Astone MT620-R Instrucciones de instalación
INSTALLATION AND OWNER'S MANUAL
Please carefully read these instructions before you begin to install the products.
Whirlpool Bathtub Model Number: MT620-R
07/11 Rev A
P/N:100056-06
Thank you for purchasing your Aston whirlpool bathtub. We hope that it will
provide you with years of satisfying use and enjoyment.
Please read this manual carefully because it contains information and instructions
about the proper installation of the unit. If you do not follow certain conditions of
installation and maintenance, your warranty may be affected.
Aston whirlpool bathtubs feature:
Air switch pump control
Massaging whirlpool jets
Easy maintenance durable fiberglass reinforced acrylic
Air control knob
Before you start
1
1.Whirlpool Jets
2.Air switch
3.Air control knob
4.Overflow
5.Drain
6.Suction cover
7.Pillow
WARNING: To reduce the risk of drowning, electrical shock, or injury, read the
following important precautions before using the unit. If you do not fully
understand the meaning of any of the precautions and warnings please consult
your dealer or the manufacturer for a full explanation. Do not use the unit until
you understand all of the following:
1. WARNING: Read and follow all instructions.
2. DANGER: To reduce the risk of injury, do not permit children to use the unit
unless they are closely supervised.
3. WARNING: Use this unit only for the intended purpose described in this
manual; do not use attachments not recommended by the manufacturer.
4. WARNING: Never drop or insert any objects into any opening.
5. WARNING: The unit must be connected to a supply circuit that is protected
by a ground fault circuit interrupter (GFCI). This GFCI should be provided by
the installer and routinely tested.
To test the GFCI:
a. Push the “test” button. The GFCI should interrupt the power going to
the unit.
b. Press the “reset” button and power should be restored.
If the GFCI fails to operate as described, the GFCI is defective and must be
replaced. If the GFCI interrupts power to the unit without the test button being
pushed, a ground fault has occurred. Discontinue use and contact your
dealer or service provider.
6. WARNING: If you have a pre-existing health condition such as obesity, heart
disease, high or low blood pressure, circulatory problems, or diabetes,
consult your physician before use. If you are pregnant or could be pregnant,
do not use the unit without consulting your doctor.
7. WARNING: Observe reasonable time limits when using this product. Long
exposures at high temperatures can cause high body temperatures.
Symptoms may include dizziness, nausea, fainting, drowsiness, and reduced
awareness. These effects could possibly lead to drowning.
8. WARNING: The water jets produce a stream of water with relatively high
pressure. Prolonged exposure of high-pressure water to a localized area of
the body may cause bruising.
9. WARNING: Prolonged immersion in hot water or steam may induce
hyperthermia. A description of the cause, symptoms and effects of
hyperthermia are as follows:
a. Lack of awareness of impending hazard;
b. Failure to perceive heat;
c. Failure to recognize the need to exit the unit;
d. Fetal damage in pregnant women;
e. Unconsciousness and danger of drowning.
Important Safety Instruction
2
10. WARNING: To avoid the risk of accidental injury or drowning children should
not use the hydro massage bathtub without adult supervision.
11. WARNING: To avoid injury, take care when entering or exiting the
hydro-massage bathtub.
12. WARNING: To avoid unconsciousness and possible drowning, do not take
drugs or drink alcohol before or during the use of a hydro massage bathtub
equipped with a heater.
13. WARNING: To prevent risk of fetal injury, a pregnant or possibly pregnant
woman should consult a doctor before using a hydro massage bathtub
equipped with a heater.
14. WARNING: To reduce the risk of hyperthermia and possible drowning, do
not use a hydro massage bathtub equipped with a heater immediately
following strenuous exercise.
15. WARNING: To reduce the risk of electric shock, do not permit electric
appliances (such as a hair dryer, lamp, telephone, radio, or television) within
1.5m (5 ft.) of a hydro massage bathtub.
16. CAUTION: Test the ground fault circuit interrupter (GFCI) protecting this
appliance periodically in accordance with the manufacturer's instructions.
17. WARNING: Water temperature in excess of 40 C (104 F) may be injurious to
your health and increase the risk of hyperthermia and drowning.
18. WARNING: To reduce the risk of hyperthermia, people using medication and
or having an adverse medical history should consult a doctor before using a
hydro massage bathtub equipped with a heater.
3
Please read and follow the installation instructions and guidelines in this section.
Failure to follow the recommended instructions and installation techniques may
lead to possible damage to the unit or the surrounding area and can affect
warranty claims.
ATTENTION: This unit requires assembly. A minimum of two people are
required for assembly, as several of the sections can be large and unstable until
assembled.
You will need the following tools:
Drill with screwdriver attachments
Caulk gun
Level (3 foot or longer is recommended)
Tape measure
Installation Guide
4
Phillips head screw driver
Bathroom rated silicone sealant
Electrical Requirements
Installation by a Licensed Electrician
15 Amp service, 110-120 VAC @ 60Hz
GFCI breaker required
Before starting the installation, please ensure that you have inspected all
components of the unit and check for broken or damaged sections. If you find
damage, please contact your dealer or the manufacturer.
5
Using a Phillips screw driver to remove the screws holding the skirt onto the
whirlpool tub
To remove the skirt but pulling down on the skirt carefully
Remove the whirlpool tub skirt
for access
6
The whirlpool bath is constructed with several leveling feet. Each foot has a
locking nut. Use an adjustable wrench and level to complete this next step.
1. Loosen all of the locking nuts so that the leveling feet are free and easy to
move.
2. Place the whirlpool bath into the exact final installation location or a flat
surface.
3. Place the level across the top of the whirlpool bath (side to side) and level the
whirlpool bath by adjusting the leveling feet.
NOTE: You may need to remove the whirlpool bath in order to adjust the leveling
feet, but always recheck the level with the unit in the final installation location.
4. Place the level across the top of the base (front to back) and level the base
by adjusting the leveling feet.
Level the whirlpool bath
for proper drainage
7
WARNING: Failure to apply proper pitch or grade for drainage can cause leaking
and/or flooding of the area surrounding the unit.
5. After making all the leveling adjustments ensure that all leveling feet
(including center foot) are in contact with the floor. To ensure the unit is
supported, stand in the whirlpool bath in several places looking for any
movement and adjust as needed.
6. After ensuring all leveling feet are in contact with the floor, tighten the locking
nut on each leveling foot ensuring that all leveling feet are secure.
7. Once all the leveling feet are secure, place the whirlpool bath back into the
final installation location and verify all the leveling adjustments remain as
before. Adjust as needed.
8
The Whirlpool tub comes equipped with a factory installed drain and overflow an
optional flexible drain hose is also provided to avoid having to move the floor
drain.
Please see the Drain diagram for the optional drain hose.
Use the following instructions for the standard straight drain:
1. Move the floor drain so that the floor drain and whirlpool tub drain are in line
when the whirlpool tub is in it's final position
2. With the whirlpool tub in it's final location make the plumbing connections
between the whirlpool tub and the floor drain.
Use these instructions for installation of the optional floor drain:
1. Apply sealant to the drain hose gasket and into the compression nut.
2. Install the hose, compression nut, and gasket assembly onto the lower drain
body.
3. Tighten the compression nut so that the gasket is compressed creating a
positive seal.
Optional drain connections
9
Flex drain hose
Tabla de contenidos
Manuales populares de Bañera de otras marcas
Lyons
Lyons Elite ETLxx663219 Series Manual de usuario
Woodbridge
Woodbridge BJ500 Instrucciones de montaje
Whirlpool
Whirlpool Ariel ARL-702 Manual de usuario
TEIKO
TEIKO EXCELLENT DUO Manual de usuario
American Standard
American Standard Colony 5-1/2' x 32" Manual de usuario
American Standard
American Standard 3052OD.X0X Guía de inicio rápido
