Atdec AD-TVC-45 Manual de usuario
Atdec AD-TVC-45 Page 1 of 4
Installation Guide
AD-TVC-45
AV Cart 45
COMPONENT CHECKLIST
A
Base (x1)
I
Shelf
(x1)
J
LHS Vesa
Bracket (x1)
K
LHS Vesa
Bracket (x1)
A1
M8x25
Screw (x4)
B1
M6x25
Screw (x4)
C1
M5x25
Screw (x4)
D1
M4x12
Screw (x4)
E1
ø16xø6.2
Washer (x4)
F1
ø15x10mm
Spacer (x4)
A2
M8x26
Cap Screw
(x6)
B2
M8x55
Cap Screw
(x4)
C2
M5x15
Screw (x2)
D2
Display
Lock (x2)
E2
ø16.5xø12.5
Washer (x4)
F2
M6 Allen
Key (x1)
L
LHS Shelf
Support (x1)
M
RHS Shelf
Support (x1)
C
Mounting Plate (x1)
B
Column
(x1)
D
Mounting
Brace (x1)
E
Cover
(x1)
F
Shelf
Clamp (x2)
G
Castor
(x4)
H
Grommet
(x4)
N
Hook and
Loop (x3)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product should only be installed by professional installers of good mechanical aptitude, who fully understand these
instructions and the consequences of incorrect installation.
! Do not over tighten screws.
! Two person installation is recommended.
! Product not suitable for use outdoors.
! After installation is complete check to verify that TV Cart is secure and safe for use.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA
locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range.
Please contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control
or toys placed on the cart may encourage a child to climb on the cart and as a result the cart may tip over on to the child.
REQUIRED TOOLS
• Phillips Head Screwdriver
CAPACITY
DISPLAY
0-45kg (0-100lb)
32”-65”
SHELF
0-4.5kg (0-10lb)
Atdec AD-TVC-45 Page 2 of 4
1. Install the castors
E2
1.1 1.2
WARNING!
! CART CAN TIP OVER RESULTING IN RISK OF INJURY!
! DO NOT ALLOW CHILDREN UNDER 16 TO PLAY WITH OR MOVE CART
! MOVE CART SLOWLY
DO NOT PULLNEVER APPLY FORCE
AT TOP
APPLY FORCE ON
NARROW SIDES
PUSH NEAR MIDDLE
DO NOT APPLY
MOVING FORCE ON
FRONT OR BACK
ONLY ADULTS SHOULD
MOVE THIS CART
LOCK
BRAKES WHEN
STATIONARY
UNLOCK
BRAKES BEFORE
MOVING
DO NOT PULL
NEVER APPLY FORCE AT
TOP
APPLY FORCE ON
NARROW SIDES
PUSH NEAR MIDDLE
DO NOT APPLY MOVING
FORCE ON FRONT OR
BACK
ONLY ADULTS SHOULD
MOVE THIS CART
LOCK
BRAKES WHEN
STATIONARY
UNLOCK
BRAKES BEFORE
MOVING
2. Attach column to the base
F2
A2
E
A2
F2
2.1 2.2 2.4
2.3
Note: Make sure cable management
windows are facing the rear of base.
Caution: Ensure
screws are secured firmly.
3. Set column height
Right
upper
column
Right
lower
column
Left
upper
column
Left
lower
column
Spring
button Depress
Spring button
3.1 Use thumb or finger to depress
the spring button located in the cable
window on the lower right column.
At the same time use other hand to
twist then pull upper column upward
until your desired height. Twist
motion is to ensure spring button
doesn’t engage unintentionally.
Twist upper column back toward the
plunger holes and engage the spring
button into the plunger hole. Ensure
spring button pops out as shown in
Fig-2.
3.2 Repeat step 1 on left column.
Fig-1 Fig-2
Atdec AD-TVC-45 Page 3 of 4
5. Attach mounting plate
B2
D
C
F2
4. Assemble and install shelf
M
L
I
F
F
F
F
A2
F2
A2
F2
4.1
4.4
4.2 4.3
6. Attach VESA brackets to display
F1
K
E1 (A1, B1,C1)+E1+F1/D1+E1
J
Fastener configuration examples
M8x25mm A1 M4x12mm D1
M5x25mm C1
M6x25mm B1
Note: Use spacers
where necessary to
ensure brackets are not
loose, and screws are
not forced too deep
into the display.
Atdec AD-TVC-45 Page 4 of 4
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20211008
8. Cable routing options
N
H
Note: Grommets must be
inserted into tube prior
to inserting cables.
9. Adjust display height
9.1 Two people are required to change display height.
Display must be removed prior to adjusting height.
8.1 Cables may be routed down the
inside or outside of column.
9.2 Person “A” holds the top section of the
telescopic column. Person “B” depresses left
and right spring buttons on column by using
thumbs, so that person “A” can move top of
column down or up to desired height.
Take care to ensure spring buttons are not
pressed further than necessary to disengage
from column.
9.3 When height is determined, let spring
button set into plunger holes. Ensure both
spring buttons have popped out.
Spring button
7. Mount display
D2 C2
7.1 Hook display over mounting bracket
and centre display.
7.2 Attach both display locks to prevent
accidental dislodgement of display.
Maintenance
• Tighten fasteners and check the cart is secure and safe to use
at regular intervals (at least every three months.)
• Please contact your distributor if you have any questions.
Otros manuales de Rack y soporte de Atdec
Atdec
Atdec ADB-FS Manual de usuario
Atdec
Atdec TELEHOOK TH-3060-UT Manual de usuario
Atdec
Atdec TH-1026-VF Manual de usuario
Atdec
Atdec VFS-DV Manual de usuario
Atdec
Atdec Visidec Focus Micro Manual de usuario
Atdec
Atdec TH-1040-CTS Manual de usuario
Atdec
Atdec AWM-W6 Manual de usuario
Atdec
Atdec AD-TVAC-CM Manual de usuario
Atdec
Atdec ADBS-2x2-17MFB Manual de usuario
Atdec
Atdec AWM-BT Manual de usuario
Atdec
Atdec AWMS-2-LTH75-H Manual de usuario
Atdec
Atdec AWM-A46-B Manual de usuario
Atdec
Atdec AWMS-2-BT75-FS Manual de usuario
Atdec
Atdec Telehook Manual de usuario
Atdec
Atdec AD-WM-7060 Manual de usuario
Atdec
Atdec SPACEDEC ACROBAT Instrucciones de operación
Atdec
Atdec Freestanding Quad Manual de usuario
Atdec
Atdec AWM-W35 Manual de usuario
Atdec
Atdec Visidec VF-AT-NP Manual de usuario
Atdec
Atdec ADBS-3x1-30T3C Manual de usuario
