AT&T E250 Manual de usuario

User Manual (Part 2)

2.4 GHz Expansion

Handset E250

For use with AT&T models

E2555 • E2525 • E2600B

ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 1

Table of contents

AT&T and the Globe Design are trademarks of AT&T Corporation.,

licensed to Advanced American Telephones.

STOP! See pages 2-3

for easy instructions

You must charge

batteries and register the

handset before use

For customer service or product

information, visit our web site at

www.telephones.att.com

or call 1-800-222-3111

Please also read

Important Product Information

Enclosed in product package

Before you begin........................................1

Parts checklist.............................................1

Battery installation & charging................2

Registering the handset............................3

Belt clip & optional headset ....................4

Quick reference guide..............................5

ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 2

Before you begin

This cordless telephone operates with

the maximum power allowed by the

Federal Communications Commission

(FCC). Even so, this handset and base

can communicate over only a certain

distance — which can vary with the

locations of the base and handset, the

weather, and the construction of your

home or office. For best performance,

keep the base antenna fully upright.

If you receive a call while you are

out of range, the handset might not

ring — or if it does ring, the call might

not connect when you press PHONE.

Move closer to the base, then press

PHONE to answer the call.

If you move out of range during a

phone conversation, you might hear

noise or interference. To improve

reception, move closer to the base.

If you move out of range without

pressing OFF, your phone will be left

“off the hook.” To hang up properly,

walk back toward the telephone base,

periodically pressing OFF until the call

is disconnected.

Parts checklist

Remember to save your sales receipt and original packaging in case you ever need to

ship your telephone for warranty service. Check to make sure the telephone package

includes the following:

Handset charger

Telephone

handset

Power

adapter

Belt clip

Batteries

ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 1

LOW BATTERY

Battery installation & charging

Install batteries as shown, then place the handset in the charger for at least 8 hours

before use. You can keep batteries charged by returning the handset to the charger after

each use. When battery power is fully depleted, a full recharge takes about 6 hours.

Press coin into slot on

base of handset to

release latch, then

remove battery cover

Insert supplied

batteries

Place handset in charger to

charge for 8 hours before first use.

Light remains on while batteries

are charging.

Low battery indicator

Return handset to charger to recharge

when this symbol flashes. (Handset

will beep when battery is low.)

Caution: Use only AT&T 2AA

NiCad or NiMH rechargeable

batteries. Do not use AA

alkaline batteries.

Insert top

tab first

To replace battery cover

Press down to

click in place

REDIAL MEM

Plug power cord into jack on underside

of charger, then plug transformer into

electrical outlet

ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 2

Registering the handset

Before using your new handset, you must register it with

the base. During registration, you must enter the 15-digit

ID number of the telephone base. To find this number, go

to the base, press MENU, scroll down to select DISPLAY

BASE ID, then press OK.

The handset provided with your telephone is automatically

registered as Handset 1. Additional handsets will be

assigned numbers in the order they are registered (2, 3, 4,

etc.) up to a maximum of eight.

ENTER BASE ID

123456789012345

Enter base ID, then press OK

HANDSET 2

Handset 1 Handset 2 Handset 3

REDIAL MEMMENU

ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 3

Belt clip & optional headset

Install belt clip as shown below if desired.

For hands-free telephone conversations, you can use any industry standard 2.5 mm

headset (purchased separately). For best results use an AT&T 2.5 mm headset.

Snap belt clip into notches on

side of handset. Rotate and pull

to remove.

Plug 2.5 mm headset

into jack on side of

handset (beneath

small rubber cap)

ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 4

HANDSET 1

REDIAL MEM

Off/Clear

During a call, press to hang up.

While using menus, press to cancel an

operation, back up to the previous

menu, or exit the menu display.

Quick reference guide

Speaker

Press to activate handset speaker-

phone. Press again to switch call back

to earpiece.

Softkeys

Press a softkey to select a menu item

displayed just above the key.

Phone/Flash

Press to begin a call, then dial a number.

During a call, press to receive an incoming

call, if Call Waiting is activated.

Sound Select

Press to customize speaker sound for

clear speakerphone conversations.

Xfer/Intercom

Press to transfer a call or initiate an

intercom conversation.

Redial Log Phonebook

Screen menus

Item 1 Item 2 Item 3

Menus

Main Menu

Calls Log

Play Messages

Handset Settings

Set Time

Clock Mode

Handset Settings

Ringer Volume

Ringer Melody

Low Batt Tone

Range Tone

Keypad Tone

Contrast

Language

For complete instructions, please refer to the manual provided with your telephone.

ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 5

AT&T and the Globe Design are trademarks of AT&T Corporation,

licensed to Advanced American Telephones. Printed in China. Issue 1.1 AT&T 12/30/03.

www.telephones.att.com

ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Auricular de AT&T

Manuales populares de Auricular de otras marcas

Swissvoice

Swissvoice ePure HD Manual de usuario

Philips

Philips TD6736/BH051P Manual de usuario

ASCOM

ASCOM I62 - Manual de usuario

LG-Ericsson

LG-Ericsson LIP-9010 Manual de usuario

GE 1583 Manual de usuario

iiNet

iiNet Handset Manual de usuario

ASCOM

ASCOM 9p23 Manual de usuario

AirCell

AirCell ST 3100 Manual de usuario

Eaton

Eaton HHIR-LCD-PROG Instrucciones de montaje

Mitel

Mitel 112 Manual de usuario

SBC

SBC SBC-381H Manual de usuario

Mitel

Mitel 5602 Manual de usuario

ASCOM

ASCOM d81 Messenger Instrucciones de instalación

SpectraLink

SpectraLink 7522 Manual de usuario

Avaya

Avaya L100 Series Cómo utilizar

ooma

ooma HD2 Handset Manual de usuario

Yealink

Yealink IPW56 Manual de usuario

Sony

Sony SBH52 Manual de usuario