Atdec AWM 710 Arm Manual de usuario
AWM-A71T Page 1 of 4
Installation Guide
AWM-A71T
AWM 710 Arm
COMPONENT CHECKLIST
A
Monitor Arm
(x1)
B
VESA Head
(x1)
C
Channel Clamp
(x1)
D
Screw
M4x10mm
(x4)
E
Security
Screw
(x1)
F
4mm
Allen Key
(x1)
REQUIRED TOOLS
WEIGHT RANGE
• Phillips Head Screwdriver
Monitor weight should be within the
weight range of all modular elements
that make up the complete monitor
mounting solution.
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove or throw away the plastic sleeve on the channel clamp.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with Atdec AWM Series Posts and Wall Channels
! This product is not suitable for outdoor use or mobile applications
! Do not over-tighten screws and adjustment points on product.
! VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations, and unevenly weighted monitors
(relative to the center of the VESA mounting interface) exert additional leverage that can exceed the capacity of the mount even
though the monitor weight may be within the stated range. Please contact Atdec if you would like further information.
Flat Monitor
0 - 9kg
(0 - 20lb)
Curved Monitor
0 - 9kg
(0 - 20lb)
Curved monitors with an overall
depth up to 140mm (5.5”).
AWM-A71T Page 2 of 4
1. Fix channel clamp to post or wall channel
1.1 Ensure knob is undone. 1.2 Slide channel clamp into channel.
Push knob to
aid insertion
1.3 Hold clamp in desired position on
channel and turn knob to lock in place.
1. Ensure Knob is undone
3. Fit arm onto channel clamp
Note: Check the
arm rotation is
smooth after
tightening.
3.1 Push arm onto shaft. 3.2 Ensure arm is fully pushed onto shaft. 3.3 Tighten joint screw.
2. Ensure arm is fully pushed onto clamp
3. Tighten set screw
Tip: Check the
arm rotation is
smooth after
tightening.
IMPORTANT
Ensure plastic
sleeve is tted
on clamp
3. Place the rotation ring
in the desired postion
2. OPTIONAL Set arm rotation to 180°
2.1 Remove plastic sleeve
from channel clamp.
2.2 Remove rotation ring. 2.3 Place rotation ring in desired position and replace plastic sleeve
Note: rotation ring placement
depends on the position of the clamp
on the post. The tag on the ring
should always face toward the user.
1. Remove plastic sleeve
2. Remove rotation ring
1. Press
2. Lift
Note rotation is set to 360° by default.
180°
360°
OR
Default
Position
Flipped
Position
Tag
AWM-A71T Page 3 of 4
6. Monitor arm cable management
Important
Ensure enough
cable slack is
given to allow
for movement
of the monitor
1
1
2
6.1 Plug cables into the monitor
and route the cables down the arm
using the cable hooks and clips.
4. Attach VESA head to monitor
OK
Too long
Monitor
VESA Plate
VESA Screw
Too short
4.2 Attach VESA head
onto monitor with
provided screws.
(Alternatively, use
fasteners specied
by the monitor
manufacturer)
4.1 Check VESA mounting
compatibility of monitor
100mm
75mm
100mm
75mm
Note: For other sizes, use
a suitable adaptor plate
(sold separately).
Note: Recessed 75x75
VESA interfaces will
require a Spacer Kit
(sold separately)
Note: ensure screw length
suits the monitor VESA
mounting holes.
5. Attach monitor to arm
5.1 Fit monitor onto arm.
Note: VESA Head will
automatically latch
onto the tilt head.
Click
5.2 OPTIONAL SECURITY SCREW
If desired, once monitor is attached to the
arm, Install the security screw. This disables
the release switch, preventing theft.
AWM-A71T Page 4 of 4
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20231101
DO NOT OVERTIGHTEN
Increasing tension only stiffens
movement and cannot lock off
arm movement.
TIGHTEN LOOSEN
7. OPTIONAL Adjust tilt tension
Note: Support
monitor while
adjusting.
7.1 Factory set tilt tension will be
suitable for most monitors.
If required, adjust the tilt tension
using the 4mm hex key.
TIGHTEN
LOOSEN
8. OPTIONAL Adjust rotation tension
8.1 Tune the rotation tension
using 4mm hex key.
Adjustment may only be
required for ultrawide monitors.
HOLDS POSITIONDROOPS FORWARD
HOLDS POSITIONDRIFTS
9.1 Arm movement can be
adjusted to be rmer or more
free. Use the 4mm hex key to
adjust the tension of the three
pivot joints on the arm.
9. OPTIONAL Adjust arm joint tension
10. Removing monitor
10.1 Slide release switch up and
click into unlocked position, then
lift monitor away from the arm.
Click
Slide
Otros manuales de Rack y soporte de Atdec
Atdec
Atdec AWM-A71 Manual de usuario
Atdec
Atdec AWMS-2-BT75-FS Manual de usuario
Atdec
Atdec ADBS-2x2-17MFB Manual de usuario
Atdec
Atdec AWMS-DW Manual de usuario
Atdec
Atdec Telehook Manual de usuario
Atdec
Atdec AD-WM-7060 Manual de usuario
Atdec
Atdec AWM-A71-B Manual de usuario
Atdec
Atdec AWM-W6 Manual de usuario
Atdec
Atdec VFS-DV Manual de usuario
Atdec
Atdec AWMS-BT40 Manual de usuario
Atdec
Atdec AWM-FC Manual de usuario
Atdec
Atdec APA-B Manual de usuario
Atdec
Atdec VFS-DH Manual de usuario
Atdec
Atdec AWMS-2-D13-C Manual de usuario
Atdec
Atdec TH-1040-CTS Manual de usuario
Atdec
Atdec Visidec VF-AT-NP Manual de usuario
Atdec
Atdec ADBS-2x1-17TC Manual de usuario
Atdec
Atdec AD-TVAC-CM Manual de usuario
Atdec
Atdec TELEHOOK TH-3060-UT Manual de usuario
Atdec
Atdec AWM-W35 Manual de usuario
