Automatic Technology Hiro GDO-12V1 Manual de usuario

Doc # 160055_02

Part # 13418

Released 21/02/19

High Rolling Door Opener

GDO-12 HiR

2GDO-12V1 Hiro™Installation Instructions

WARNING!: It is vital for the safety of persons to follow all

instructions. Failure to comply with the installation instructions

and the safety warnings may result in serious personal injury

and/or property and remote control opener damage. Please

save these instructions for future reference.

ELECTROCUTION!: To reduce the risk of electric shock, this

equipmenthasagroundingtypeplugthathasathird(grounding)

pin. This plug will only fit into a grounding type outlet. If the

plug does not fit into the outlet, contact a qualified electrician

to install the proper outlet. Do not change the plug in any way.

This operator is not equipped for permanent wiring. Contact a

qualified electrician to install a suitable receptacle if one is not

available.

Installation Instructions GDO-12V1 Hiro™3

1. Safety Information 4

2. Specifications 5

3. Set Up Requirements 6

4. Pre-Installation Requirements 7

4.1 Door Operation 7

4.2 Unsuitable Door Types 7

4.3 Position 7

4.4 Power Supply 7

4.5 Sideroom 7

4.6 Forks 7

5. Opener Safety & Security 8

5.1 The Door CAN NOT be used by the opener when: 8

5.2 The Door CAN be used when: 8

5.3 To Disengage the Opener: 8

5.4 To Re-Engage the Opener: 8

6. Installation Instructions 8

6.1 Door Preparation 9

6.1.1 Preparation 9

6.1.2 Pinning the Door to the drum: 9

6.2 Propping the Door 10

6.3 Fitting the Opener 10

6.4 Setting Limits 11

6.4.1 Setting Travel Limits 11

6.4.2 Set the Limit Positions 11

6.4.3 Resetting the Door Limit Positions 11

6.4.4 Setting Partial Open Position 11

6.4.5 Checking Partial Open Position 11

6.5 Safety Obstruction Force Test 12

6.5.1 Testing Close Cycle 12

6.5.1 Testing Open Cycle 12

6.6 Coding Transmitter 13

6.6.1 Transmitter Button to Operate Door 13

6.6.2 Erasing Programmed Codes 13

6.6.3 Selecting The Function To Be Coded 13

6.6.4 Activate Remote Code Set Mode 13

7. Operation Instructions 14

7.1 How to Use Your Opener 15

7.1.1 To Operate the opener: 15

7.1.2 Replacing the Battery: 3V Lithium Battery CR2032. 15

7.1.3 Battery Disposal 15

7.2 User Operating Controls 16

7.3 Door Status Indicators 16

8. Maintenance 17

9. Troubleshooting Guide 18

10. Appendix 19

A - Adjustment Mode Parameters 19

B - Motor Speed 19

C - LED Status 20

D - Setting Limits via Transmitter 21

E - Additional Transmitter Functions 22

11. Warranty and Exclusion of Liability 23

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or

otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic

Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any

person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener in accordance with these

installation instructions.

High Roll Up Garage Door Opener

GDO-12 HiR

4GDO-12V1 Hiro™Installation Instructions

1. Safety Information

Please read these important safety rules

These safety alert symbols indicate a personal

safety or property damage instruction exists.

READ THESE INSTRUCTIONS CAREFULLY.

This automatic garage door operator is designed and tested

to offer safe service provided it is installed and operated

in strict accordance with the following safety rules. Failure

to comply with the installation instructions and the safety

warnings may result in death, serious personal injury and/or

property damage.

WARNING!

• To reduce the risk of injury to persons – Use this operator only

with a rolling door. The drive must not be used with a door

incorporating a wicket door, unless the drive cannot be operated

with the wicket door open.

• This operator is a plug in domestic appliance and is designed

for indoor use only. It must be installed in a dry position that is

protected from the weather.

• Activate the operator only when the garage door is in full view,

free of obstructions and with the operator properly adjusted.

• The network device allows for operation of the door when not

in line-of-sight of the door and operator. Therefore the door

may operate unexpectedly, therefore do not allow anything to

stay in or near the path of the door.

• Watch the moving door and keep people away until the door is

completely opened or closed.

ELECTROCUTION:

• Installation and wiring must be in compliance with your local

building and electrical codes.

• This operator is not equipped for permanent wiring. Contact a

qualified electrician to install a suitable receptacle if one is not

available.

• To reduce the risk of electric shock, this equipment has a

grounding type plug that has a third (grounding) pin. This plug

will only fit into a grounding type outlet. If the plug does not fit

into outlet, contact a qualified electrician to install the proper

outlet. Do not change the plug in any way.

• If the power cord is damaged, it must be replaced by the

manufacturer, its service agent or a similarly qualified person in

order to avoid a hazard.

• Connect the power cord only to properly earthed mains. If an

extension lead must be used, make sure it is a 3-core lead and

approved to 7 amp capacity.

• This unit is not user serviceable. Unplug the power cord before

removing the cover. Ensure that the power cord is attached

clear of all moving parts. Ignoring these instructions can cause

electric shock.

CAUTION:

• If your garage has no pedestrian entrance door, an emergency

access device should be installed. This accessory allows manual

operation of the garage door from outside in case of power failure.

• Keep the garage door balanced. Sticking or binding doors must be

repaired. Garage doors, door springs, brackets and their hardware

are under extreme tension and can cause serious personal injury.

Do not attempt any garage door adjustment. Do not use if repair

or adjustment is needed. Call for professional garage door service.

• Position the Garage Door Operator so that the power plug is

accessible when inserted into the power outlet.

• Install the wall transmitter in a location where the garage door is

visible, but out of the reach of children at a height of at least 5 feet

(1.53m).

• To avoid serious personal injury from entanglement, remove all

unnecessary ropes or chains and disable any equipment such as

locks which are not needed for powered operation.

• Do not wear rings, watches or loose clothing while installing or

servicing a garage door operator.

• Ensure ladder is the correct type for the job and is on flat ground.

We recommend the user has 3 points of contact while on ladder.

• Activate the operator only when the garage door is in full view,

free of obstructions and with the operator properly adjusted.

• The operator is not intended for use by young children or infirm

persons without supervision.

• Keep transmitters away from children.

• Do not allow children to play with door controls.

Installation Instructions GDO-12V1 Hiro™5

2. Specifications

Technical Specifications GDO-12V1

Rated voltage range 230V - 240V a.c

Rated frequency 50Hz / 60Hz

Rated power input 150W

Rated operating time: 6 min

Rated operating temperature -10 oC to +55 oC

Rated load 500N

Maximum turns of door drum:

Max door weight:

Maximum door area (wind-lock):

Maximum door area:

Door must be well balanced and able to be operated by hand,

as per warranty conditions and standard AS/NZS 4505:2012

6 turns of the drum wheel

270kg *

22m2 **

28m2

Minimum sideroom 35mm

IP rating IP20

Receiver type Multi-frequency UHF FM

(433.47, 433.92 & 434.37MHz)

Receiver code storage capacity 64 x 4-button Transmitters

Number of code combinations Over 100 billion random codes

Transmitter battery CR2032 (3 Volts)

Courtesy light LED (Light Emitting Diodes)

Please read these important safety rules

These safety alert symbols indicate a personal

safety or property damage instruction exists.

READ THESE INSTRUCTIONS CAREFULLY.

This automatic garage door operator is designed and tested

to offer safe service provided it is installed and operated

in strict accordance with the following safety rules. Failure

to comply with the installation instructions and the safety

warnings may result in death, serious personal injury and/or

property damage.

*: Gross door weight, incl. all fittings

**: Windy conditions can activate the obstruction feature of the opener.

6GDO-12V1 Hiro™Installation Instructions

3. Set Up Requirements

Fig 3.1

3.1 Kit Contents

ITEM DESCRIPTION QTY

1 GDO-12 POWER DRIVE UNIT 1

2 INTERNAL GEAR ADAPTER (FORKS) 3

3 HEX SERRATION HEAD SCREW M6 X 20 6

4 4 BUTTON TRANSMITTERS 2

5 4 BUTTON WALL TRANSMITTER 1

6 LOCKING BAR COVERS 2

GUIDE PACK VR12

7 SCREW-EYE 2

8 PLASTIC WALL PLUG 6.9 X 25 (1”) 2

Installation Instructions GDO-12V1 Hiro™7

4. Pre-Installation Requirements

IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION

Warning: Incorrect installation can lead to severe injury.

Follow ALL installation instructions.

NOTE: Planetary chain equipment must be removed from

the door prior to installation of GDO-12V1 HiRo™.

4.1 Door Operation

The door must be in good operating condition. The maximum

effort to move the door up or down, from stationary, should not

exceed 200 Newtons (20 kg force) at the bottom rail.

Lift the door to about halfway. When released, the door should

stay in place supported entirely by its springs. Raise and lower the

door to check for binding or sticking.

The door may need to be serviced to meet these requirements –

refer to the door manufacturer’s servicing instructions or contact

an authorised dealer.

4.2 Unsuitable Door Types

The fitting of an opener to doors with removable mullions or

doors incorporating a wicket door is not recommended (Fig. 4.1).

4.3 Position

The opener can be installed on either the right or left hand side

of the door (when viewed from inside the garage). The opener is

factory set for right hand side installation.

This opener must be installed in a dry position that is protected

from the weather. Moisture or corrosion damage is not covered

by the Warranty.

4.4 Power Supply

Properly earthed 3 pin single-phase power is required.

WARNING! Using a portable power generator

is not recommended. The opener may appear to

malfunction due to spikes, surges and fluctuations

in the generated voltage.

4.5 Sideroom

The minimum sideroom required from the edge of the door

curtain is 35 mm to the inside of the door bracket, and 80mm to

the wall. If the Battery Backup is to be fitted, at least 130mm to

the bracket is required.

Therefore the recommended sideroom from the edge of the door

curtain is 130mm to the inside of the door bracket, and 170mm

to the wall as per diagram. (Fig. 4.2).

NOTE: The door axle diameter must not exceed 35mm.

4.6 Forks

Attach and secure the three (3) forks 2with the six (6) hex

serration head screws 3to the drive unit 1(Fig. 4.3).All

forks must be used and properly engaged into the drum of the

door for the opener to work effectively.

Fig 4.2

Fig 4.3

Fig 4.1

130mm

80mm 170mm

35mm

Recommended Side roomMinimum Side room

105mm

8GDO-12V1 Hiro™Installation Instructions

5. Opener Safety & Security

MANUAL RELEASE

WARNING! When operating the manual

release (while the door is open) the door

may fall rapidly due to weak or broken

springs, or due to being improperly

balanced.

Do not disengage the operator to manual

operation with children/persons or any

objects including motor vehicles within

the doorway.

TO DISENGAGE:

PULL HANDLE DOWN

& RELEASE

TO RE-ENGAGE:

REPEAT ACTION

PULL

HANDLE

IN THE EVENT THE DOOR BECOMES OBSTRUCTED

DETACH DOOR FROM OPENER AS FOLLOWS:

5.1 The Door CAN NOT be used by the opener when:

a. There is a locking device installed.

b. There is a power failure.

5.2 The Door CAN be used when:

a. There is an emergency, by disengaging the opener.

b. There is a power failure, by disengaging the opener.

5.3 To Disengage the Opener:

a. It is recommended to do so with the door in the closed position.

b. Pull down on the manual release cord, until you hear a click.

c. Move the door manually.

5.4 To Re-Engage the Opener:

a. Check the door has not been locked by a locking device.

b. Pull down on the manual release cord, until you hear a click.

c. The door will now operate from the opener.

CAUTION: When the opener is manually disengaged,

the door is no longer locked. To lock the door manually,

re-engage the opener after the door is closed.

WARNING! Please test the manual release

mechanism to ensure that the manual release is easy

to operate. No more than 20 kg of force should be

required to disengage the door using the manual

release cord. If excessive force is required reset the

close limit position (Section 6.4.3 Resetting Door

Limit Positions).

6. Installation Instructions

IMPORTANT INSTALLATION INSTRUCTIONS.

WARNING - To reduce the risk of severe injury or death:

(1) READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

(2) Install only on a properly operating and balanced garage door. An improperly balanced door has the potential to

inflict severe injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware

before installing the opener.

(3) Remove all pull ropes and remove or make inoperative, all locks connected to the garage door before installing

opener.

(4) Where possible, install the door opener 2.14m or more above the floor. For products having an emergency release,

mount the emergency release 1.83 above the floor and avoiding contact with vehicles to avoid accidental release.

(5) Do NOT connect the opener door operator to source of power until instructed to do so.

(6) Locate the control button:

(i) within sight of door,

(ii) at a minimum height of 1.53m above floors, landings, steps or any other adjacent walking surface so small

children are not able to reach it, and

(iii) away from all moving parts of the door.

(7) Install the Entrapment Warning Label next to the control button in a prominent location. Install the Emergency

Release Label. Attach the marking on or next to the emergency release.

(8) After installing the opener, the door must reverse within 2 seconds when it contacts a 1 1/2 -inch high object (or a 2

by 4 board laid flat) on the floor.

(9) For products having a manual release, instruct the end user on the operation of the manual release. Exception: For

horizontally sliding doors, Item 2 shall be replaced with “Have a qualified service person make repairs and hardware

adjustments before installing the opener.

Installation Instructions GDO-12V1 Hiro™9

6.1.1 Preparation

a. Check the door’s operation:

i. The door must travel smoothly and be easy to operate by hand.

ii. Adjust any tight or twisted guides.

iii. Clean the guides if there is any oil or wax present using a suitable white spirit. The only lubricant suitable for use on

door guides is silicon spray. DO NOT use WD-40, RP-7, petroleum grease, or similar.

b. Fit the weight bar 9and install the locking bar covers 6if there are locking bar holes in the guides.

c. Affix the warning labels supplied with this opener in a prominent place where they are clearly visible.

d. Choose the side where the opener will be installed ensuring there is sufficient sideroom.

Check that the door is still balanced and smooth to operate. If it is not, the door may require servicing (refer to door

manufacturer’s instructions).

6.1 Door Preparation

6.1.2 Pinning the Door to the drum:

Pinning the door’s curtain to its drum maintains security when the opener is

closed. If the curtain is not pinned the door can be partially opened manually.

a. Fully close the door.

b. Mark a minimum of two (2) drill holes on the drum to each end of the door.

c. Drill holes using 3.2mm (1/8”) drill bit.

d. Fit M10 x 32mm screws and washers (not supplied) to each of the four (4)

holes. This screw should be positioned as low as possible in the grove, but

make sure that it does not alter the curtain’s normal lead in to the guide.

BALLOONING DOOR

PINNED DOORFREE DOOR

Pin Points

Screw into the

low part of

grove

10 GDO-12V1 Hiro™Installation Instructions

NOTE - For minimum sideroom installations, the door may have to

be taken down.

Fig 6.2

Tighten U bolts

6.2 Propping the Door

WARNING! The opener must not

be used with a door incorporating a

wicket door.

WARNING! The door and its springs

are under significant tension.

Adjustments should only be carried

out by experienced persons, as

this function can be dangerous if

not performed under strict safety

procedures.

Fig 6.3

6.3.1 Mounting The Opener

a. Check the drive gear rotates freely, by pulling the string handle

down (there will be a click) to disengage opener. Then move the

forks from side to side by hand

b. Slide the opener over the door axle and into the drum of the door

(Fig. 6.3).

c. Ensure the internal gear is pushed in as far as possible (without

interfering with the door curtain) and that the door drum’s wheel

spokes are completely between the opener’s drive forks.

d. Tighten the pipe clamp.

e. Remove the safety rope and door stand or prop.

f. Connect the power cort to a suitable powerpoint, but DO NOT

switch on.

g. Secure the power cord away from any moving object (e.g the door)

with the cable clip supplied.

h. With the opener still disengaged, pull the door up and down to

make sure it runs freely.

NOTE - If the manual release handle is more than 1.8 metres from floor

level when the opener is installed, extend the handle to a height less

than 1.8 metres.

6.2.1 Door prop preparation

a. At the end opposite to where the opener will be fitted, check that

the door axle is tightened to the bracket securely. (Fig. 6.2)

b. Open the door completely and tie safety ropes around the door

roll approximately 300 mm from each end. Do not tie the ropes too

tight as damage to the curtain may ensue.

c. At the end where the opener is to be fitted, support the door with

a safe and suitable lifter.

WARNING! Make sure the door is secure in the support,

is stable and will not move.

d. At the end where the opener will be fitted, use pen to mark the

position of the saddle on the door bracket and the position of the

door bracket on the wall to assist in reassembling.

e. Remove the bolts and saddle from the door bracket.

f. Raise the door off the door bracket and secure in the support.

6.3 Fitting the Opener

NOTE: Use torque of 60Nm

when tightening nuts.

Tabla de contenidos

Otros manuales de Abridor de puerta de garaje de Automatic Technology

Automatic Technology

Automatic Technology Axess Pro Series Manual de usuario

Automatic Technology

Automatic Technology GDO-8 Shed Master Manual de usuario

Automatic Technology

Automatic Technology GDO-7v2 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology Dominator AM800 Manual de usuario

Automatic Technology

Automatic Technology AM-808 Manual de usuario

Automatic Technology

Automatic Technology 62717 Manual de usuario

Automatic Technology

Automatic Technology ATS Series Manual de usuario

Automatic Technology

Automatic Technology GDO-8 ShedMaster Guía del usuario

Automatic Technology

Automatic Technology GDO-9 ENDURO GEN2 Guía de planificación

Automatic Technology

Automatic Technology Smart Phone Control Manual de usuario

Automatic Technology

Automatic Technology GDO-4 EasyRoller Manual de usuario

Automatic Technology

Automatic Technology GDO-8v1 EasyRoller II Manual de usuario

Automatic Technology

Automatic Technology GDO-9v2 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology GDO-11 Ero Manual de usuario

Automatic Technology

Automatic Technology SECURALIFT Guía de inicio rápido

Automatic Technology

Automatic Technology SecuraLift Trio Manual de usuario

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-8V2 EasyRoller II Manual de usuario

Automatic Technology

Automatic Technology Axess Pro Series 1101 Guía de inicio rápido

Automatic Technology

Automatic Technology SecuraLift GDO-9v3 Manual de usuario

Automatic Technology

Automatic Technology SecuraLift GDO-7V1 Guía de inicio rápido

Automatic Technology

Automatic Technology GDO-11v1 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology SecuraLift Rhino Manual de usuario

Automatic Technology

Automatic Technology GDO-6v3 EasyRoller Manual de usuario

Manuales populares de Abridor de puerta de garaje de otras marcas

Dorma

Dorma ES 90 Manual de usuario

Garaga

Garaga SECURITY+ 3265GCM 1HP Manual de usuario

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manual de usuario

Chase Doors

Chase Doors DuraShield Manual de usuario

CSI

CSI Classic Manual de usuario

HATO

HATO 120 Manual de usuario

Chamberlain

Chamberlain Elite 3575S Manual de usuario

Richmond

Richmond GTR156 Manual de usuario

Raynor

Raynor 1280RGD Manual de usuario

CAME

CAME F4000 Series Manual de usuario

B&D

B&D Controll-A-Door 5 Manual de usuario

BFT

BFT PRV AA SL Manual de usuario

Craftsman

Craftsman 139.53924 Manual de usuario

Chamberlain

Chamberlain MyQ 940ESTD Manual de usuario

Westfalia

Westfalia 19 36 07 Manual de usuario

Chamberlain

Chamberlain HD520EVP Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Chamberlain

Chamberlain 8355 - 1/2 hp Manual de usuario