AudioCodes Mediant 500Li MSBR Manual de usuario

1 |Page

Mediant™ 500Li

Analog VoIP Gateway

Quick Setup Guide

Welcome

Thank you for choosing AudioCodes’ Mediant 500Li Analog VoIP Gateway.

This document is intended to provide basic instructions for initial setup of the Mediant 500Li (hereafter,

referred to as device) and connecting it to your network. For advanced configuration, please refer to the

device's Configuration Notes and Hardware Manual respectively, which can be downloaded from AudioCodes

Website at https://www.audiocodes.com/library/technical-documents.

Before you begin, please read the Safety Precautions and the Regulatory Information document.

2 |Page

Safety Precautions

This device is an indoor unit and therefore, must not be installed outdoors.

Ethernet cabling must be routed only indoors and must not exit the building.

Do not open or dismantle the device.

Do not expose the device to water or moisture.

Make sure the device is installed in a well-ventilated location to avoid over heating of internal

components and subsequent damage.

Do not place any object on top of the device and make sure that sufficient clearance from the top and

sides are maintained to ensure proper airflow to avoid over heating of internal components.

Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).

Use only the supplied AC/DC power adapter for connection to the power source.

In case of a malfunction, do not attempt to fix the power adapter and do not use any other type of

power adapter.

Package Contents

Make sure that the following items (in addition to any separate-orderable items that you may have purchased)

are included with your shipped device:

4 x anti-slide bumpers for desktop mounting

1 x AC/DC power adapter

Regulatory Information document

This Quick Guide

3 |Page

Physical Description of Front Panel

Power

LED indicating power status:

Green On

Power received by device.

Off

No power.

Status

LED indicating operating status:

Green On

Device is operational.

Green Flashing

Initial rebooting stage or software upgrade in process.

Red On

Boot failure.

Off

Advanced rebooting stage.

WAN GE

LED indicating Giga Etgernet WAN link status:

Green On

WAN GE link established.

Green Flashing

Data received or transmitted.

Off

No WAN GE link or power not received by the device.

4 |Page

Physical Description of Rear Panel

POWER

DC power plug entry for external AC/DC power adapter.

ON / OFF

Power button to switch on (pressed in) and off (pressed out) the device.

CONSOLE

RJ-45 port for RS-232 serial communication with the device.

Reset pinhole button for resetting the device or restoring it to factory defaults. To

restore to factory defaults: with a paper clip or any other similar pointed object, press

and hold down the button for at least 12 seconds (but no more than 25 seconds).

Please note that the device will lose all its configuration!

S0 / WAN

WAN interface port Giga Ethernet (10/100/1000Base-T)

Green On

Ethernet link established.

Green Flashing

Data is received or transmitted.

Off

No Ethernet link.

S1 / FXS

S2 / FXS

S1: Ports 1-4 of analog interface (FXS).

S2: Ports 5-8 of analog interface (FXS).

5 |Page

Mounting the Device

You can mount the device in several ways:

Placing it on a desktop using the four anti-slide bumpers (supplied), which you need to stick on the

grooves located on the underside of the device. The bumpers avoid involuntary movement of the unit

on the desktop as well as enable better air flow for cooling the device.

Mounting it in a standard 19-inch rack by placing it on AudioCodes 1U 19-inch rack mount shelf

(separate orderable item). The procedure includes attaching the shelf to the rack's front posts, and

then placing the device on the shelf where it is securely held in position by the device's anti-slide

bumpers which fit into the shelf's four square-openings.

Mounting it on a wall, using the integral mounting keyholes located on its underside.

6 |Page

Assigning an IP Address

You can manually assign a static IP address to the device or you can use a DHCP server to dynamically assign an

IP address to the device. This is configured through the device's Command-Line Interface (CLI).

To assign an IP address:

1. Connect the device's RS-232 serial port, located on the rear panel and labeled CONSOLE, to the serial

communication port on your computer (serial cable is not supplied).

2. Insert the DC plug, located at the end of the power cord of the supplied AC/DC power adapter, into the

device's power socket located on the rear panel and labeled POWER. Plug the power adapter directly

into a standard electrical wall outlet. Switch on the device by pressing-in the ON/OFF power button

located next to the socket. The Power LED on the front panel should turn on (green).

7 |Page

3. Establish serial communication with the device, using a terminal emulator program such as

HyperTerminal or putty, with the following communication port settings:

Baud Rate: 115,200 bps

Data Bits: 8

Parity: None

Stop Bits: 1

Flow Control: None

4. At the device's CLI prompt, type the username (default is Admin), and then press Enter:

Username: Admin

5. At the prompt, type the password (default is Admin), and then press Enter:

Password: Admin

6. At the prompt, type the following, and then press Enter:

enable

7. At the prompt, type the password of the Privileged User command mode (default is Admin), and then

press Enter:

Password: Admin

8. At the #prompt, type the following to access the data-routing menu, and then press Enter:

# configure data

(config-data)#

9. At the prompt, type the following to access the Gigabit Ethernet port interface, and then press Enter:

(config-data)# interface gigabitethernet 0/0

(conf-if-GE 0/0)#

8 |Page

10. To assign a static IP address, run the following commands:

(conf-if-GE 0/0)# ip address <IP Address> <Subnet Mask>

(conf-if-GE 0/0)# exit

(config-data)# ip route 0.0.0.0 0.0.0.0 <Default Gateway> gigabitethernet 0/0

(config-data)# do write

(config-data)# exit

11. To obtain an IP address from a DHCP server, run the following commands:

(conf-if-GE 0/0)# ip address dhcp

(conf-if-GE 0/0)# ip dhcp-client default-route

(conf-if-GE 0/0)# ip dns server auto

(conf-if-GE 0/0)# do write

(conf-if-GE 0/0)# exit

(config-data)# exit

9 |Page

Cabling the Device

Cabling depends on your ordered hardware interfaces, for example, the type of WAN interface.

1. Connect the device's WAN port interface to your router.

2. Connect any phone, fax or other PSTN equipment to any of the analog port interfaces (FXS).

3. Insert the DC plug that is located at the end of the power cord of the supplied power adapter into the

device's power socket located on the rear panel and labeled POWER. Plug the power adapter directly

into a standard electrical wall outlet. Switch on the device by pressing-in the power button located on

the rear panel. When the device receives power, the Power LED turns on (green).

4. You should now be able to make and receive calls, based on your local plan with your service provider.

10 |Page

MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your

Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice, AudioCodes Meeting Insights, AudioCodes Room Experience

and CloudBond are trademarks or registered trademarks of AudioCodes Limited. All other products or trademarks are

property of their respective owners. Product specifications are subject to change without notice.

International Headquarters

1 Hayarden Street,

Airport City

Lod 7019900, Israel

Tel: +972-3-976-4000

Fax: +972-3-976-4040

AudioCodes Inc.

200 Cottontail Lane,

Suite A101E,

Somerset, NJ 08873

Tel: +1-732-469-0880

Fax: +1-732-469-2298

Website: https://www.audiocodes.com

Document #: LTRT-13942

Date Published: 13/04/2021

Otros manuales para Mediant 500Li MSBR

Tabla de contenidos

Otros manuales de Puerta de AudioCodes

AudioCodes

AudioCodes Mediant 500Li MSBR Manual de usuario

AudioCodes

AudioCodes Mediapack mp-11x Manual de usuario

AudioCodes

AudioCodes Mediant 1000 Manual de usuario

AudioCodes

AudioCodes MediaPack 1288 Manual de usuario

AudioCodes

AudioCodes MediaPack Series Instrucciones de montaje

AudioCodes

AudioCodes MediaPack MP-124 Manual de usuario

AudioCodes

AudioCodes MediaPack MP-402 Manual de usuario

AudioCodes

AudioCodes MediaPack MP-11x Series Manual de usuario

AudioCodes

AudioCodes MP-204 Manual de usuario

AudioCodes

AudioCodes MP-252 Manual de usuario

AudioCodes

AudioCodes E-SBC Manual de usuario

AudioCodes

AudioCodes Mediant 800 MSBG Manual de usuario

AudioCodes

AudioCodes Mediant 2000 Manual de usuario

AudioCodes

AudioCodes MP-100 Manual de usuario

AudioCodes

AudioCodes Mediant 1000B Manual de usuario

AudioCodes

AudioCodes mediapack MP-500 Manual de usuario

AudioCodes

AudioCodes Mediant 800B Manual de usuario

AudioCodes

AudioCodes Mediant 4000 SBC Manual de usuario

AudioCodes

AudioCodes Mediant 500 E-SBC Manual de usuario

AudioCodes

AudioCodes MP-272-DB Manual de usuario

AudioCodes

AudioCodes Mediant 800B Manual de usuario

AudioCodes

AudioCodes MP-26 series Manual de usuario

AudioCodes

AudioCodes Mediant 1000B Manual de usuario

AudioCodes

AudioCodes Mediant 800 Instrucciones de montaje

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario