AT&T AT3101 Manual de usuario

User’s manual

AT3101

Expansion DECT 6.0

cordless handset

For use with the AT&T AT3111-2

telephone system with

caller ID/call waiting

Congratulations

on purchasing your

new AT&T product.

Before using this AT&T product, please

read the Important safety instructions

on pages 18-21 of this manual.

Please thoroughly read the user’s

manual for all the feature operations

and troubleshooting information necessary to

install and operate your new AT&T product.

For complete instructions, please refer to

the manual provided with your AT3111-2

telephone

Model #: AT3101

Type:

Expansion DECT 6.0 digital cordless handset

Serial #:

Purchase date:

Place of purchase:

AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,

licensed to Advanced American Telephones. Printed in China.

The ENERGY STAR®program (www.energystar.gov)

recognizes and encourages the use of products that

save energy and help protect our environment. We

are proud to mark this product with the ENERGY

STAR®label indicating it meets the latest energy

efficiency guidelines.

See page 3

for easy instructions.

You must install and

charge the battery before

using the telephone. STOP!

CAUTION: To reduce the risk of fire or injury to persons or damage

to the telephone, read and follow these instructions carefully:

• Use only the supplied rechargeable battery or replacement battery (model:

BT8001) or equivalent.

• Do not dispose of the battery in a fire. Like other batteries of this

type, it could explode if burned. Check with local codes for special

disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is corrosive

and may cause damage to the eyes or skin. It may be toxic if

swallowed.

• Exercise care in handling batteries in order not to create a short

circuit. Do not allow conductive materials such as rings, bracelets, or

keys to touch the battery. The battery or conductor may overheat and

cause harm.

• Charge the battery provided with or identified for use with this

product only in accordance with the instructions and limitations

specified in this manual.

• Observe proper polarity orientation between the battery and battery

charger.

• Do not disassemble your telephone. There are no user-serviceable

parts inside. Refer to qualified service personnel for servicing.

Parts checklist

Your new AT&T AT3101 expansion handset includes:

Cordless telephone

handset

Handset battery Belt clip

Battery

compartment

cover

User's manual Power adapter for

handset charger

Table of contents

Charger for cordless handset

User’s manual

AT3101

Expansion DECT 6.0

cordless handset

For use with the AT&T AT3111-2

telephone system with

caller ID/call waiting

Getting started

Parts checklist .......................1

Charger installation..............2

Battery installation and .

charging...............................3

Adding your new

handset................................4

Replacing a handset............5

Handset layout .......................6

Belt clip & headset...............7

Appendix

Troubleshooting .....................8

Important safety

instructions .....................18

FCC Part 68 and ACTA ....22

FCC Part 15...........................25

Limited warranty.................27

Technical specifications ..31

Getting started

1. Plug the small end

of the smaller power

adapter into the jack

on the underside of the

charger, then route the

cord through the slot as

shown.

2. Plug the

large end of

the smaller

power adapter

into an

electrical outlet.

Charger installation

NOTES:

1. Use only the power adapter supplied with this product or equivalent.

2. This power unit is intended to be correctly oriented in a vertical or floor mount

position. The prongs are not designed to hold the plug in place if it is plugged

into a ceiling or an under-the-table/cabinet outlet.

Install the charger as shown below. Make sure that the electrical

outlet is not controlled by a wall switch.

Getting started

Battery installation & charging

The battery may have enough charge for short calls. For optimal

performance,

we recommend that you charge the handset for

16 hours. You can keep the battery charged by returning the

handset to the telephone base after each use. When the battery

power is fully depleted, a full recharge takes about 16 hours.

When fully charged, the handset battery provides approximately

eight hours of talk time and four days of standby time.

HB9wwwwW,wwwwwwww

EBBHC9WWwww,wwww,ww

HB9wwwwW,wwwwwwww

EBBHC9WWwww,wwww,ww

HB9wwwwW,wwwwwwww

EBBHC9WWwww,wwww,ww

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery (model BT8001).

2. See the Troubleshooting section on pages 8-17 for charging issues.

1. Align the two holes

of the battery plug

with the socket

pins in the handset

battery compartment,

matching the red and

black wires to the

color-coded label.

2. Place the

battery in the

compartment

with the wires in

the lower right

corner.

3. Position

the battery

compartment

cover and slide

it towards

the unit until

it clicks into

place.

4. Charge the handset by placing the

handset face up in the telephone base

or in the charger. The CHARGE light will

be on when charging.

Getting started

Adding your new handset

NOT REGISTERED

PRESS FIND HNDST

4 SEC ON BASE

PLEASE WAIT...

HS X

REGISTERED

Handsets purchased separately need

to be registered to the telephone base

before use. When first purchased, all

optional accessory handsets will show

NOT REGISTERED on the screen. The new

handset may need to be charged for five

minutes before registering to the main

telephone base.

To register a handset to your telephone

base

1. Place the unregistered handset into the

telephone base. If

PRESS HNDST LOC 4

SEC ON BASE

does not appear on the

handset screen after a few seconds,

remove the handset and place it in the

telephone base again.

2. On the telephone base, press and hold FIND

HANDSET for about four seconds (until

the red IN USE light on the telephone

base turns on) and then release the

button. The handset will show

PLEASE

WAIT...

and it will take about 10 seconds

to complete the registration. The handset

will show

HS X REGISTERED

and will beep

if registration is successful.

NOTES:

1. If the registration is not successful, the display

will show NOT REGISTERED. To reset the

handset, remove the handset from the telephone

base and place it back in. Try the registration

process again.

2. You cannot register a handset if any telephone

connected to the same telephone line is in use.

Getting started

When you are replacing rather than adding a handset, for

your handsets to be numbered sequentially, you need to

delete all the handset registrations on the telephone base.

To de-register all handsets

1. Press and hold FIND HANDSET on the telephone base

for about 10 seconds (until the IN USE light turns on

and starts to flash), then release the FIND HANDSET

button.

2. Immediately press and release FIND HANDSET again.

You must press FIND HANDSET while the IN USE

light is still flashing. The IN USE light will flash for

approximately seven seconds.

3. Soon the handsets will show CONNECTING... and it will

take about 10 seconds to complete the de-registration

process. All handsets will show NOT REGISTERED if

deregistration is successful.

After deleting all handset registrations, you will need to

individually register each handset with the telephone base

(see page 4 for registration instructions).

NOTES:

1. If the de-registration process is not successful, you may need to reset

the system and try again. To reset: pick up the handset and press

the /FLASH button, then press the OFF/CLEAR button and place

the handset back into the telephone base. You may also reset by

unplugging the power from the telephone base then plugging

it back in.

2. You cannot de-register the handset(s) if any telephone connected to

the telephone line is in use.

Replacing a handset

NOT REGISTERED

Getting started

Handset layout

1. Earpiece

2. MENU/SELECT

SKIP

3. Headset jack (2.5mm)

4. CID (caller ID)

PLAY

5. /FLASH

6. Dialing keys (0-9, *,#)

7. VOICEMAIL

8. REDIAL/PAUSE

9. Microphone

10.Handset display

11.VOL / (volume)

12. (directory)

ERASE

13. (speakerphone)

14.OFF/CLEAR

15.#

16.INT (intercom)

17.MUTE/REMOVE

HANDSET 1

Getting started

Belt clip & optional headset

For hands-free telephone conversations, use any industry

standard 2.5mm headset (purchased separately). For best results,

use a AT&T 2.5mm headset.

Install belt clip as shown below if desired:

Plug the 2.5 mm headset

into the jack on the side

of the handset (beneath

the small rubber flap).

HANDSET 1

NOTE: If the sound

quality of the headset

is not satisfactory,

try unplugging it, and

firmly plugging it in

again.

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

Installation

Snap belt clip

into notches

on both sides

of handset.

Removal

Pull and unlock

one flap from the

notch first before

detaching the

whole belt clip from

handset.

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

IC:xxxxX-xxxxxxxx

FCC ID: XXxxx-xxxx-xx

Tabla de contenidos

Otros manuales de Auricular de AT&T

Manuales populares de Auricular de otras marcas

Swissvoice

Swissvoice ePure HD Manual de usuario

Philips

Philips TD6736/BH051P Manual de usuario

ASCOM

ASCOM I62 - Manual de usuario

LG-Ericsson

LG-Ericsson LIP-9010 Manual de usuario

GE 1583 Manual de usuario

iiNet

iiNet Handset Manual de usuario

ASCOM

ASCOM 9p23 Manual de usuario

AirCell

AirCell ST 3100 Manual de usuario

Eaton

Eaton HHIR-LCD-PROG Instrucciones de montaje

Mitel

Mitel 112 Manual de usuario

SBC

SBC SBC-381H Manual de usuario

Mitel

Mitel 5602 Manual de usuario

ASCOM

ASCOM d81 Messenger Instrucciones de instalación

SpectraLink

SpectraLink 7522 Manual de usuario

Avaya

Avaya L100 Series Cómo utilizar

ooma

ooma HD2 Handset Manual de usuario

Yealink

Yealink IPW56 Manual de usuario

Sony

Sony SBH52 Manual de usuario