Assa Abloy D12-B2 Manual de usuario

ASSA ABLOY, the global

leader in door opening

solutions.

Installation instructions

ASSA Entré d12-K1

Accessory kit ASSA Entrance d12-B1,

d12-B2, d12-B3, d12-S1

”

All parts

Cylinder ring Knob protection

Knob square pin Stop washers Handle Handle square pin

Handle screw O-ring Barrel nut Drill

Lock case Pillar asym striking plate Screw to lock

case and security

striking plate

Screw for inclined installation

of security striking plate

Cylinder Cylinder extender High strength screw

Cylinder plug Cylinder sleeve

Check that your package

contains all parts using the

color codes.

Entrance d12-K1

Entrance d12-B1, B2, B3

Entrance d12-S1

Installation

To turn the lock from right to left and vice

versa, loosen the three screws (A) and

pull out the cases (B) and turn. Then press

the cases in and tighten the screws. If you

make this change the lock shield (C) must

also be turned 180°.

Doors manufactured before 1980 usually

have an asymmetrical opening; switch to

accompanying lock pillar.

Add a ø 24 mm extra hole to the opening

inside the door, see drilling template in

the box. Insert and screw in the lock case.

For accessory kit ASSA Entrance d12-S1, skip diagrams 2, 9, and 10.

If you do not have openings in the door for the lock case or striking plate, use the extra

installation instructions in the package.

Remove the cylinder sleeve on the inside

cylinder by pushing in the locking pin.

Note that the cylinder sleeve on the

outside cylinder must be fitted during

assembly.

Doors where the B and/or C dimension

exceeds 27 mm must be supplemented

with a 10 mm cylinder extender, at 37

mm with two cylinder extenders, etc.

Attach the cylinders from the inside

with the enclosed four screws.

3Check that arrows in the lock case point

downwards on both sides.

Point

downwards

7Block the screws with cylinder plugs. Turn the

key first to “ten o’clock” and push a plug into

the opening between the screws on the right

side of the cylinder. Then turn the key to the

“two o’clock” to mount the plug on the left

side. This is done to prevent removal of the

lock by someone who is unauthorized.

Slide on and snap in place the inside

cylinder sleeve.

Place the square peg for the knob in the

appropriate place and fasten it between

the lock case and handle plate with plastic

stop washers. Make sure the stop washers

do not jam in the hole. For extremely

thin or thick doors it may be necessary

to saw the square peg or replace it with a

longer one.

Put handle plate in place with the thumb

turn knob positioned vertically.

Slide the o-rings on the handle screws.

Install the door handle with the through-

handle screws from the inside of the door.

Install the barrel nuts from the outside. If

necessary, tighten the screws so that the

door handle hangs loosely and does not

rub against the door.

If the door is in poor condition or if

the insurance company has specific

requirements for approved lock units,

you can supplement with door

reinforcement accessory ASSA 4292 *

(green) and cover plate 4291* and

knob plate 4294*.

* Not included in the package.

11 Slide the cylinder rings on the outside

and the inside and secure with the screw

on the bottom of the cylinder ring.

A restricted “do not duplicate” key means that as owner and holder of the blue

code token, you are the only one who can have extra keys made. The purpose of

restricted keys is to give you control over your keys.

The front door lock must be safe, secure and convenient, and with the restric-

ted key, we have made the lock even better.

The blue code token should be considered and treated as a valuable

document.

Registration of ownership certificate

You can register the ownership certificate for your ASSA d12 cylinder and

key online at ASSA’s website www.assa.se. You can use the ownership cer-

tificate to have extra keys and cylinders made at a licensed ASSA service station

even if you lose the blue code token.

To register your ownership certificate you will need the 7-digit code from the

blue code token and a 3-digit security code that is enclosed in the package.

The keys to the d12 high-security cylinder are legally protected against illegal

copying under Swedish law. Contact a licensed ASSA service station if you need

additional keys or cylinders. You can find your nearest licensed ASSA service

station at www.assa.se.

• If you want your key to fit all doors in the

house (storage room, garage, etc.), you can

order extra cylinders and use the same key for

all locks. Use the code token in the same way

as when you order keys.

• If you are sure you do not need any additional

keys or cylinders, you can cut up and destroy

the blue code token. You will then be certain

that no new keys can be made.

• Test the key in the cylinder before installing

the lock.

Restricted “do not duplicate” key

Tips and advice

Care

Clean cylinders once or twice a year using ASSA cleaner and lube with ASSA

lock spray for optimum performance and long life. Never use oil, grease or

graphite.

ASSA ABLOY, the global

leader in door opening

solutions, dedicated

to satisfying end-user

needs for security, safety

and convenience.

ASSA AB

P.O. Box 371

SE-631 05 Eskilstuna

Sweden

phone +46 (0)16 17 70 00

fax +46 (0)16 17 70 49

Customer support:

phone intl. +46 16 17 71 00

phone nat. 0771 640 640

fax +46 (0)16 17 73 72

e-mail: helpdesk@assa.se

www.assa.se

M3124.1509

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerrar de Assa Abloy

Assa Abloy

Assa Abloy Yale Smart Latch Manual de usuario

Assa Abloy

Assa Abloy OneSystem 819N Guía de instalación

Assa Abloy

Assa Abloy Yale SIMPLICITY Manual de usuario

Assa Abloy

Assa Abloy Securitron SAM Manual de usuario

Assa Abloy

Assa Abloy IKON VERSO CLIQ V551 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy LOCWOOD 001TOUCH Manual de usuario

Assa Abloy

Assa Abloy Sargent PE80 Series Manual de usuario

Assa Abloy

Assa Abloy Yale YDM7220 Manual de usuario

Assa Abloy

Assa Abloy ELECTRIC LOCK Manual de usuario

Assa Abloy

Assa Abloy IKON eCLIQ N110 Manual de usuario

Assa Abloy

Assa Abloy Yale P113 Manual de usuario

Assa Abloy

Assa Abloy ALARM CONTROLS Magnalock 1200DE Delayed... Manual

Assa Abloy

Assa Abloy Sargent Profile v.S1 Manual de usuario

Assa Abloy

Assa Abloy MUL-T-LOCK SC110 Manual de usuario

Assa Abloy

Assa Abloy IKON eCLIQ N111 BA3 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin IN100 Series Manual de usuario

Assa Abloy

Assa Abloy EMTEK EMTouch Classic Style Instrucciones de funcionamiento

Assa Abloy

Assa Abloy OneSystem Espagnolette Manual de usuario

Assa Abloy

Assa Abloy SECURITRON 32 Series Manual de usuario

Assa Abloy

Assa Abloy Sargent XC Series Manual de usuario

Assa Abloy

Assa Abloy K100-622 Manual de usuario

Assa Abloy

Assa Abloy YRD256 Manual de usuario

Assa Abloy

Assa Abloy Yale Real Living Real Living YRC246 Especificaciones técnicas

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario

Assa Abloy d12-B2 Manual de usuario

Manuales populares de Cerrar de otras marcas