Automatic Technology SecuraLift GDO-7V1 Guía de inicio rápido

GDO-7V1 SecuraLift®

Overhead Garage Door Opener

INSTALLATION INSTRUCTIONS | OWNERS COPY

2GDO-7V1 SecuraLift® Owner Installation Instructions

WARNING: It is vital for the safety of persons to follow all

instructions. Failure to comply with the installation instructions

and the safety warnings may result in serious personal injury

and/or property and remote control opener damage. Please

save these instructions for future reference.

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all

conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of

an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic Technology Australia Pty Ltd hereby further

expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a

result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener

in accordance with these installation instructions.

Owner Installation Instructions GDO-7V1 SecuraLift® 3

Safety Precautions 4

Opener Features 6

Operating Controls 6

Kit Contents 10

Installation 11

Tube Pipe Assembly 11

Determine Door Type 12

Mounting - Track Type Door 12

Using inbuilt antivibration brackets 14

Mounting - Spring Loaded Door 15

Mounting Door Bracket & Arms 16

Easy Access Transmitter 16

Programming the Opener 17

Setting Travel Limits - Control Pane 17

Setting Travel Limits - Transmitter 18

Safety Obstruction Force Test 19

Coding Transmitters 20

Door 20

Courtesy Light 20

Vacation Mode 20

Pet Mode 20

Storing Transmitter From Remote Location 21

Erasing Transmitter Codes 21

Accessories 22

Photo Electric Beam 22

Auto-Close 22

Final Set Up 23

Courtesy Light Time 23

Pet Mode Door Height 23

Transmitter Wall Bracket 23

Re-Initializing 23

Parameters 24

Door Status Indicators 24

System Speciﬁcation 26

Factory Default Settings 26

Trouble Shooting Guide 28

Maintenance Record 29

Parts List 30

Warranty 32

GDO-8V1 SecuraLift®

Overhead Garage Door Opener

4GDO-7V1 SecuraLift® Owner Installation Instructions

CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.

This accessory allows manual operation of the garage door from outside in case of power failure.

For ADDITIONAL SAFETY protection we STRONGLY recommend the ﬁtting of a Photo Electric

Beam. In most countries Photo Electric Beams are mandatory on all garage doors ﬁtted with

automatic openers. For a small additional outlay ATA recommends that Photo Electric Beams be

installed with the automatic opener ensuring additional safety and peace of mind.

DO NOT operate the garage door opener unless the garage door is in full view and free

from objects such as cars and children/people. Make sure that the door has ﬁnished moving

before entering or leaving the garage.

DO NOT operate the garage door opener when children/persons are near the door.

Children must be supervised near the garage door at all times when the door opener

is in use. serious personal injury and/or property damage can result from failure to

follow this warning.

DO NOT allow children to operate the garage door opener. serious personal

injury and/or property damage can result from failure to follow this warning.

Regularly check to make sure that the safety obstruction force is working

correctly, and is tested (by placing a 50mm high object on the ﬂoor)

and set as per the Installation Instructions Manual. Failure to follow the

manual could result in serious personal injury and/or property damage.

This test must be repeated at regular intervals and the necessary

adjustments made as required.

DO NOT disengage the door opener to manual operation with

children/persons or any other objects including motor vehicles

within the doorway.

The door opener is not intended for use by young children

or inﬁrm persons without adequate supervision. Children

should be supervised to ensure that they do not play

with the remote transmitters or the opener.

Keep hands and loose clothing clear of the door

and door opener at all times.

The unit should be installed so that it is protected

from the elements. It should not be exposed

WARNING: It is vital for the safety of persons to follow

all instructions. Failure to comply with the following

Safety Rules may result in serious personal injury and/or

property damage.

Important safety instructions

Owner Installation Instructions GDO-7V1 SecuraLift® 5

to water or rain. It is not to be immersed in water or sprayed directly by a hose or other water carrying device.

The garage door must be well balanced. Sticking or binding doors must be repaired by a qualiﬁed garage

door installer prior to installation of the opener.

Frequently examine the installation, in particular cables, springs and mountings for signs of wear,

damage or imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation

or an incorrectly balanced door may cause injury. DO NOT attempt to repair the door yourself as

hardware is under extreme tension.

Remove or disengage all garage door locks and mechanisms prior to installation of the opener.

Connect the garage door opener to a properly earthed general purpose 240V mains power

outlet installed by a qualiﬁed electrical contractor.

Disconnect the power cord from mains power before making any repairs or removing

covers. Only experienced service personnel should remove covers from the garage

door opener.

When using auto close mode, a photo electric beam must be ﬁtted correctly

and tested for operation at regular intervals. extreme caution is recommended

when using auto close mode. all safety rules must be followed.

In order for the garage door opener to sense an object obstructing the

door way, some force must be exerted on the object. As a result the

object, door and/or person may suffer damage or injury.

If the power supply cord is damaged, it must be replaced by an ATA

service agent or suitably qualiﬁed person.

Make sure that the door is fully open before driving in or out of

the garage and fully closed before leaving the driveway.

Make sure that remote controls are kept out of reach of

children.

Install the wall switch or wall mounted

transmitter in a location where it is out of

reach of children and the garage door is

visible.

Important safety instructions

6GDO-7V1 SecuraLift® Owner Installation Instructions

Operation

To open or close the door simply press the hand held transmitter, the wall mounted

transmitter, or optional wall switch for two seconds. During an open or close cycle

the door can be stopped by pressing the button while the door is in motion. The

next actuation will move the door in the opposite direction.

Hopping code

Every time a transmission is made from the remote transmitter a new security

code is generated. The number of possible code combinations is over 4.29

billion. This greatly enhances the security of the system. Code “grabbing” is made

a thing of the past.

S-alps (semi automatic limits positioning system)

The ALPS system does away with manual adjustment of the doors’ limits position using

mechanical parts, such as cams and micro switches. During installation the hand held

transmitter can be programmed to set the door limits positions.

Anti travel electronic brakes

opener has anti travel electronic brake mechanism which ensure the opener stops the door at

exact location

ISS (intelligent safety obstruction system)

While the door is performing a close cycle, should it hit an obstacle or be restricted in some manner, it will

automatically reverse. The amount of force the door should encounter before reversing is automatically

adjusted by the doors control system during the initial installation of the automatic door opener. The door

will also stop if restricted whilst opening. The Safety Obstruction Force should be checked at least once a

month. See installation manual for instructions.

Security code store

The SecuraLift® Garage Door Opener uses state of the art technology in storing your selected transmitter

security code. Up to 24 different transmitters can be stored in the openers memory.

Features

Thank you for purchasing the ATA SecuraLift® Automatic

Garage Door Opener. This opener is designed to suit

sectional overhead and one piece tilt up doors. The

components and materials used in this opener are of

the latest technology and highest quality. Listed

below are some of the many features.

Owner Installation Instructions GDO-7V1 SecuraLift® 7

Over load indicator

When the maximum opening and closing capacity of the opener is exceeded the red and

green Limits LEDs ﬂash alternately to indicate that an overload has occurred.

Auto courtesy light

The courtesy light on the opener comes on automatically whenever the door is

activated. The light can also be switched on and off without operating the door.

This is done by pressing the button on any hand held or wall mounted transmitter

which has been stored with the light code.The light will stay on for approximately

three minutes then switch off. This time is also adjustable.

Anti vibration brackets

opener has inbuilt antivibration brackets hang the opener by using anti vibration

brackets where noise is the problem.

Vacation mode

A hand held transmitter can be programmed to lock and unlock all other

transmitters that have been programmed into the openers’ memory. The vacation

mode can be used when the door is left idle for long periods of time.

Pet (pedestrian) mode

The hand held transmitter can be programmed to open the door partially so that the

family pet can enter and exit the garage at any time. You may also wish to open the

door to a height suitable only for pedestrian access. The door opening position is also

programmable.

Auto close mode

The opener can be programmed to automatically close after an open cycle. The auto close time

is adjustable. It is compulsory to install a Photo Electric Beam if this mode is selected, otherwise the

door may cause personal injury or damage to property.

Photo electric beam (optional)

The opener has an input for a photo electric beam to be connected for extra safety protection and use of the

auto close mode.

Manual operation

The opener is equipped with a unique manual disengaging device. If the power to the opener is disrupted for

any reason the door can be put into manual mode by pulling down on the string handle on an angle towards

the door. This will allow you to manually open or close the door. To re-engage the opener pull the string

handle away from the door.

Features

8GDO-7V1 SecuraLift® Owner Installation Instructions

Operating controls

P. E. Shunt. The shunt has to be removed when connecting a Photo Electric Beam.

NOTE: P.E. Shunt must not be removed otherwise the opener will not function correctly. Remove only

when a P.E beam is to be connected. PROG INPUT is used for the connection of the ATA Handheld

Programmer for the purpose of editing control and receiver functions.

Terminal Block. 24V PWR is used to power devices such as photo electric beams.

PE (Input) for photo electric beam for safety and auto-close function.

LGT (Input) allow hard wired external trigger for the opener’s courtesy light.

O/S/C INPUT is used for the connection of a wired switch (momentary contact). This switch can then be

used to open, stop or close the door. Install the wall switch in a location where the switch is out of reach

of children and the garage door is visible.

Set button (yellow) is used during the installation phase together with the Open and Close buttons to set

the door limit positions. The Set button is also used to re-initialize the Opener.

Operate button (Yellow) is used during installation to test the open, stop and close cycles for the opener.

The opener has to be initialized by the Reset button before the O/S/C button becomes operable.

Plus (+) button (green) is used during installation to help set the open limit position. Pressing and

holding this button will move the door in the open direction. Movement stops when the button is

released.

NOTE: The open safety obstruction detection is inoperable whenever the Open or Close Drive button is

used to move door.

Open limit led (green) the led is very helpful during installation. It illuminates and ﬂashes when the door

is opening and remains steady on when the open limit position has been reached.

Force margin set Button The obstruction force pressure is set automatically by the opener during

installation. The pressure can be adjusted manually using the Force Margin Set button (White). Holding

the Force Margin Set button and pressing the Plus (+) or Minus (-) button will increase or decrease the

amount of force. The Force Margin Set is only ever used if other environmental factors (wind, etc.) effect

the operations of the door/opener.

Light code button (white) is used for storing or erasing the transmitter button (code) you wish to use to

switch the courtesy light on the opener on or off.

Coding led (red) light ﬂashes when a code is being stored or when a transmitter button is pressed.

Door code button (blue) is used for storing or erasing the transmitter button you wish to use to

command the door to open, stop or close.

Door status LED (Yellow)

Minus (-) button (red) is used during installation to help set the close limit position. Pressing and holding

this button will move the door in the close direction. Movement stops when the button is released.

NOTE: The close safety obstruction detection is inoperable whenever the Open or Close Drive button is

used to move door.

Close limit LED (red) the led is very helpful during installation. It illuminates and ﬂashes when the door is

closing and remains steady on when the close limit position has been reached.

Owner Installation Instructions GDO-7V1 SecuraLift® 9

01 02

03 04 05 06 07

Operating controls

Datum adjust screw is used during limits set up to indicate the mid point of the door’s travel.

Auto close time button (White) is used to adjust the auto close time. While holding in the auto close

button and then pressing the open button the time is increased. Each press will increase the time by 5

seconds. Pressing the close button will decrease the time.

Engage/disengagement cord when pulled down and released this will select manual mode on the

opener, particularly when there is a power failure. Pulling down and again releasing will select automatic

mode on the opener. The length of the string is adjustable.

Easy access transmitter The “manual release” engage/disengagement handle has within its housing a

12 13

10 GDO-7V1 SecuraLift® Owner Installation Instructions

Package contents

GDO-7 Securalift® drive unit 1

Securacode® key ring transmitter pack 1

Pack includes two keyring transmitters two batteries

and one wall mount bracket for ptx4 transmitter

Easy access transmitter - EAT-1 (not available some models) 1

Tubes 5

Tube inserts 4

Pipe support assembly 1

Chain 1

Shuttle assembly 1

Door attachment arms 2

Accessory pack 1

Installation manual 1

Tabla de contenidos

Otros manuales de Abridor de puerta de garaje de Automatic Technology

Automatic Technology

Automatic Technology PA1000V1 Manual de usuario

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manual de usuario

Automatic Technology

Automatic Technology Dominator AM800 Manual de usuario

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-8 ShedMaster Guía del usuario

Automatic Technology

Automatic Technology GDO-8 Shed Master Manual de usuario

Automatic Technology

Automatic Technology GDO-9v2 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-9 ENDURO GEN2 Guía de planificación

Automatic Technology

Automatic Technology GDO-11 Ero Manual de usuario

Automatic Technology

Automatic Technology GDO-8V2 EasyRoller II Manual de usuario

Automatic Technology

Automatic Technology GDO-6v4 EasyRoller Manual de usuario

Automatic Technology

Automatic Technology Axess Pro Series 1101 Manual de usuario

Automatic Technology

Automatic Technology SecuraLift Trio Manual de usuario

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-8 Shed Master Manual de usuario

Automatic Technology

Automatic Technology GDO-6v3 EasyRoller Manual de usuario

Automatic Technology

Automatic Technology Syncro ATS-3 Manual de usuario

Automatic Technology

Automatic Technology 62717 Manual de usuario

Automatic Technology

Automatic Technology GDO-2 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology GDO-10V3L2 Toro Manual de usuario

Automatic Technology

Automatic Technology GDO-11V3 Ero Manual de usuario

Automatic Technology

Automatic Technology SecuraLift GDO-9v3 Manual de usuario

Automatic Technology

Automatic Technology SecuraLift Rhino Manual de usuario

Manuales populares de Abridor de puerta de garaje de otras marcas

Dorma

Dorma ES 90 Manual de usuario

Garaga

Garaga SECURITY+ 3265GCM 1HP Manual de usuario

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manual de usuario

Chase Doors

Chase Doors DuraShield Manual de usuario

CSI

CSI Classic Manual de usuario

HATO

HATO 120 Manual de usuario

Chamberlain

Chamberlain Elite 3575S Manual de usuario

Richmond

Richmond GTR156 Manual de usuario

Raynor

Raynor 1280RGD Manual de usuario

CAME

CAME F4000 Series Manual de usuario

B&D

B&D Controll-A-Door 5 Manual de usuario

BFT

BFT PRV AA SL Manual de usuario

Craftsman

Craftsman 139.53924 Manual de usuario

Chamberlain

Chamberlain MyQ 940ESTD Manual de usuario

Westfalia

Westfalia 19 36 07 Manual de usuario

Chamberlain

Chamberlain HD520EVP Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Chamberlain

Chamberlain 8355 - 1/2 hp Manual de usuario