Automatic Technology SecuraLift Rhino Manual de usuario

SecuraLift® Rhino

AC Overhead Garage Door Opener

INSTALLATION INSTRUCTIONS | OWNER’S COPY

2SecuraLift® Rhino Installation Instructions & Owner’s Manual

WARNING: It is vital for the safety of all persons to

follow these instructions. Failure to comply with the

installation instructions and safety warnings may result

in serious personal injury and/or property damage.

Please save these instructions for future reference.

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all

conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of

an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic Technology Australia Pty Ltd hereby further

expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a

result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener

in accordance with these installation instructions.

Installation Instructions & Owner’s Manual SecuraLift® Rhino 3

SecuraLift® Rhino

Overhead Garage Door Opener

Important Safety Instructions 04

Features 06

Operating Controls 08

Package Contents 10

Installation 11

Knockdown C-Rail Assembly 11

C-Rail Assembly 12

Determine Door Type 13

Mounting on a Track Type Door 14

Mounting on a Non-Track Type Door 15

Mounting Door Bracket & Arms 16

Setting Travel Limits 17

Safety Obstruction Force Test 19

Adjusting Safety Obstruction Force 20

Coding Transmitters 21

Door 21

Courtesy Light 21

Vacation Mode 22

Auxiliary Output 22

Pet (Pedestrian) Mode 23

Erasing Transmitter Codes 23

Mounting Wall Transmitter 23

Accessories 24

Terminal Block 24

Remote Aerial 24

P.E. Beams 25

Electric Key Switch 25

Troubleshooting Guide 26

Default Settings & Speciﬁcations 27

Parameters 28

Maintenance 30

Parts List 32

Warranty 34

4SecuraLift® Rhino Installation Instructions & Owner’s Manual

Important Safety Instructions

CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be

installed. This accessory allows manual operation of the garage door from outside in the event of

power failure.

For additional protection we strongly recommend ﬁtting of Photo Electric (P.E.) Beams.

In most countries P.E. Beams are mandatory on all automated garage doors. For a small

additional outlay Automatic Technology recommends that P.E. Beams be installed with the SecuraLift®

Rhino Overhead Garage Door Opener.

DO NOT operate the SecuraLift® Rhino Overhead Garage Door Opener unless the garage door

is in full view and free from objects such as cars and children/people. Make sure that the door has

ﬁnished moving before entering or leaving the garage.

DO NOT operate the SecuraLift® Rhino Overhead Garage Door Opener when persons are

in or near the doorway. Children near an moving garage door must be supervised at all

times. Serious personal injury and/or property damage can result from failure to follow

this warning.

DO NOT allow children to operate the garage door opener. Serious personal injury

and/or property damage can result from failure to follow this warning.

Regularly check that the safety obstruction force and is tested and set as per

page 19 of this manual. Failure to follow this could result in serious personal

injury and/or property damage. This must be repeated at regular intervals

and adjustments made as required.

DO NOT disengage the SecuraLift® Rhino Overhead Garage Door

Opener to manual operation with persons or any other objects,

including motor vehicles, within the doorway.

The SecuraLift® Rhino Overhead Garage Door Opener is not

intended for use by young children or inﬁrm persons. Children

should be supervised to ensure that they do not play with the

remote transmitters or the opener.

Keep hands and loose clothing clear at all times.

The unit should be installed so that it is protected from

the elements. It should not be exposed to water or

rain, immersed in water or sprayed directly by a

hose or other water carrying device.

WARNING: It is vital for the safety of all persons to follow

all instructions. Failure to comply with the following

safety rules may result in serious personal injury and/or

property damage.

Installation Instructions & Owner’s Manual SecuraLift® Rhino 5

The garage door must be well balanced. Sticking or binding doors must be repaired by a qualiﬁed garage door

installer prior to installation of the SecuraLift® Rhino Overhead Garage Door Opener.

Frequently examine the installation, in particular cables, springs and mountings for signs of wear, damage or

imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation or an incorrectly

balanced door may cause injury. DO NOT attempt to repair the door yourself as hardware is under extreme

tension.

Remove or disengage all garage door locks and mechanisms prior to installation of

the opener.

Connect the SecuraLift® Rhino Overhead Garage Door Opener to a properly earthed general

purpose 240V mains power outlet installed by a qualiﬁed electrical contractor.

Disconnect the power cord from mains power before making any repairs or removing

covers. Only experienced service personnel should remove covers from the SecuraLift®

Rhino Overhead Garage Door Opener.

When using auto-close mode, a P.E. Beam must be ﬁtted correctly and tested for

operation at regular intervals. Extreme caution is recommended when using auto-

close mode. All safety rules must be followed - see page 24 for full details.

In order for the SecuraLift® Rhino Overhead Garage Door Opener to sense an

object obstructing the doorway, some force must be exerted. As a result the

object, door and/or person may suffer damage or injury.

If the power supply cord is damaged, it must be replaced by an Automatic

Technology service agent.

Make sure that the door is fully open before driving in or out of the

garage and fully closed before leaving the driveway.

Make sure that remote controls are kept out of reach of

children.

Install the wall mounted transmitter in a location where it is

out of reach of children and the garage door is visible.

6SecuraLift® Rhino Installation Instructions & Owner’s Manual

Operation

To open or close the door simply press a button on a TrioCode™ handheld

transmitter, or optional wall switch for two seconds. During open and close cycles

the door can be stopped by pressing the button again. The next actuation will

move the reverse the door’s direction.

Powerful 1/2H.P. (0.370kW) Suspended Motor

Powerful enough for even the largest and heaviest of doors, the SecuraLift®

Rhino Overhead Garage Door Opener has a unique internal motor mounting that

reduces vibration, and ultimately operating noise.

Anti-travel electronic brake

The SecuraLift® Rhino Overhead Garage Door Opener features an anti-travel

electronic brake mechanism to ensure the opener stops the door exactly at the set

limit location. This is of particular importance to large and heavy doors which build

up greater momentum when moving.

TrioCode™ Code Hopping Technology

Every time a TrioCode™ transmitter is used a new security code is randomly generated

from over 4.29 billion possibilities. This greatly enhances the security of the system and

makes “code grabbing” a thing of the past

These transmitters also overcome interference issues by simultaneously sending a signal over three

slightly different frequencies. Even if two of the three signals are jammed, the system will still work.

Microswitch Limits

Allows for ﬁne adjustment of set limits via a user-friendly tactile interface.

ISS (Intelligent Safety obstruction System)

While the door is performing a close cycle, should it hit an obstacle or be restricted in some manner, it

will automatically reverse. The amount of force the door should encounter before reversing is automatically

adjusted during the initial installation of the opener. The door will also stop if restricted whilst opening. The

Safety Obstruction Force should be checked at least once a month. See page 19 for instructions.

Features

Thank you for purchasing the SecuraLift® Rhino

Overhead Garage Door Opener. Designed to suit

sectional, overhead and one piece tilt up doors, the

components and materials used ensure this opener

will provide years of smart, simple and secure

operation. Listed below are just some of the

many world leading features:

Installation Instructions & Owner’s Manual SecuraLift® Rhino 7

Security Code Store

The SecuraLift® Rhino Overhead Garage Door Opener will store up to 14 different transmitters

codes.

Overload Indicator

When the maximum opening and closing force capacity of the SecuraLift® Rhino

Overhead Garage Door Opener is exceeded an audible beeper will sound to indicate

that an overload has occurred.

LED Courtesy Light

The SecuraLift® Rhino Overhead Garage Door Opener’s courtesy light illuminates

automatically whenever the door is activated. The light can also be switched on

and off without operating the door by pressing the button on any transmitter

which has been coded to operate the light. The light will stay on for approximately

three minutes then switch off. These LED lights have a super long life and virtually

never require replacement.

Vacation Mode

A transmitter can be coded to block out all other transmitters that have been

programmed into the opener’s memory. Vacation mode is ideal for homes with

non-permanent tenancy or when the door is to be left idle for extended periods.

Pet (Pedestrian) Mode

A transmitter can be programmed to open the door partially so that the family pet can

enter and exit the garage at any time.

Auto-Close Mode

The opener can be programmed to automatically close after an open cycle. It is compulsory

to install P.E. Beams if this mode is selected, otherwise the door may cause personal injury or

damage to property.

Photo Electric (P.E.) Beams (optional)

The opener has an input for a Photo Electric (P.E.) Beam to be connected for extra protection and use of the

auto-close mode.

Manual Operation

The opener is equipped with a manual disengaging device. If power to the SecuraLift® Rhino Overhead Garage

Door Opener is disrupted for any reason, the door can be put into manual mode by pulling down on the string

handle on an angle towards the door. This will allow you to manually open or close the door. To re-engage pull

the string handle away from the door.

8SecuraLift® Rhino Installation Instructions & Owner’s Manual

P.E. Beams Auto-Close Shunt has to be placed on to enable the Auto-Close feature.

PROG INPUT is used to connect the PG-3 Universal Handheld Programmer to edit control and receiver functions.

Terminal Block:

PWR - Used to power devices such as P.E. Beams and external receiver (100 milliamp max).

PE - Used to connect to P.E. Beams.

PE- - A 0 volt connection for P.E. Beams.

COM - A common -ve ground for accessories.

OSC - Used for the connection of a wired switch (momentary contact). This switch can then be used to open,

stop or close the door. Install the wall switch in a location where the switch is out of reach of children

and the garage door is visible.

AUX - Allows the opener to operate other devices such as external lights, or an alarm system.

OPEN LIMIT LED (Green) is used during installation to set the open limit position. It also illuminates and ﬂashes as

the door opens, and remains on when the open limit position has been reached.

CLOSE LIMIT LED (Red) is used during installation to set the close limit position. It also illuminates and ﬂashes as

the door closes, and remains on when the close limit position has been reached.

MINUS (-) button (Red) is used during installation to set the close limit position. Pressing and holding this button

will move the door in the close direction. Movement stops when the button is released. This button is also used for

storing or erasing the transmitter button you wish to use to command the door to open, stop or close.

NOTE: The safety obstruction system is inoperable whenever the MINUS (-) button is used to move the door.

CODE SET LED (Red) ﬂashes when a transmitter button is stored.

LIMIT SET button (Blue) is used during installation, together with the PLUS (+) and MINUS (-) buttons, to set the

door limit positions. The LIMIT SET button is also used to re-initialise the opener.

SERVICE LED (Yellow) indicates when the opener requires service or repairs.

OPERATE button (Blue) is used during installation to test the open, stop and close cycles for the opener. The

OPERATE button can also be used in lieu of a transmitter to activate the opener.,

FORCE MARGIN SET button. The obstruction force margin is set automatically during installation. The margin

can be adjusted manually using the FORCE MARGIN SET button (White). Holding the FORCE MARGIN SET button

and pressing PLUS (+) or MINUS (-) buttons will increase or decrease the amount of force. The FORCE MARGIN SET

button should only be used if environmental factors, such as high winds, affect the door’s operation.

PLUS (+) button (Green) is used during installation to set the open limit position. Pressing and holding this button

will move the door in the open direction. Movement stops when the button is released.

NOTE: The safety obstruction system is inoperable whenever the PLUS (+) button is used to move the door.

Close Limit Adjust Screw is used during installation to ﬁne tune the close limit position.

Open Limit Adjust Screw is used during installation to ﬁne tune the open limit position.

Operating Controls

Installation Instructions & Owner’s Manual SecuraLift® Rhino 9

01 02 03

10 11 12

Operating Controls

13 14

10 SecuraLift® Rhino Installation Instructions & Owner’s Manual

Package contents

Drive Unit

1 x SecuraLift®Rhino drive unit (Fig. 01)

1 x Transmitter pack (Fig. 01)

(Pack includes two keyring transmitters and batteries)

1 x Wall mount transmitter with battery

2 x Door attachment arms (Fig. 01)

1 x Accessory and hardware pack (Fig. 01)

1 x Manual Disengagement Cord (Fig. 01)

1 x Installation Manual

Three Piece Knockdown Track With

Pre-Assembled Chain

IMPORTANT NOTE: If a modiﬁcation to the length of the

track is required, the adjustment must be made from the

drive unit end only.

Single Piece Track With Pre-Assembled

Chain

NOTE: Chain in one piece rail has been tensioned by the

factory. Do not adjust the tension of the chain.

IMPORTANT NOTE: If a modiﬁcation to the length of the

track is required, the adjustment must be made from the

drive unit end only.

PLUS

Fig

Tabla de contenidos

Otros manuales de Abridor de puerta de garaje de Automatic Technology

Automatic Technology

Automatic Technology GDO-11V3 Ero Manual de usuario

Automatic Technology

Automatic Technology GDO-8 ShedMaster Guía del usuario

Automatic Technology

Automatic Technology Smart Phone Control Manual de usuario

Automatic Technology

Automatic Technology GDO-10v1Toro Manual de usuario

Automatic Technology

Automatic Technology iOpener RD40 Manual de usuario

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-6 EasyRoller Manual de usuario

Automatic Technology

Automatic Technology PA1000V1 Manual de usuario

Automatic Technology

Automatic Technology GDO-9 ENDURO GEN2 Guía de planificación

Automatic Technology

Automatic Technology Dominator AM800 Manual de usuario

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-6v4 EasyRoller Manual de usuario

Automatic Technology

Automatic Technology GDO-11v1 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology SecuraLift GDO-7V1 Guía de inicio rápido

Automatic Technology

Automatic Technology Axess Pro Series 1101 Guía de inicio rápido

Automatic Technology

Automatic Technology GDO-2 SecuraLift Manual de usuario

Automatic Technology

Automatic Technology Axess Pro Series Manual de usuario

Automatic Technology

Automatic Technology GDO-10v1 Toro Manual de usuario

Automatic Technology

Automatic Technology 62717 Manual de usuario

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Manual de usuario

Automatic Technology

Automatic Technology GDO-2 SecuraLife Manual de usuario

Automatic Technology

Automatic Technology Axess Pro Series 1101 Manual de usuario

Automatic Technology

Automatic Technology GDO-10V3L2 Toro Manual de usuario

Automatic Technology

Automatic Technology SecuraLift Trio Manual de usuario

Manuales populares de Abridor de puerta de garaje de otras marcas

Dorma

Dorma ES 90 Manual de usuario

Garaga

Garaga SECURITY+ 3265GCM 1HP Manual de usuario

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manual de usuario

Chase Doors

Chase Doors DuraShield Manual de usuario

CSI

CSI Classic Manual de usuario

HATO

HATO 120 Manual de usuario

Chamberlain

Chamberlain Elite 3575S Manual de usuario

Richmond

Richmond GTR156 Manual de usuario

Raynor

Raynor 1280RGD Manual de usuario

CAME

CAME F4000 Series Manual de usuario

B&D

B&D Controll-A-Door 5 Manual de usuario

BFT

BFT PRV AA SL Manual de usuario

Craftsman

Craftsman 139.53924 Manual de usuario

Chamberlain

Chamberlain MyQ 940ESTD Manual de usuario

Westfalia

Westfalia 19 36 07 Manual de usuario

Chamberlain

Chamberlain HD520EVP Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Chamberlain

Chamberlain 8355 - 1/2 hp Manual de usuario