ATN ThOR-HD 384 2 - 8x Manual de usuario

ThOR-HD Series

THERMAL SMART HD RIFLESCOPE

MANUAL

THOR-HD USER’S GUIDE (REV. 4, AUGUST, 2017)

AMERICAN

TECHNOLOGIES

NETWORK

CORP.

THIS PRODUCT CONTAINS NATURAL RUBBER LATEX, WHICH MAY CAUSE ALLERGIC REACTIONS

CAUTION!

The instructions in this manual are for informational use only and subject to change without notice,

this manual is not to be construed as a commitment by ATN Corp.

ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.

PICATINNY RAIL

DIOPTER

ADJUSTMENT RING

MOUNTING SYSTEM

POWER BUTTON

FOCUS

ADJUSTMENT RING

BATTERY

HOUSING CAP

START/STOP

VIDEO RECORDING

ENTER BUTTON

TAKE A PICTURE

ZOOM IN

ZOOM OUT

MICROSD,

MICRO HDMI

& MICRO USB

TABLE OF CONTENTS

FEATURES ....................................4

APPLICATION .................................4

SPECIFICATIONS ..............................5

PREPARING THE DEVICE .......................7

Unpacking .................................7

Installation of batteries........................7

MicroSD, USB and HDMI ports .................7

Firmware update ............................8

ON/OFF...................................9

Using keypad...............................9

Focusing ..................................9

Mounting your scope ........................10

Compass calibration ........................10

INTERFACE ..................................11

Homescreen ..............................11

Main operations ............................12

Shortcut carousel ..........................13

Using System Settings.......................14

FUNCTIONS..................................16

Photo modes ..............................16

Recoil Activated video .......................17

Rangefinder...............................19

Zeroing ..................................21

Ballistic Calculator ..........................22

How to perform a NUC.......................26

Pixel Correction Procedure ...................26

Reticle style adjustment......................27

SYSTEM SETTINGS .......................... 28

Thermal ..................................28

Photo/Video...............................28

Display...................................29

Profiles/Zero ..............................29

Settings ..................................30

SERVICING ..................................31

Warnings and cautions ......................31

MOBILE APPLICATIONS .......................31

FEATURES

RECORD HD VIDEO BALLISTIC CALCULATOR

WiFi OBSIDIAN USER INTERFACE

SMOOTH ZOOM BLUETOOTH

E-COMPASS 3D GYROSCOPE

SMART RANGE FINDER RECOIL ACTIVATED VIDEO (RAV)

APPLICATION

The most technologically advanced line of thermal rifle scopes on the

market, bar none! The all new Obsidian “T” II Thermal Core is at the heart of

all ATN systems. This technology helped ATN to continue to make bigger and

better updates to its award winning thermal product line.

Record videos and photos onto a microSD card. Never again forget to

record that perfect shot with ATN’s patented RAV (Recoil Activated Video).

Use ATN’s Smart Range Finder to quickly range in on your target and allow

the ballistic calculator to make instantaneous corrections to your POI (Point

of Interest) on the fly. Plus, take advantage of the additional features and

sensors packed into these incredible systems, such as; Smooth Zoom, built

in Wi-Fi, Bluetooth, 3D Gyroscope, 3D Accelerometer and 3D Magnetometer.

SPECIFICATIONS

ThOR-HD 384

1.25 - 5x

ThOR-HD 384

2 - 8x

ThOR-HD 384

4.5 - 18x

ThOR-HD 384

9 - 36x

ThOR-HD 640

1 - 10x

ThOR-HD 640

1.5 - 15x

ThOR-HD 640

2.5 - 25x

ThOR-HD 640

5 - 50x

Item # TIWSTH381A TIWSTH382A TIWSTH384A TIWSTH389A TIWSTH641A TIWSTH642A TIWSTH643A TIWSTH645A

Sensor 384×288 640×480

Magniﬁcation 1.25 - 5x 2 – 8× 4.5 – 18× 9 – 36× 1 – 10× 1.5 – 15× 2.5 – 25× 5 – 50×

Angle of view 16×12.5 12×9.5 6×4.7 3×2.4 32×25 24×19 12.5×9.7 6×4.7

Objective lens focal length 19 mm 25 mm 50 mm 100 mm 19 mm 25 mm 50 mm 100 mm

Micro Display HD Display

Core ATN Obsidian “T” II

Eye relief 65 mm

Waterproof rating / IP rating Weather resistant

Video Record Resolution 1280×960 @ 30 fps

Microphone Yes

MicroSD card Up to 64 GB

Micro USB Yes

Micro HDMI Yes

WiFi (Streaming, Gallery,

& Controls) iOS & Android

Bluetooth 4.1

GPS (Geotagging, Elevation, etc.)

Yes

ThOR-HD 384

1.25 - 5x

ThOR-HD 384

2 - 8x

ThOR-HD 384

4.5 - 18x

ThOR-HD 384

9 - 36x

ThOR-HD 640

1 - 10x

ThOR-HD 640

1.5 - 15x

ThOR-HD 640

2.5 - 25x

ThOR-HD 640

5 - 50x

3D Gyroscope Yes, GS7

3D Accelerometer Yes

3D Magnetometer Yes

Range Finder Yes

Ballistic Calculator Yes

RAV (Recoil Activated Video) Yes

Electronic Compass Yes

Smooth Zoom Yes

Reticles Multiple Patterns & Color Options

Mount Two fixing

screws mount Picatinny Quick Release Mount, Interchangeable

Compatible mounts A.R.M.S.® #17® (single lever), A.R.M.S.® #35® (double lever), LaRue LT270, American Defense (AD-170)

Battery life (Li-ion) 8 hr

Battery type (4) AA (Lithium Recommended)

Dimensions

6.85”×3.16”×3.14”

174×80.26×80 mm

8.81”×3.16”×3.14”

224×80.26×80 mm

10.67”×3.97”×3.47”

271×101×88 mm

6.85”×3.16”×3.14”

174×80.26×80 mm

8.81” x 3.16” x 3.14”

224×80.26×80 mm

10.67”×3.97”×3.47”

271×101×88 mm

Weight 1.55 lb / 0.68 kg 1.85 lb / 0.84 kg 2.75 lb / 1.24 kg 1.55 lb / 0.68 kg 1.85 lb / 0.84 kg 2.75 lb / 1.24 kg

Warranty 3 years

Human Detection Range 625 800 1500 2500 625 800 1500 2500

Human Recognition Range 280 400 600 1100 280 400 600 1100

Human Identiﬁcation Range 170 250 360 600 170 250 360 600

* ATN reserves the right to change the above specifications at any time without notice

PREPARING THE DEVICE

UNPACKING

The following steps must be performed prior to use:

1. Open packaging box, remove ThOR-HD and check the contents.

• ATN Help Card

• ATN Thor-HD

• Battery Lifetime Information and Power Kit Card

• FB Group and ATN Forum Card

• Firmware Update and Review Card

• Black Nylon Case

• Thor HD Manual

• Thor HD Quick Start Guide Card

2. Make sure that nothing is missing.

3. Inspect the device for damage to optical surfaces, body, eyecups, opera-

tion buttons, etc.

4. Ensure that all optical surfaces are clean and ready for use.

NOTE

If any accessories are missing or broken contact ATN’s Customer Ser-

vice.

INSTALLATION OF BATTERIES

The Thor-HD will operate on four AA-type Lithium batteries.

NOTE

We highly recommend using lithium AA

batteries. They will provide much longer bat-

tery life. Use only 1.5 V batteries.

Install batteries as follows:

1. Remove the battery cap by unscrewing it

counter clockwise.

2. Insert batteries as shown.

3. Return the battery cap into the housing

socket (screw clockwise until finger tight). Make

sure that the Red O-Ring is not visible to pre-

vent shut off issues due to recoil, but also Do not over-tighten! You want to

ensure you can unscrew the cap next time you replace batteries.

NOTE

Make sure that the device is turned off before changing source of

energy (batteries or USB in power supply mode).

MicroSD, USB

AND HDMI PORTS

The device is equipped with microSD, micro

USB and micro HDMI ports and can be found

under the cap near the battery block (marked

with appropriate icons on the cap).

NOTE

Make sure the device is turned off before

inserting the microSD card into the slot.

To Use:

1. USB cap cover should be unscrewed

counterclockwise.

2. Format new cards before use.

3. Insert microSD card as shown.

4. To lock, insert card in the slot and

push it with a thin object (a small coin,

paperclip, toothpick, etc.).

5. Return the cap to the USB cap cover

(screw clockwise until finger tight).

NOTE

There is only one correct direction to

insert the microSD Card. Do not force

the card into the slot, as it may damage

both the scope and the card itself.

To remove the microSD Card from the

slot:

1. Push it in using the same thin object.

2. When it pops up a few millimeters, it

can be pulled with your fingers or tweezers.

NOTE

If you are going to record video, the microSD card should be a Class 10 (10

Mb/s) or faster and have capacity from 4 to 64 Gb.

FIRMWARE UPDATE

Before operating your device, update the firmware to the latest version.

To receive a notification of new firmware updates, please register your

device on our website (you’ll receive an email letting you know when the new

firmware becomes available).

To update the new firmware you will need a microSD card and batteries that

are fully charged.

NOTE

In the event of a power failure during an update. The device may crash,

corrupting its system files. It will need to be sent back to the ATN factory for

service. DO NOT USE an additional source of power during firmware update!

Update the new firmware as follows:

1. Download the ***.bin file from

https://www.atncorp.com/firmware (You

may need to create an account, if you

didn’t create it earlier) and copy to your

microSD Card — root directory.

2. Insert the card into the device.

3. Turn ON the device.

4. In the “Firmware Update” dialog

box select “Yes” to start the update.

5. When the update counter reaches

“100%” the device will automatically restart.

6. Once the device is powered up it will enter self configuration mode.

7. After completing it will automatically restart and will be ready for use.

8. Motion Sensing platform will be configured when first turned on.

9. Once the Firmware update completes, please do a factory reset before using

the product.

10. Please remember to delete the Firmware File off of the microSD card after

all steps are completed.

NOTE

If the device does not restart within 30 seconds, remove and re-insert

the batteries, and again power-up the device. Once the device has been

updated you will need to either format the card or delete the update file

manually. In the event you do not perform the previous actions, the system

will ask you if you wish to update the device every time you turn it on.

ON/OFF

To TURN ON the device,

press and hold the POWER

Button until you see the ATN

splash screen.

To TURN OFF the device,

press and hold the POWER

Button until the “Shut down

the device?” appears in the

dialog box. Choose “Yes” to turn off the unit.

NOTE

Upon startup you must perform a NUC. Please refer to page 26 to learn

how to perform the NUC process correctly.

USING KEYPAD

The KEYPAD is programmed to be used

in two different ways:

• Short and Quick Taps — used for most

functions and to get around the menu;

• Press and Hold — designed to be

used in the following situations — ON/

OFF, ZOOM and SHORTCUT MENU.

NOTE

Using LEFT or RIGHT buttons in the

Menu will allow you to quickly choose

Exit Shortcut from any position.

FOCUSING

DIOPTER ADJUSTMENT

Look through the eyepiece, focusing on

the reticle on the screen, and rotate the

Diopter Adjustment Ring until optimal

sharpness is achieved. Do not take the

rubber cap off the objective lens.

NOTE

You should not have to re-adjust the

Diopter Adjustment unless another

user, with different vision needs, uses

the scope.

FOCUS ADJUSTMENT

Remove the cap from the objective lens

and rotate the focus adjustment ring, as

necessary, to achieve the proper focus at

various distances.

DIOPTER

ADJUSTMENT RING

FOCUS

ADJUSTMENT

RING

MOUNTING YOUR SCOPE

OPEN CLOSE

Secure the ThOR-HD to your Picatinny Rail using the Quick Release Mount

as shown above. However, the ThOR-HD 384 1.25-5x has a different mount —

with two fixing screws.

1. Slightly loosen the fixing

screws on the 7/8˝ weaver

mount built into the scope.

2. Place the scope on the

weaver rail of the firearm.

3. Tighten the fixing screws.

NOTE

Fixing screws may need

to be tightened after con-

tinuous shooting. ATN rec-

ommends using “Loctite”

to ensure screws do not

loosen up during shooting.

COMPASS CALIBRATION

When the compass needs

to be calibrated, the word

“CAL” appears instead of

the Compass Scale. To cal-

ibrate, rotate the three axis

points as pictured on the left,

on the device.

NOTE

After calibrating the de-

vice, please remember that

the compass will work best

when holding the ThOR-HD

parallel to the ground.

Other possible abbreviations:

• ERR — an error was detected, you may need to restart the device or reca-

librate the compass;

• SMF — your device is under a strong magnetic field, move away from the

source;

• UPD — your firmware needs to be updated.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mira telescópica de ATN

ATN

ATN Aries MK390 "Paladin" Manual de usuario

ATN

ATN Mars 2 Manual de usuario

ATN

ATN Aries MK300 Manual de usuario

ATN

ATN Mars4x-3 Manual de usuario

ATN

ATN nIGHT aRROW 4 Manual de usuario

ATN

ATN NVSG1 Manual de usuario

ATN

ATN LTAD-SN Manual de usuario

ATN

ATN Daytime Series Manual de usuario

ATN

ATN ATN MArs x4 Manual de usuario

ATN

ATN PS40-3P Manual de usuario

ATN

ATN Ultra Sight DC Manual de usuario

ATN

ATN ThOR Series Manual de usuario

ATN

ATN Digital Ultra Sight Manual de usuario

ATN

ATN tHor color Manual de usuario

ATN

ATN PS-40 Manual de usuario

ATN

ATN ATN 4X12 Manual de usuario

ATN

ATN Aries 390 Paladin Manual de usuario

ATN

ATN 3.5X26 Manual de usuario

ATN

ATN Daytime 5x33L Manual de usuario

ATN

ATN 10x65Z-Army Mil-Dot Manual de usuario

ATN

ATN Aries MK350 "Guardian" Manual de usuario

ATN

ATN ThOR 3 B&W Manual de usuario

ATN

ATN Mars4x-3P Manual de usuario

ATN

ATN Trident Pro2x-2 Manual de usuario

Manuales populares de Mira telescópica de otras marcas

Leupold

Leupold Hunting Equipment Guía del usuario

Newcon Optik

Newcon Optik DN482 Manual de usuario

Bushnell

Bushnell ET3124F Manual de usuario

Newcon Optik

Newcon Optik NVS-33 Manual de usuario

Nikon

Nikon 8442 - Omega Muzzleloader Scope 1.65-5x36 Manual de usuario

Pulsar

Pulsar Trail Series Manual de usuario

FLIR

FLIR ThermoSight T50 Manual de usuario

Pulsar

Pulsar Digisight Ultra N450 Manual de usuario

Nikon

Nikon 1.65-5x36 Manual de usuario

Nikon

Nikon OMEGA Muzzleloading 3-9x40 Manual de usuario

Zeiss

Zeiss Classic Diatal T Series Manual de usuario

Nikon

Nikon 4-16x50SF - Monarch Riflescope - BDC Manual de usuario

COT

COT NM-108 BC Manual de usuario

Nikon

Nikon 4-16x42SF - Monarch Riflescope Manual de usuario

Minox

Minox ZP5 3-15x50 Manual de usuario

Bushnell

Bushnell 20-4124 Manual de usuario

StreamLight

StreamLight STINGER 700025 Manual de usuario

Bushnell

Bushnell 71-3946 Manual de usuario