Avaya Cajun P580 Instrucciones de instalación y funcionamiento
© 2002 Avaya, Inc. December 2, 2002 1
User Guide Addendum for the Avaya
P580 and P882 Multiservice Switches,
Software Version 5.4
Overview
This addendum provides information and procedures that will be
added to later versions of the user documentation. Version 5.4 of the
application software is supported only by the M8000R-SUP
supervisor module.
This addendum is updated periodically with new information. To
download the most current version of this document, see http://
support.avaya.com. Click Product Documentation.
This addendum includes the following topics:
■New Hardware Features on page 2
■New Software Features on page 2
■Updated CLI Commands on page 4
■Logging ACL Activity on page 4
■Configuring Custom Access Types on page 9
■Configuring Utilization Monitoring on page 17
■Configuring Short-Lived IP Protocol Filters on page 22
■Documentation Updates and Corrections on page 26
■Technical Support on page 37
■Documentation Feedback on page 37
User Guide Addendum for the Avaya P580 and P882, v5.4
2 December 2, 2002 Part No. 610-0211-094
New Hardware Features
Version 5.4 provides support for the following new hardware:
■10-Gigabit Uplink module.
For information about how to install the 10-Gigabit Uplink
module, see Installing the Avaya 10-Gigabit Uplink Module. For
information about how to configure the module, see
Appendix A, "Configuring the Avaya 10-Gigabit Uplink
Module."
New Software Features
Version 5.4 provides support for the following new software
features:
Security Features ■ACL Logging. This feature logs information about a sampling
of packets that match specific rules in the active access
control list. For information on how to use the ACL Logging
feature, see Logging ACL Activity on page 4.
■Ability to select read-only permission or read-write
permission for custom access types. For information on how
to specify these permissions when you create a custom access
type, see Configuring Custom Access Types on page 9.
Performance
Features ■Utilization Monitoring. This feature makes it possible for you
to monitor utilization of the:
—CPU—the number of packets per second that the CPU on
the supervisor module routes (slow path).
—Forwarding engine—the number of packets per second
that the 80-series forwarding engines route. This statistic
includes packets routed by the forwarding engines on 80-
series media modules (FIRE) and on the supervisor
module (FORE).
For more information about the slow path and FIRE and
FORE paths, see “Routing Overview” in Chapter 1,
“Introduction,” of the Avaya P550R, P580, P880, and P882
Multiservice Switch User Guide.
Doc. No. 650-100-701
Part No. 610-0211-094 December 2, 2002 3
For each of these statistics, you can set a high threshold. If
this threshold is exceeded, the switch logs the event in the
event log. For information on how to configure utilization
monitoring, see "Configuring Utilization Monitoring" on
page 17.
■Short-lived protocol filters. This feature helps conserve the
forwarding engine resources of the switch. By using a short-
lived protocol filter, you can set the switch to use the slow
path to route packets of a specific short-lived protocol. And
by using the slow path to route short-lived protocol traffic,
you conserve the resources of the forwarding engines.
For information on how to configure short-lived protocol
filters, see "Configuring Short-Lived IP Protocol Filters" on
page 22.
MIB Support ■The following groups and objects in the RMON2 MIB,
documented in RFC 2021:
—Protocol Directory (protocolDir) Group
• Protocol Directory Last Change
(protocolDirLastChange) object
• Protocol Directory Table (protocolDirTable)
The following protocols are supported in this table:
Ethernet II, SNAP, IP, IPX, TCP, and UDP.
—Address Map (addressMap) Group:
• Address Map Table (addressMapTable)
—Probe Configuration (probeConfig) Group
• Probe Capabilities (probeCapabilities) object
• Network Configuration Table (netConfigTable)
• Network Default Gateway (netDefaultGateway) object
■The following table in the HCRMON MIB (draft-ietf-
rmonmib-hcrmon-10.mib), documented in RFC 3273:
—Ethernet Statistics High Capacity Table
(etherStatsHighCapacityTable)
User Guide Addendum for the Avaya P580 and P882, v5.4
4 December 2, 2002 Part No. 610-0211-094
Updated CLI Commands
show custom-access-type
Command Mode User.
Description Displays the custom access types that are currently configured on
the switch.
Syntax show custom-access-type
Sample Output The following example displays the custom access types that are
currently configured on a switch:
Avaya>show custom-access-type
Systems Avaya P580 and P882 Multiservice switches.
Logging ACL Activity
Overview
You can now log information about packets that match specific rules
in the active access control list (ACL). Each log entry contains the
following information:
■Source and destination IP address.
■Protocol ID (RFC 1700 defines these ID numbers).
■Time that the match occurred.
■Index number of the access rule that was matched.
Custom Access Type
Name
----------------
Sys
Cfg.
----
-
Mod
Port
Cfg.
----
-
Event
Mgmt.
-----
L2
Switching
---------
Routing
-------
admin rw rw rw rw rw
CAT1 ro rw -- -- --
Doc. No. 650-100-701
Part No. 610-0211-094 December 2, 2002 5
■Forwarding information:
—The priority of the packet if the ACL assigns it a priority
and forwards it.
—Forward with no change in priority if the ACL
forwards the packet without changing its priority.
—FILTER if the ACL blocks the packet.
To avoid excessive consumption of the switch resources, ACL
matches are logged for slow path traffic at specific time intervals.
You can set the interval at which the matches are logged. The
default setting is two seconds.
ACL matches are not logged for FIRE path or FORE path traffic. For
more information about the slow path and FIRE and FORE paths,
see “Routing Overview” in Chapter 1, “Introduction,” of the Avaya
P550R, P580, P880, and P882 Multiservice Switch User Guide.
This section includes procedures for the following tasks:
■Enabling ACL Logging on page 5
■Setting a Logging Interval on page 7
Enabling ACL Logging
Web Agent
Procedure To enable ACL logging by using the Web Agent:
1. In the navigation pane, expand the Routing > IP >
Configuration folders, and then click Access Lists.
The IP Access List Web page is displayed in the content pane.
See Figure 1.
User Guide Addendum for the Avaya P580 and P882, v5.4
6 December 2, 2002 Part No. 610-0211-094
Figure 1. IP Access List Web page
2. Select the check box next to each rule that you want to
enable ACL logging for.
3. In the Rule Match Logging column, select Enable for each
access rule that you want to enable ACL logging for.
The default setting for ACL logging is disabled.
4. Click Apply.
CLI Command To enable ACL logging, enter Global Configuration mode and use the
following command:
ip acl-logging enable <access-list-name> <rule-number>
The default setting for ACL logging is disabled.
Table 1. Keywords, Arguments, and Options
Keyword, Argument,
or Option Definition
<access-list-name> The access list that contains the access
rule for which you want to enable ACL
logging.
<rule-number> The number of the access rule for which
you want to enable ACL logging.
Doc. No. 650-100-701
Part No. 610-0211-094 December 2, 2002 7
To disable ACL logging, enter Global Configuration mode and use the
following command:
ip acl-logging disable <access-list-name> <rule-number>
Sample Event Log
Entries Figure 2 displays sample ACL matches in the event log.
Figure 2. Sample ACL matches in the event log
Setting a Logging Interval
Web Agent
Procedure To set the interval for ACL logging:
1. In the navigation pane, expand the Routing > IP >
Configuration folders, and then click Access Control.
The IP Access Control Web page is displayed in the content
pane. See Figure 3.
User Guide Addendum for the Avaya P580 and P882, v5.4
8 December 2, 2002 Part No. 610-0211-094
Figure 3. IP Access Control Web page
2. In the Interval between logging of Access Rule Matches
(in seconds) field, enter the interval at which you want ACL
matches logged. Enter an interval from 1 to 60 seconds.
The default setting is 2 seconds.
3. Click Apply.
CLI Command To set the interval for ACL logging, enter Global Configuration mode
and use the following command:
ip acl-logging logging-interval <time-in-seconds>
The default setting is 2 seconds.
Table 2. Keywords, Arguments, and Options
Keyword, Argument,
or Option Definition
<time-in-seconds> The interval at which you want ACL
matches logged. Enter an interval from 1
to 60 seconds.
Doc. No. 650-100-701
Part No. 610-0211-094 December 2, 2002 9
Configuring Custom Access Types
This section contains procedures for the following tasks:
■Creating a Custom Access Type on page 9
■Viewing Custom Access Types on page 13
■Modifying a Custom Access Type on page 14
* Note: To log in to the ATM Uplink module, a user must:
• Have read-write access to the Modules and Ports
Management features.
• Enter Privileged mode or Global Configuration mode to
enter the session <slot number> command.
In earlier versions of application software, you could log
in to the ATM Uplink module from User mode. This
change in functionality prevents unauthorized users from
logging in to the ATM Uplink module.
Creating a Custom Access Type
Web Agent
Procedure To create a custom access type:
1. In the navigation pane, expand the System >
Administration folders, and then click Custom Access
Types.
The Custom Access Types Web page is displayed in the
content pane. See Figure 4.
User Guide Addendum for the Avaya P580 and P882, v5.4
10 December 2, 2002 Part No. 610-0211-094
Figure 4. Custom Access Types Web page
2. On the Custom Access Types Web page, click Create.
The Create Custom Access Type Web page is displayed in the
content pane. See Figure 5.
Otros manuales para Cajun P580
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Avaya
Avaya
Avaya P130 SMON Manual de usuario
Avaya
Avaya 8600 Hoja de instrucciones
Avaya
Avaya Cajun P550R Cómo utilizar
Avaya
Avaya Ethernet switches Manual de usuario
Avaya
Avaya MX10 Manual de usuario
Avaya
Avaya P113F Manual de usuario
Avaya
Avaya ERS 3500 Series Manual de usuario
Avaya
Avaya P333R-LB Guía del usuario
Avaya
Avaya 8300 Series Instrucciones de uso
Avaya
Avaya P460 Manual del producto
Avaya
Avaya P334T Manual de usuario
Avaya
Avaya Cajun P333T Manual de usuario
Avaya
Avaya 5900 Series Manual de usuario
Avaya
Avaya 5900 Series Manual de usuario
Avaya
Avaya 8000 Series Manual de instrucciones
Avaya
Avaya C360 Manager Manual de usuario
Avaya
Avaya 5000 Series Manual de usuario
Avaya
Avaya Ethernet Routing Switch 8300 Series Manual de usuario
Avaya
Avaya VSP 7000 Series Manual de instrucciones
Avaya
Avaya ERS 4000 Series Manual de usuario
