Avigilon 3.0C-H5A-CR2-IR Manual de usuario
Installation Guide
Avigilon H5A Corner Camera Models:
3.0C-H5A-CR2-IR 3.0C-H5A-CR2-IR-SS
5.0C-H5A-CR2-IR 5.0C-H5A-CR2-IR-SS
Legal Notices
© 2022,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON CONTROL
CENTER, and ACC are trademarks of Avigilon Corporation. Other names or logos mentioned herein may be
the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each
trademark in this document or at all is not a disclaimer of ownership of the related trademark. Avigilon
Corporation protects its innovations with patents issued in the United States of America and other
jurisdictions worldwide (see avigilon.com/patents). Unless stated explicitly and in writing, no license is
granted with respect to any copyright, industrial design, trademark, patent or other intellectual property rights
of Avigilon Corporation or its licensors.
Disclaimer
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
PDF-H5A-CR2-A
Revision: 2 - EN
20220308
ii
Important Safety Information
This manual provides installation and operation information and precautions for the use of this device.
Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual
carefully. Please provide this manual to the owner of the equipment for future reference.
This Warning symbol indicates the presence of dangerous voltage within and outside the product
enclosure that may result in a risk of electric shock, serious injury or death to persons if proper
precautions are not followed.
This Caution symbol alerts the user to the presence of hazards that may cause minor or moderate
injury to persons, damage to property or damage to the product itself if proper precautions are not
followed.
WARNING — Failure to observe the following instructions may result in severe injury or death.
lInstallation must be performed by qualified personnel only, and must conform to all local codes.
lThis product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or
“Limited Power Source” with output rated 12 VDC or 24 VAC, 13 W min. or Power over Ethernet (PoE),
13 W min.
lDo not connect directly to mains power for any reason.
CAUTION — Failure to observe the following instructions may result in injury to persons or damage
to the device.
lDo not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure may
cause permanent damage to the image sensor.
lDo not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.
lDo not subject the device cables to excessive stress, heavy loads or pinching.
lDo not open or disassemble the device. There are no user serviceable parts.
lRefer all device servicing to qualified personnel. Servicing may be required when the device has been
damaged (such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not
operate normally, or has been dropped.
lDo not use strong or abrasive detergents when cleaning the device body.
lUse only accessories recommended by Avigilon.
lThis device complies with EN 60529 IP66 and IP67 ratings.
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
iii
This Class B digital apparatus complies with Canadian ICES-003.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and the receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
lConsult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties
authorized by Avigilon Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose of it according to your local
environmental laws and guidelines.
Risk of fire, explosion, and burns. Do not disassemble, crush, heat above 100 °C (212 °F), or incinerate.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of
separately from household waste. When this product reaches its end of life, take it to a collection point
designated by local authorities. Some collection points accept products for free. The separate collection and
recycling of your product at the time of disposal will help conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment.
iv
Table of Contents
Overview 1
Assembled View 1
Housing Front View 2
Gimbal Bottom View 3
Gimbal Front View 4
Housing Rear View 5
Cover - Rear View 6
Conduit Box Accessory View 7
Installation 8
Pre-Deployment In-Box Configuration 8
Required Tools and Materials 8
Camera Package Contents 9
Installation Steps 9
Removing the Front Cover and Gimbal 9
Preparing the Mounting Grommets 12
Mounting and Aiming Video Analytics Cameras 13
Inserting Cables through the Sealing Grommet 13
Mounting the Corner Camera Base 14
Connecting Cables 17
Mounting the Camera Gimbal to the Base 18
Installing the Front Cover 19
Initializing a Camera Username and Password 21
(Optional) Using the USB Wi-Fi Adapter 21
Assigning an IP Address 22
Accessing the Live VideoStream 22
(Optional) Configuring microSD Card Storage 22
Focusing the Camera 23
Configuring the Camera 23
Installation with the Conduit Box Accessory 24
Mounting the Conduit Gang Box 24
Mounting the Camera Base to the Conduit Box 26
Mounting the Camera Gimbal 30
Installing the Front Cover 31
Cable Connections 33
v
Connecting External Power 33
Connecting to External Devices 33
Connection Status LED Indicator 35
Troubleshooting Network Connections and LED Behavior 35
Resetting to Factory Default Settings 37
Setting the IP Address Using the ARP/Ping Method 38
Cleaning 39
Dome Bubble 39
Body 39
For More Information 40
Limited Warranty and Technical Support 41
vi
Overview
Assembled View
1. Front cover
Vandal resistant front cover.
2. Recording LED
LED turns on when the camera is streaming video to a local microSD card, ACC or another VMS
system, or the camera web interface.
3. Microphone
Built-in audio receiver.
4. Tamper resistant screws
Tamper resistant captive screws to fix the dome cover to the base.
Overview 1
Housing Front View
1. Camera lens
Lens that captures the video image.
2. LED cable
Connect the cable to the LED connector on the front cover to power the Recording LED and IR LED.
3. Microphone cable
Connect the cable to the microphone audio connector on the front cover to use the built-in
microphone.
4. Lanyard hook
A hook for connecting the lanyard on the camera cover.
Housing Front View 2
Gimbal Bottom View
1. Power connector block
Accepts a terminal block with either an AC or DC power connection. DC input can be either polarity.
Only required when Power over Ethernet is not available.
2. Ethernet port
Accepts an Ethernet connection to a network. Server communication and image data transmission
occurs over this connection. Also receives power when it is connected to a network that provides
Power over Ethernet.
3. Connection status LED indicator
Green LED provides information about device operation. For more information, see Connection Status
LED Indicator on page35.
4. Link LED indicator
Amber LED indicates if there is an active connection in the Ethernet port.
Gimbal Bottom View 3
Gimbal Front View
1. I/O connector block
Provides connections to external input/output devices.
2. Micro USB port
Accepts a micro USB to USB adapter. Only required when using the Avigilon USB Wi-Fi Adapter.
3. microSD card slot
Accepts a microSD card for onboard storage. For more information, see (Optional) Configuring
microSD Card Storage on page22.
Gimbal Front View 4
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Cámara digital de Avigilon
