Avigilon 2.0C-H6SL-BO1-IR Manual de usuario
Installation Guide
Avigilon H6SL Camera Models:
2.0C-H6SL-BO1-IR 3.0C-H6SL-BO1-IR
3.0C-H6SL-BO2-IR 5.0C-H6SL-BO1-IR
5.0C-H6SL-BO2-IR
Legal Notices
© 2023,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON CONTROL
CENTER, and ACC are trademarks of Avigilon Corporation. Other names or logos mentioned herein may be
the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each
trademark in this document or at all is not a disclaimer of ownership of the related trademark.
Disclaimer
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
PDF-H6SLBO-A
Revision: 1 - EN
20230228
2
Important Safety Information
This manual provides installation and operation information and precautions for the use of this device.
Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual
carefully. Please provide this manual to the owner of the equipment for future reference.
This Warning symbol indicates the presence of dangerous voltage within and outside the product
enclosure that may result in a risk of electric shock, serious injury or death to persons if proper
precautions are not followed.
This Caution symbol alerts the user to the presence of hazards that may cause minor or moderate
injury to persons, damage to property or damage to the product itself if proper precautions are not
followed.
WARNING — Failure to observe the following instructions may result in severe injury or death.
lInstallation must be performed by qualified personnel only, and must conform to all local codes.
lThis product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or
“Limited Power Source” with output rated 12 VDC 13 W min. or Power over Ethernet (PoE), 13 W min.
lDo not connect directly to mains power for any reason.
CAUTION — Failure to observe the following instructions may result in injury to persons or damage
to the device.
lDo not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure may
cause permanent damage to the image sensor.
lDo not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.
lDo not subject the device cables to excessive stress, heavy loads or pinching.
lDo not open or disassemble the device. There are no user serviceable parts.
lRefer all device servicing to qualified personnel. Servicing may be required when the device has been
damaged (such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not
operate normally, or has been dropped.
lDo not use strong or abrasive detergents when cleaning the device body.
lUse only accessories recommended by Avigilon.
lThis device complies with EN 60529 IP66 and IP67 ratings.
3
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003 (B)/NMB-3 (B).
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and the receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
lConsult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties
authorized by Avigilon Corporation could void the user’s authority to operate this equipment.
To meet the requirements of the EN 50121-4 Railway Applications Standard, use an external power supply or
POE injector that is also compliant with EN 50121-4. Please contact Avigilon for assistance regarding
supporting equipment.
To meet the requirements of the EN 50130-4 Alarm Systems Applications standard, use an external
uninterruptible power (UPS) supply.
This equipment contains a coin cell battery. Risk of fire, explosion, and burns. Do not disassemble, crush, heat
above 100°C (212°F), or incinerate.
The use of EMC compliant support and auxiliary equipment with this device is required in order to fully
comply with the EMC regulatory standards.
For Korea
4
IRSafety Information
Use appropriate shielding or eye protection.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose of it according to your local
environmental laws and guidelines.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of
separately from household waste. When this product reaches its end of life, take it to a collection point
designated by local authorities. Some collection points accept products for free. The separate collection and
recycling of your product at the time of disposal will help conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment.
5
Table of Contents
Overview 7
Junction Box View 7
Front View 7
Side View 8
Rear View 8
Configuration Panel View 9
Installation 10
Camera Package Contents 10
Installation Steps 10
Mounting the Bullet Camera 10
Removing the Configuration Panel Cover 14
Initializing a Camera Username and Password 15
(Optional) Using the USB Wi-Fi Adapter 15
Assigning an IP Address 16
Setting the IP Address Using the ARP/Ping Method 16
Accessing the Live VideoStream 17
Aiming the Camera 18
Zooming and Focusing the Camera 19
(Optional) Configuring microSD Card Storage 19
Configuring the Camera 20
Connecting to External Devices 21
Connection Status LED Indicator 22
Troubleshooting Network Connections and LED Behavior 22
Resetting to Factory Default Settings 24
For More Information 25
Limited Warranty and Technical Support 26
6
Overview
Junction Box View
1. Camera mounts
Points for installing the camera to the junction box.
2. Mounting hook slots
Points to hold the camera to the junction box while connecting the required cables.
3. Mounting holes
Holes for securing the junction box to the mounting surface.
Front View
1. IRIlluminator
Provides scene illumination in the IRspectrum.
2. Configuration panel cover
Covers the configuration panel.
Overview 7
Side View
1. Sun shroud
An adjustable cover to help protect the lens against glare from the sun.
2. Mount arm
Adjustable mount arm for positioning the camera.
3. Adjustment screws
Provides a locking mechanism for the mount arm.
Rear View
1. Ethernet port
Accepts power and Ethernet connection to the network. Server communication and image data
transmission also occur over this connection.
The camera can either be powered by Power over Ethernet (PoE) or 12 VDC Aux.
2. Serial number tag
Device information, product serial number and part number label.
3. Camera mounting screws
Screws for mounting the camera to the junction box.
4. Mounting hooks
Hooks to attach the camera to the junction box while connecting the required cables.
5. Power and I/O cables
Cables for connecting the camera to auxiliary power and I/O devices. For more information, see
Connecting to External Devices on page21.
Side View 8
Configuration Panel View
1. microSD card slot
Accepts a microSD card for onboard storage. For more information, see (Optional) Configuring
microSD Card Storage on page19.
2. Micro USB port
Accepts a micro USB to USB adapter. Only required when using the USB Wi-Fi Adapter.
3. Link LED indicator
Amber LED indicates if there is an active connection in the Ethernet port.
4. Connection status LED indicator
Green LED provides information about device operation. For more information, see Connection Status
LED Indicator on page22.
Configuration Panel View 9
Installation
Camera Package Contents
lAvigilon H6SL Bullet Camera
lJunction box
lMounting template sticker
l4 screws and anchors for solid walls
l4 screws for attachment to electrical box
lProtective rubber boot for Ethernet port
lTeflon tape
Installation Steps
Complete the following sections to install the device.
Mounting the Bullet Camera
If the cables for the camera will not be provided from inside the mounting surface, install the junction box first.
After you install the junction box, you can skip directly to step 3 of this procedure.
1. Use the mounting template to drill four mounting holes into the mounting surface.
2. Drill the cable entry hole into the mounting surface then pull the required Ethernet cable through the
cable entry hole.
Installation 10
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Cámara digital de Avigilon
