Audiovox VOH703 Manual de usuario

128-6423

1 of 16

VOH704

ELECTRONICS CORP.

VOH703

Drop Down

TV/Video

Monitor

OWNER’SWNER’S

WNER’SWNER’S

WNER’S

MANUMANU

MANUALAL

ALAL

-2-

128-6423

2 of 16

Important Notice

It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped

with a television viewer or screen that is located in the motor vehicle at any point forward of

thebackofthedriver’sseat,orthatisvisible,directlyorindirectly,tothedriverwhileoperating

the vehicle. In the interest of safety, the VOH703 should never be installed where it will be

visible, directly or indirectly, by the operator of the motor vehicle.

WARNINGS

Do not use any solvents or cleaning materials when cleaning the video system.

Do not use any abrasive cleaners, they may scratch the screen. Use only a lightly

dampened lint free cloth to wipe the screen if it is dirty.

Lock the LCD screen in the fully closed position when not in use.

Before putting on headphones always adjust the volume setting to the lowest position.

Remember to leave the dome light switch in the off or auto positions when the vehicle

is unattended, as the dome lights, if left on, can drain the vehicle’s battery.

Do not put pressure on the screen.

Donot allow children totouch or scratch thescreen, as it maybecome dirty or damaged.

Safety Precaution

For safety reasons, when changing video tapes it is recommended that the vehicle is not in

motion and that you do not allow children to unfasten seatbelts to change tapes or make any

adjustments to the system. System adjustments can be accomplished using the remote

controlunit, while seatbelts remainfastened. Enjoy your Audiovoxentertainmentsystem but

remember-safety of all passengers remains the number one priority.

-3-

128-6423

3 of 16

Congratulations on your purchase of the Audiovox

VOH703drop-downTV/VideoMonitor. TheVOH703

has been designed to give you and your family many

yearsofvideoentertainment in a mobileenvironment.

Please read the directions that follow to familiarize

yourselfwiththeproductandto ensure that you obtain

the best results from your equipment.

Please note: Installation options vary, see the

individual owner’s manuals for each component in

your system to obtain a full understanding of each

component’s operation.

Features

7” TFT(Thin Film Transistor)Active Matrix LCD

(Liquid Crystal Display) Monitor (4:3 and 16:9

AspectRatio)

OSD (On Screen Display) for Control of Picture

QualityandFunctions

FullFunctionRemoteControl

TelevisionTuner

TwoAudio/VideoSources(inputs)

Headphone/SpeakerAmplifier

HeadphoneJacks(TV)

ForwardandSideRemoteSensor

DomeLightswithSwitch

BacklitControlsforLowLightOperation

Television Reception

This entertainment system is designed primarily for

viewing prerecorded movies or playing video games.

Televisionreception in amovingvehicle will be limited

and in some areas will not be possible due to weak

and variable signal strength. Television viewing in a

stationary vehicle will result in an improvement, but

maystill bemarginalduetosignal strength. Thequality

of the picture will not be consistent with home TV

reception. Reception may be affected by weather

and distance from TV station. A weak signal may

cause the picture to roll, be snowy, or cause some

color loss.

-4-

128-6423

4 of 16

-5-

128-6423

5 of 16

Front Panel

1. Dual Channel Infrared Transmitter – Used to

transmit audio to wireless headphones.

TV/Video Controls

2. Power Button – Bright red when system is On,

dim when Off.

3. Screen Select – Used to select between 4:3 or

16:9 screen viewing aspect ratio.

4. Channel Up/Down – Changes the TV channel.

5. Volume Up/Down – Controls volume to

headphonejack (TV EAR)and external speakers

if connected.

6. Auto Program – Used to program local channels

into the TV memory.

7. Source Select – Used to selectA/V sources (TV,

VCP, DVD or Game).

8A.Forward Sensor Eye – Allows the remote control

to operate the VOH703’s OSD (On Screen

Display),controlvolumetowiredheadphonejacks

(and optional external speakers), and to control

theVideo Cassette Player andotheraccessories.

8B.Side Remote Sensor Eye – Allows the remote

controltooperatethe VOH703’s OSD (On Screen

Display),controlvolumetowiredheadphonejacks

(and optional external speakers), and to control

theVideo Cassette Player andotheraccessories.

9. Three position Dome Light Switch

• Auto – Automatically switches on the dome

lights in conjunction with the vehicle’s interior

illumination.

• Off – Turns off dome lights and prevents them

from lighting when the switch is in the off

position.

• On – Turns on the dome lights.

10. Dome lights – provide additional interior vehicle

illumination.

11. Screen Release – Slides in the direction of the

arrow to release the drop down screen.

12. TV EAR Jack-Headphone Jack – Allows plug-in

of wired headphones with 1/8” stereo plug for

monitoring the video program audio.

NOTE: Audiovox recommends the use of the

AudiovoxHP275 Headphones.

-6-

128-6423

6 of 16

BATTERY INSTALLATION

Before attempting to operate your Remote Control,

install the batteries as described below.

1) Turnthe Remote Control face down. Press down

onthe ridged areaof the batterycover and slideit

off.

2) Install two “AAA” batteries as shown. Make sure

that proper polarity (+ or -) is observed.

3) Slide the cover back until it clicks.

Theremote control will operate theVOH703,Audiovox

Televisions and Video Cassette Players. It is not a

universalremote control and will not control equipment

from other manufacturers.

If a universal remote control is to be used with the

VOH703, choose the remote encoding scheme for

AudiovoxTelevisionswhenprogramming the remote.

REMOTE CONTROL OPERATION

TV/VIDEO MUTE

VOL

PICTURE

3CH2

WRITE

ERASE/ AUTO

PROGRAM

PAUSE

PLAY

STOP

SELECT VOL

1--

SKIP/

REW

FFWD

REPLAY

MEMORY

-7-

128-6423

7 of 16

Remote Controlled TV/Monitor

Functions

1. POWER ON/OFF

Press this button to turn the VOH703 On. The

channel number or current video source will be

displayedonscreen and thepicturewill appear in a

few seconds. Press the button again to turn the

VOH703Off.

2. DIRECT ACCESS (O-9) BUTTONS

Use these buttons to make a direct channel

selection. The channel number chosen will be

displayed on the screen for about 4 seconds. The

direct access is carried out with 0-9 keys (0-69ch).

3. CHANNEL UP/DOWN BUTTONS

Use these buttons to advance to the next higher or

lower channel. See also: SKIP / SEARCH

BUTTON.

4. VOLUME UP/DOWN BUTTONS

Use these buttons to increase or decrease the

volume level of the headphone jacks or external

speaker if installed. They are also used to make

picture adjustments in picture select mode.

Note: These buttons will not affect the volume of

wired RF modulator.

5. PICTURE SELECT BUTTON

Each time this button is pressed, the on screen

picture adjustment display cycles through

“adjustment bars” for CONTRAST,

BRIGHTNESS, COLOR and TINT. Once the

desired adjustment bar is displayed, use the

VOLUMEUP/DOWNbuttonstoadjust the setting.

The display will automatically turn off if no

adjustments are made within 6 seconds, or if any

other button is depressed.

6. MUTE BUTTON

Press this button to remove the sound at the

headphone stations. The screen will display the

volume adjustment bar for 6 seconds, indicating

that the sound has been turned off. Pressing the

button again restores sound to the previously set

level. The mute feature may also be released by

pressing the VOLUME UP/DOWN BUTTONS.

7. TV/VIDEO BUTTON

Any video equipment connected to the AUDIO/

VIDEO inputs can be viewed with the TV by

pressing

this button. Each time the button is pressed, the

Audio / Video source will change in the following

sequence VIDEO 1, VIDEO 2 and TV.

8. AUTO MEMORY BUTTON

When the AUTO MEMORY button is pressed, all

channels in TV or CATV mode are searched and

tuned; all the channels with signals detected are

automatically stored. Please refer to page 2 for

more information on TV reception.

-8-

128-6423

8 of 16

9. SKIP/SEARCH BUTTON

This button selects between SKIP and SEARCH

mode. In “SKIP mode” the TV only stops on

channelsthatareprogrammed into memory when

the CHANNEL UP/DOWN buttons are used.

When the SKIP mode is off, the TV will stop on

all active channels.

10. ERASE/WRITE BUTTON

Whentunedtoachannel press this button tostore

or erase the channel from memory. The stored

channel numbers are displayed in “GREEN” on

the screen and the non-stored channel numbers

are in “RED”. When the skip mode is on, the

VOH703will tune toonlythestoredchannelswhen

using the CHANNEL UP/DOWN buttons.

Remote Controlled VCP Functions

These features can only be used with an Audiovox

VideoCassette Player,if this optionwasinstalledwith

your video package.

11. POWER BUTTON

This button is used to turn the VCP on and

off.

12. “REW” REWIND BUTTON

If this button is pushed while the tape is stopped,

thetape will rewind. If this buttonis pushed while

the tape is playing, the VCP will go into rewind

search mode. For more information consult the

Audiovox VCP Owner’s Manual.

13. PLAY BUTTON

Press this button to activate play mode while a

tapeis loaded into the VCP. Thisbutton may also

be used to disengage search and pause modes.

For more information, consult the VCP owner’s

manual.

14. “F.FWD.” FAST FORWARD BUTTON

If this button is pushed while the tape is stopped,

tapewillfastforward. Ifthisbutton is pushed while

thetape is playing, the VCPwillgointofastforward

search mode. For more information on the

search feature of the VCP, consult the VCP

owner’s manual.

15. REPLAY BUTTON

Pressing this button will rewind tape and

immediatelybegin playback when thetape is fully

rewound.

16. STOP BUTTON

Press this button to stop the tape.

-9-

128-6423

9 of 16

CHANNEL SET UP

In order to easily access all available TV channels, it

may be necessary to perform channel auto-

programming whenever the vehicle’s geographic

locationhaschanged,i.e.citytocity,weak signal area.

1. Pressthe AUTOMEMORY button on theRemote

Control Unit or the AUTO PROGRAM button on

the drop down video unit. You will see the TV

cycle through all its channels. The built-in

microprocessor will automatically note each

channelthat is actively broadcastingin your area.

2. (A) To tune only strong clear channels with the

CHANNEL UP/DOWN buttons, press the SKIP/

SEARCH button on the Remote Control until

“SKIP MODE ON” is displayed on the bottom of

the screen. In this mode the TV will tune only to

strong active channels when the UP or DOWN

buttonsareusedon the monitor or remotecontrol.

3. (B) To tune weak or marginal channels with the

CHANNEL UP/DOWN buttons , press the SKIP/

SEARCH button on the Remote Control until

“SKIP MODE OFF” is displayed on the bottom of

the screen. Tune to the desired channel using

the CHANNEL UP/DOWN buttons or go directly

to the channel by using the 0-9 buttons on the

Remote Control.

4. To ERASE a channel, press the ERASE/WRITE

buttononthe Remote Control Unituntil“MANUAL

MEMORY XX ERASE” is displayed on screen.

To STORE a channel, press the button until the

MANUAL MEMORY XX ADD is displayed on

screen.

Note : Please refer topage 3 formore information on

TV reception.

Turning the VOH703 On or Off

1. Sliding the screen release lock forward will unlock

theLCDscreencausing it to dropdownslightly.Pivot

the screen downward until a comfortable viewing

angle is reached. The internal friction will hold the

screen in position while the system is in use.

2. Pressingthepowerbuttonontheunitortheremote

control will turn the system on or off alternately.

When in use the internal backlighting will illuminate

the controls.

3. After the unit has been turned on and the picture is

displayed, adjust the viewing angle, by pivoting the

screen to optimize the picture quality.

4. Remember to turn the unit off and return the LCD

displayback to thelockedpositionwhen notinuse.

-10-

128-6423

10 of 16

Operation

Overhead Dome Lights

The lights integrated into the VOH703 are controlled

by a three position slide switch. Sliding the switch to

the on position will turn the lights on. The off position

willprevent the lights from turning on at alltimes and

theauto position willallow the lights to turn on and off

with the vehicle’s interior lighting. Do not leave the

vehicle unattended with the dome light switch in the

onposition,asthiscouldresultinadischargedbattery.

Remote Sensor

The VOH703 incorporates an Infrared sensor which

relays signals from the remote control to allow the

VOH703and VCP tobe controlled simply by pointing

its remote control at the remote sensor eye. This

provides control of auxiliary equipment such as an

AudiovoxVideoCassette Player. Theinfrared sensor

can relay signals from any manufacturer’s remote

controls to the component connected to the Video 1

and 2 inputs, such as a DVD player. In this case you

must use the remote control supplied with the DVD

player.

Dome

Light

Switch

Remote

Sensor Eye

Infrared

Transmitters

Remote

Sensor Eye

Otros manuales para VOH703

Tabla de contenidos

Otros manuales de Sistema de vídeo para coche de Audiovox

Audiovox

Audiovox VE926 - VE - 926 Manual de usuario

Audiovox

Audiovox 1181279 Manual de usuario

Audiovox

Audiovox MMD 70 Guía de inicio rápido

Audiovox

Audiovox VODDLX10 Manual de usuario

Audiovox

Audiovox AVXMTG13UA Manual de usuario

Audiovox

Audiovox Mobile Video 128-8770 Manual de usuario

Audiovox

Audiovox 1187001PL Manual de usuario

Audiovox

Audiovox HR7008PKG Manual de usuario

Audiovox

Audiovox 50-0300A-002 SERIES Manual de usuario

Audiovox

Audiovox PROV716 Manual de usuario

Audiovox

Audiovox VOD1048 Manual de usuario

Audiovox

Audiovox VOD8521 - DVD Player / LCD Monitor Manual de usuario

Audiovox

Audiovox VODDLX10 Manual de usuario

Audiovox

Audiovox VE640 - VE - 640 Manual de usuario

Audiovox

Audiovox VOD1021 Manual de usuario

Audiovox

Audiovox 1187025 Manual de usuario

Audiovox

Audiovox VME 9309 TS Manual de usuario

Audiovox

Audiovox VOH683 Manual de usuario

Audiovox

Audiovox MMD85 - 8.5 Inch Dropdown Video Monitor Manual de usuario

Audiovox

Audiovox LCM7020PKG Manual de usuario

Audiovox

Audiovox VOD10 - Car - Overhead LCD Monitor Manual de usuario

Audiovox

Audiovox MM92HR Manual de usuario

Audiovox

Audiovox Mobile Video 128-8342 Manual de usuario

Audiovox

Audiovox AVT 1498 Manual de usuario

Manuales populares de Sistema de vídeo para coche de otras marcas

Stinger

Stinger HEIGH10 RB10RAM13B Manual de usuario

Eonon

Eonon E1057 Manual de usuario

Milion

Milion D2223 Manual de usuario

Metra Electronics

Metra Electronics 99-8153 Manual de usuario

Voxx Electronics

Voxx Electronics HR8MA1 Manual de usuario

Axxera

Axxera AV604Bi Manual de usuario

Clarion

Clarion NX706E Manual de usuario

Pyle view

Pyle view PLDN74BTi Manual de usuario

Clarion

Clarion NX602 Manual de usuario

PowerAcoustik

PowerAcoustik PTID-5850N Manual de usuario

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Guía del usuario

Lanzar

Lanzar SVDVD5 Manual de usuario

Kia

Kia MTXM100YPPE Manual de usuario

Eonon

Eonon E1060 Manual de usuario

Macrom

Macrom M-AN900 Manual de usuario

Hyundai

Hyundai BAPE-L3000N Manual de usuario

r.LiNK

r.LiNK RL2-UCON8-SM Manual de usuario

Blaupunkt

Blaupunkt DVP 01C Manual de usuario