AUTOTECH 10.525.1128K Manual de usuario

A U T O T E C H

Phone 949.240.4000 Fax 949.240.045032240-E Paseo Adelanto, San Juan Capistrano, CA 92675

Part Number: 10.525.1128K

Description: Non-Adjustable rear swaybar installation for A2 & A3 chassis

Notes: These performance swaybars utilize Autotech’s unique sliding endlink design

that prevents binding of the bar (and preloading of the suspension) due to

locational differences between the mounting points of the rear suspension and the

swaybar itself.

TOOLS REQUIRED: PARTS LIST:

1. jackstands 1. rear swaybar

2. electric drill and 1O.5mm (27/64")bit 2. (4) poly bushings

3. silicone lubricant 3. (4) steel ring mounts

4. metric wrenches, 13 to 17mm 4. (2) 1Omm rod ends

5. tape measure 5. (6) 1Omm hardened washers

6. moly grease 6. (2) 1Omm thin jam nuts (1128K only)

7. (2) 1Omm nylock nuts

8. (2) M10x90 shock bolts

Procedure:

1. Apply a generous amount of waterproof grease to the inside of the bushings, and some sili-

cone spray along each of the bends on the swaybar.

2. Slide the two inboard mounts onto the swaybar and push them past both bends so that

they end up on the middle, straight section of the swaybar. The inboard mounts will be

installed on the axlebeam when they are as far apart from each other as possible with-

out overlapping any of the bends on the bar. Measure, and take note of this distance.

The distance from stud to stud on the inboard mounts should be approximately as fol-

lows:

A2/A3 Chassis 29 inches

A4 Chassis 25 inches

3. Raise the rear of the car and place it on jackstands. Be sure that the car is in gear, the

front wheels are chocked, and that it cannot roll.

www.autotech.com

A2/A3 = 29.0 in

A4/B5 = 25.0 in

Installation Instructions

4. Mark the axlebeam's crossmember for the hole locations using the distance you measured

in step 1. The holes should be centered left-to-right. Use the tape to measure 1.5 inches up

from the leading edge of the crossmember. The holes should end up just below the center

on the lower angled face of the beam.

5. Drill the two 1O.5mm (13/32" - 27/64") holes in the crossmember. It is a good idea to drill a

pilot hole ﬁrst so that the larger drill bit does not have to work so hard.

6. Thread the remaining two ring mounts (on A2/A3: with their jam nuts) into the rod ends.

Do not tighten them as yet.

7. Push each end of the swaybar into the end bushings. A small amount of silicone lubricant or

a ﬁlm of moly grease applied to the bar end and bushing eases the task.

8. Now swing the swaybar forward in order to push the inboard mounting studs through the

drilled holes in the crossmemeber. Be sure to capture a washer on each side of the hole

before attaching each inboard mount with the nylock nut.

9t. Go back and tighten the jam nuts against the rod ends (A2/A3 only). Once that is done,

recheck all fasteners to be sure they are tightened properly.

1.5 in

factory bar

rear axlebeam section - side view

rear shock

mount

factory nut

new longer bolt rod end washer

jam nut

ring mount

with bushing

rear view of endlink assembly

Tabla de contenidos

Otros manuales de Accesorios para automóviles de AUTOTECH

AUTOTECH

AUTOTECH 10.129.020K-021 Manual de usuario

AUTOTECH

AUTOTECH 10.864.102K Manual de usuario

AUTOTECH

AUTOTECH 10.430.005K-009K Manual de usuario

AUTOTECH

AUTOTECH 10.525.1129K Manual de usuario

AUTOTECH

AUTOTECH 10.525.1529K Manual de usuario

AUTOTECH

AUTOTECH 10.251.134K Manual de usuario

AUTOTECH

AUTOTECH 10.698.400K Manual de usuario

AUTOTECH

AUTOTECH 10.109.420 Manual de usuario

AUTOTECH

AUTOTECH 10.430.210K211K213K215K Manual de usuario

AUTOTECH

AUTOTECH 10.109.405K Manual de usuario

AUTOTECH

AUTOTECH 10.998.230K Manual de usuario

AUTOTECH

AUTOTECH 10.425.1425GK Manual de usuario

AUTOTECH

AUTOTECH 10.530.001K-002K Manual de usuario

AUTOTECH

AUTOTECH 10.109.01.109 Manual de usuario

AUTOTECH

AUTOTECH 10.297.300K-303K Manual de usuario

AUTOTECH

AUTOTECH 10.109.01.102 Manual de usuario

AUTOTECH

AUTOTECH 10.109.423 Manual de usuario

AUTOTECH

AUTOTECH 10.715.012K Manual de usuario

AUTOTECH

AUTOTECH 10.525.1722K Manual de usuario

AUTOTECH

AUTOTECH 10.425.1526GK Manual de usuario

AUTOTECH

AUTOTECH 10.109.418K Manual de usuario

AUTOTECH

AUTOTECH 10.115.410K Manual de usuario

AUTOTECH

AUTOTECH 10.698.006K Manual de usuario

AUTOTECH

AUTOTECH 10.435.001K-002K Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario