Atmel ATSAMB11 BluSDK SMART Manual de usuario
ATSAMB11 BluSDK SMART
Alert Notification Profile - Getting Started Guide
USER GUIDE
Introduction
The Alert Notification Profile allows a device like a watch to obtain information from a cellphone about
incoming calls, missed calls, and SMS/MMS messages. The information may include the caller ID for an
incoming call or the sender’s ID for email/SMS/MMS but not the message. This profile also enables the
client device to get information about the number of unread messages on the server device.
The iPhone®implements a custom variant of ANS called ANCS. A separate example application
implementing this custom variant is available in the BluSDK SMART package.
The example application explained in this document will only work with BLE compatible Android phones
running Atmel SmartConnect mobile application. Unlike iPhone, Android does not natively support Alert
Notification Service. The Atmel SmartConnect mobile application implements this service and can be
used to demonstrate this example application. The example application supports missed call alert and
SMS alert notification.
The device implements the GATT Client, which reads (or gets notified) about the characteristic values
from the GATT server (the mobile device). The Atmel®ATSAMB11 device must be paired with an Android
phone. After connection and discovery, missed call or SMS alert notifications can be enabled/disabled.
The Atmel SmartConnect application will notify missed calls or SMS alerts, which are then displayed on
the terminal console on the device side. The following chapters provide a detailed description of running
this demo.
The ‘SW0’ user button on the ATSAMB11 is programmed in such a way that each successive button
press will either enable or disable the notifications.
Features
Device Discovery and Disconnection
Pairing/Bonding
Alert Notification Service
Alert on incoming call
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
2
2
Table of Contents
1Purpose .....................................................................................................................3
2Demo Setup..................................................................................................................3
3Hardware Setup ...........................................................................................................3
4Software Setup.............................................................................................................4
4.1 Installation Steps...................................................................................................................................4
4.2 Build Procedure.....................................................................................................................................4
5Console Logging .........................................................................................................6
6Running the Demo.......................................................................................................6
7BluSDK SMART Software Architecture....................................................................10
8ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........11
9Revision History ........................................................................................................12
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
3
3
1 Purpose
This getting started guide describes the setup of an Atmel ATSAMB11 Xplained board and bringing up an
example profile supplied as part of BluSDK SMART release. The Alert Notification Profile is an example
application that is embedded as part of the software release package.
This document explains the details about:
1. Getting started with the setup of ATSAMB11 to be used as a Notification Consumer.
2. Getting the ANS Application working on the above mentioned setup.
The example application provided currently supports ‘Missed Call Alert and SMS Notification’.
2 Demo Setup
3 Hardware Setup
Connect the ATSAMB11 board to the host PC using a Micro-USB cable.
Figure 3-1. EDBG USB Port
BLE Link
Android phone
Atmel SmartConnect app
(Notification Provider)
ATSAMB11
(Notification Consumer)
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
4
4
4 Software Setup
4.1 Installation Steps
1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer
(recommended)]
http://www.atmel.com/tools/ATMELSTUDIO.aspx.
2. Install the latest Atmel Software Framework.
This package will install the following examples within the Atmel Studio environment:
Alert Notification application for ATSAMB11
4.2 Build Procedure
The following procedure is explained for ATSAMB11 application example.
1. Select New Example Project.
Figure 4-1. Creating a New Example Project
2. Select “SAMB11” in device family, enter “alert notification” in search window, and expand Atmel
Corp Projects. The location and the name of the project can be selected in the respective fields.
Click OK.
Figure 4-2. Selecting Alert Notification Application from Example Projects
3. Accept the license Agreement. The Atmel studio will generate the Alert Notification Profile project
for ATSAMB11.
4. Build the solution.
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
5
5
Figure 4-3. Building the ANP Application
5. Download the application via the USB to the ATSAMB11 board by using the Device Programing
option available in Tools as shown below.
Figure 4-4. Flashing the Application on Atmel MCU
6. Inside the device programming the user has to select the correct configuration for the device and
finally program the device by using the program button.
Figure 4-5. Flash Programming
7. Once the application is flashed, now ANP Application is ready for usage.
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
6
6
5 Console Logging
For the purpose of debugging, a logging interface had been implemented in the ANS Application.
The logging interface utilizes the same EDBG port that connects to ATSAMB11. A serial port monitor
application (for example TeraTerm) shall be opened and attached to the corresponding COM port
enumerated on the PC by the device. Baudrate should be set to 115200.
6 Running the Demo
1. Open a console window using TeraTerm or any equivalent serial port monitor application and
connect to the corresponding COM port enumerated on the PC. Configure the COM Port with the
following settings: Baudrate 115200, Parity None, one Stop bit, one Start bit, no Hardware
Handshake.
2. Press the Reset button on the ATSAMB11 board.
3. The device is now in advertising mode.
Figure 6-1. Display for Advertising Mode
Initializing Alert Notification Profile Application
Initializing SAMB11
BD Address:0xF8F005F23FFF, Address Type:0
Device is in Advertising Mode
4. On the Android phone, enable Bluetooth®in the Settings page. Start the Atmel SmartConnect
mobile application and allow it to scan for devices. ATMEL-ANS will appear amongst the devices
scanned. Click on ATMEL-ANS to connect to the ATSAMB11 device.
Figure 6-2. ATMEL-ANS Device Discovery on Atmel SmartConnect Application
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
7
7
5. Once connected, the client side will request for the pairing procedure with the Android phone. The
console log provides a guidance for the user to enter the pass-key on the phone.
Figure 6-3. Figure 9: Console Display for Pairing in ANP
Alert Notification Profile Application
Initializing SAMB11
BD Address:0xF8F005F23FFF, Address Type:0
Device is in Advertising Mode
Connected to peer device with address 0xccfa00710852
Connection Handle 0
Peer device request pairing
Sending pairing response
Please Enter the following Pass-code(on other Device):123456
Pairing procedure completed successfully
6. On Android phone side, a pop-up screen prompting the user to enter the pass-key will appear.
Enter ‘123456’ in the text box and click on ‘Pair’.
Figure 6-4. Pairing Pop on Android Phone
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
8
8
7. After pairing the Alert Notification service page is displayed as shown.
Figure 6-5. ANS Services Page
8. Enable the notifications by using the SW0 button. The mobile app should reflect the status as
shown.
Figure 6-6. Alert Notification Screen on Atmel SmartConnect Application
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
9
9
9. The user can trigger a missed call to the Android phone or send an SMS. The corresponding
notification then gets displayed on the ATSAMB11 side as shown below in the console logs.
Figure 6-7. Alert Notification Screen on Atmel SmartConnect Application
New Alert received
The no of new alerts are 1
The alert type is :
Missed Call alert
Unread alert received
The no of unread alerts are 0
New Alert received
The no of new alerts are 2
The alert type is :
Missed Call alert
Unread alert received
The no of unread alerts are 1
The alert type is :
Missed Call alert
ATSAMB11 BluSDK SMART –Alert Notification Profile –Getting Started Guide [USER GUIDE]
Atmel-42609A-ATSAMB11-BluSDK-SMART-Alert-Notification-Profile-Getting-Started-Guide_UserGuide_112015
1
0
10
7 BluSDK SMART Software Architecture
Figure 7-1 illustrates the top level diagram for the ATSAMB11 configuration.
Figure 7-1. ATSAMB11 Software Architecture
Otros manuales para ATSAMB11 BluSDK SMART
6
Tabla de contenidos
Otros manuales de Hardware de computadora de Atmel
Atmel
Atmel AVR2016 Manual de usuario
Atmel
Atmel AT91MEC01 Manual de usuario
Atmel
Atmel AT91SAM7L-STK Manual de usuario
Atmel
Atmel AVR ATmega324PA Manual de usuario
Atmel
Atmel ATWINC3400 Manual de usuario
Atmel
Atmel AVR1939 Instrucciones de instalación y funcionamiento
Atmel
Atmel ATmega8535L Manual de usuario
Atmel
Atmel RCB256RFR2 Instrucciones de uso
Atmel
Atmel ATAK2270 Manual de usuario
Atmel
Atmel AT88CK109STK3 Manual de instalación
Atmel
Atmel ATAN0008 Manual de usuario
Atmel
Atmel ARM Thumb AT91 Manual del instalador
Atmel
Atmel STK501 Manual de usuario
Atmel
Atmel AT24C16C Manual de usuario
Atmel
Atmel AVR ISP Manual de usuario
Atmel
Atmel ATF16V8B Manual de usuario
Atmel
Atmel FPSLIC AT94KAL Series Manual de usuario
Atmel
Atmel AVR STK500 Manual de usuario
Atmel
Atmel ATDH2200E Manual de usuario
Atmel
Atmel REB233-XPRO Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
