-H3-DP2 Manual de usuario

Avigilon

Avigilon H3-3MH-DC1 Manual de usuario

Avigilon

Avigilon H5 Manual de usuario

Avigilon

Avigilon 1.0-H3M-DP1 Manual de usuario

Avigilon

Avigilon 1.3L-H3-DC2 Manual de usuario

Avigilon

Avigilon 1.0-H3A-DO1 Manual de usuario

Avigilon

Avigilon H4A-G-B Manual de usuario

Avigilon

Avigilon 2.0C-H6A-D1 Manual de usuario

Avigilon

Avigilon 1.0-H3M-DC1 Manual de usuario

Avigilon

Avigilon 1.0W-H3PTZ-DP20 Manual de usuario

Avigilon

Avigilon 12W-H3-4MH-DP1 Manual de usuario

Avigilon

Avigilon H4A-G-BO1-IR Manual de usuario

Avigilon

Avigilon H4A-B1 Manual de usuario

Avigilon

Avigilon 1.0-H3-D1 Manual de usuario

Avigilon

Avigilon H3-B1 Manual de usuario

Avigilon

Avigilon 1.3L-H3-D2 Manual de usuario

Avigilon

Avigilon H5A Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario