Assa Abloy 3090 Manual de usuario

Adams Rite Manufacturing Co.

260 Santa Fe Street

Pomona, CA 91767

Phone: 800-872-3267

Fax: 800-232-7329

www.adamsrite.com

eForce® 150 Keyless Entry

Adams Rite Manufacturing Co.

260 Santa Fe Street

Pomona, CA 91767

Phone: 800-872-3267

www.adamsrite.com

Installation

Instructions

Model 3090

February 2012 2 80-0180-351 Rev. E

80-0180-351 Rev. E 15 February 2012

Adams Rite Manufacturing Co. (hereinafter ADAMS RITE) manufactures its

products in a manner to be free of defects. Should any defect of manufacture

(in material or workmanship) occur in its products, ADAMS RITE, upon

prompt notification and proof to its satisfaction that the product was defective

in manufacture for the use intended by ADAMS RITE, will at its option, ex-

change the product, repair the defect or refund the price charged by ADAMS

RITE, FOB factory based on the following schedule:

All mechanical products for five (5) years from the date of manufacture;

All electrical products (including EL and ED exit devices) for three (3)

years from the date of manufacture;

The RITE Door®for five (5) years from the date of manufacture;

UltraLine Electric Strikes for five (5) years from the date of manufacture.

Limitations and exclusions: This is a limited warranty and is in lieu of all

other warranties including the implied warranties of merchantability and

fitness for use) and under no circumstances shall ADAMS RITE be liable for

any incidental or consequential damages or losses.

This warranty covers products as outlined above manufactured from May 1,

2003 forward.

This warranty does not cover damages from such causes as abuse, accident,

neglect, fire or freight damage.

WARRANTY CONDITIONS

The selling dealer from who this exit device was purchased is responsible for

advising the purchaser of the period of no charge warranty exchange, repair

or refund. Replacement parts under the terms of the warranty must be fur-

nished by the Adams Rite dealer or agency.

FACTORY ASSISTANCE

If the purchaser is unable to locate a service agency, or if the purchaser does

not receive satisfaction from the source of which the exit device was pur-

chased, or from local dealer, write or contact Adams Rite at the following ad-

dress:

Adams Rite Manufacturing Co.

260 Santa Fe Street

Pomona, CA 91767

Phone: 800-872-3267

Fax: 800-232-7329

February 2012 14 80-0180-351 Rev. E

80-0180-351 Rev. E 3 February 2012

Table of Contents

Installation Tools & Equipment .......................................................... 5

Door Preparation ............................................................................... 6

Spindle Preparation ........................................................................... 7

Lock Series Configuration.................................................................. 8

Handing the eForce®....................................................................... 10

Mortise Cylinder Installation............................................................. 11

Mounting the eForce®...................................................................... 12

Battery Installation ........................................................................... 13

Limited Warranty.............................................................................. 15

February 2012 4 80-0180-351 Rev. E

80-0180-351 Rev. E 13 February 2012

Battery installation eForce®150

Properly insert 4 (AA) Alkaline bat-

teries into battery holder observing

the polarity markings.

Plug battery pack into eForce®150

connector (FIG. 19).

Lithium batteries are suggested in

climates reaching 20°F and below.

Insert battery case into the eForce®

150 as shown (FIG 20).

Slide battery cover over the batter-

ies.

A battery moisture shield is pre-

installed at the factory to protect the

batteries from the elements.

Insert 5/64” Allen key (included)

and turn clockwise two full turns to

secure the battery cover.

(FIG. 21).

FIG. 19

FIG. 20

FIG. 21

February 2012 12 80-0180-351 Rev. E

Mounting the eForce®150

Insert the properly dimensioned spin-

dle into the output hub.

Mount eForce®150 onto mounting

bracket and guide spindle into Cam

Plug (MS 1850 configuration shown)

(FIG. 17a & 17b).

The eForce®150 must sit flush on

the door surface.

Secure with two (2) #10-32 x 5/8”

screws as shown in (FIG. 18).

FIG. 17a

FIG. 18

Spindle

FIG. 17b

80-0180-351 Rev. E 5 February 2012

INSTALLATION TOOLS & EQUIPMENT

IMPORTANT NOTES:

The 3090-01 is designed exclusively for latching hardware including:

Adams Rite 4500/4900 Deadlatches;

Adams Rite 8000 Series Exit Devices;

Yale 7200 Series Narrow Stile Exit Devices;

Corbin Russwin ED4000 Series, and

SARGENT 8500 Narrow Design Rim Exit Devices.

The 3090-02 is compatible with Adams Rite MS®Series Deadbolts only!

THESE UNITS ARE NOT INTERCHANGEABLE!

These instructions, and the fasteners supplied, apply to metal door

applications.

Other door types will need fasteners designed for the given medium.

TOOLS NEEDED:

Common hand tools such as center punch, drill gun, ¼”

drill bit, Phillips screwdriver, pliers, flat tip screwdriver,

pencil.

ADDITIONAL EQUIPMENT NEEDED:

Mortise Cylinder - 1” to 1½” in length range with MS cam

(Fig. 1). (Note: 1½” cylinders require a 1/8” trim ring).

SUPPLIED PARTS:

NOTE: A cam plug is

supplied for either the

3090-01 latch or 3090-02

lock.

THIS PRODUCT MUST BE

INSTALLED ACCORDING

TO ALL APPLICABLE

BUILDING AND LIFE

SAFETY CODES

Item Description Qty.

1Mounting Bracket (Part # 22-9076) 1

2#10-32 X 5/8” Phillips Pan Head Screws w/Lockwasher 4

3Spindle (Part # 22-9154) 1

45/64” Allen Key 1

5Cylinder Locking Ring (Part # 24-0061) 1

6Locking Ring Spanner Tool (Part # 22-0594) 1

FIG. 1

February 2012 6 80-0180-351 Rev. E

STEP 1 DOOR PREPARATION

FIG.2

Select the stick-on template to match the applica-

tion.

For Yale, Corbin Russwin and SARGENT exit

devices, use template 80-0180-396-01.

Mark the backset and horizontal centerlines.

Apply clear template over the centerline marks

(FIG. 2)

Center-punch four (4) referenced mounting holes

and remove template.

Drill holes at center-punch locations using a ¼” drill

bit.

Install Rivnuts. Refer to instructions supplied in

Rivnut kit.

Install mounting bracket (Item 1) with two (2) each of

#10-32 x 5/8” (Item 2) pan head screws. (FIG. 3)

FIG. 3

80-0180-351 Rev. E 11 February 2012

STEP 5 MORTISE CYLINDER INSTALLATION

Using a Philips Head Screwdriver, re-

move the eight (8) #10-32 x 5/8” screws

on the back of the eForce®150 and

gently lift the back plate off the housing.

CAUTION!There are wires connecting

the housing and back plate assembly.

Handle with care.

Do not over-tighten!

Install Cylinder into housing. Secure

and fasten with supplied locking ring

using locking ring spanner tool.

(FIG. 14)

Gently place back plate back on hous-

ing and secure with eight (8) #10-32 x

5/8” screws.

CAUTION!There are wires connecting

the housing and back plate assembly.

Handle with care.

Do not over-tighten!

Do not use Dummy Cylinder!

Remote Switch Kit RSK-3090 (Optional)

For applications that require a remote

activation switch, plug the RSK-3090

into the board as shown in Fig. 15 & 16.

FIG. 13

FIG. 14

FIG. 16

FIG. 15

February 2012 10 80-0180-351 Rev. E

STEP 4 HANDING THE eForce®150

The eForce®150 is shipped in a non-

handed neutral position with the access

cover off as shown.

To hand the eForce® 150, rotate the

handle until it clicks into the horizontal

position.

Proceed to step 5 if installing the

3090-02!

The output hub, located on the back of the eForce® 150,

is shipped with a clockwise rotation as viewed from rear.

In some instances, this rotation must be changed to

match the device and/or hand of the door (refer to

Handing Setup Chart).

To change rotation, insert a flat screwdriver into the output hub (FIG. 12)

located on the back of the eForce®150 and turn approximately 270° Clock-

wise or Counter-Clockwise.

This will reconfigure the unit to the opposite rotation.

HANDING SETUP CHART

DEVICE TYPE

LEFT HAND REVERSE

ROTATION

RIGHT HAND REVERSE

ROTATION

SVR CLOCKWISE CLOCKWISE

Mortise Latch COUNTER-CLOCKWISE CLOCKWISE

CVR CLOCKWISE CLOCKWISE

Rim COUNTER-CLOCKWISE COUNTER-CLOCKWISE

FIG. 12

NOTE:

Hubs that have (+) shape are for use with deadlatches & exits only.

Hubs that have (-) shape are for use with deadbolts only.

80-0180-351 Rev. E 7 February 2012

STEP 2 SPINDLE PREPARATION (For 1-3/4” doors)

For Adams Rite MS1850 Deadbolts, 4500/4900 Deadlatches, & 8000

Series Mortise Exit Devices:

Snap-off spindle at fifth (5th) notch as shown in FIG. 4. For 2” thick door add

one notch.

For Adams Rite 8600 Concealed Vertical Rod Exit Devices:

Snap-off spindle at sixth (6th) notch as shown in FIG.5. For 2” thick doors add

two notches.

For Adams Rite 8000 Series Surface Vertical Rod & Rim Exit Devices,

Yale 7200 Series Narrow Stile Exit Devices, Corbin Russwin ED4000

Series, and SARGENT 8500 Narrow Design Rim Exit Devices:

Snap-off spindle at fourteenth (14th) notch as shown in FIG. 6. For 2” thick

doors add two notches.

FIG. 6

Insert “T”

end into

exit devices

Fourteenth notch

FIG. 5

Sixth notch

Insert Flat

end into

exit devices

FIG. 4

Fifth notch

Insert Flat

end into

exit devices

February 2012 8 80-0180-351 Rev. E

STEP 3 CONFIGURE FOR LOCK SERIES

Mortise Latch Application: 3090-01 for 4500/4900

(including 8300/8400 Exit Devices)

Configure the supplied cam plug to match the hand of door. Insert camplug

into latch case with notch on the cam plug aligned with latch case set screw.

Tighten set screw and secure with the two brass cam plug screws.

CVR Exit Device Application: 3090-01 for 8500/8600

Install Tailpiece adapter on the vertical rod and fasten with Phillips screw as

shown.

FIG.9

Left Hand Reverse

(LHR)

FIG. 7

Right Hand Reverse

(RHR)

FIG. 8

80-0180-351 Rev. E 9 February 2012

RIM Exit Device Application: 3090-01 for 8700/8800

On the back side of the exit device, remove only

the lower Phillips head screw, depending on hand

of door, to free up the cylinder actuator for use.

(FIG. 10)

FIG. 10

MS 1850 Application –3090-02 for MS® Series Deadbolt

Two (2) brass hex head screws and the set screw

from the MS1850 will fasten the cam plug to the

MS1850. (FIG. 11)

For MS®Deadbolt, insert Cam Plug into lock case

with notch on the cam plug aligned with lock case

set screw.

Tighten set screw and secure with the two (2) brass

cam plug screws. Cam Plug must be positioned

below door surface.

FIG. 11

CYLINDER ACTUATOR SCREW

Otros manuales para 3090

Otros manuales de Cerrar de Assa Abloy

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Manual de usuario

Assa Abloy

Assa Abloy LOCKWOOD Sliding Door Latch Manual de usuario

Assa Abloy

Assa Abloy Securitron Shear Aligning Magnalock SAM... Manual de usuario

Assa Abloy

Assa Abloy IKON eCLIQ N111 BA3 Manual de usuario

Assa Abloy

Assa Abloy Yale inTouch Especificaciones técnicas

Assa Abloy

Assa Abloy SECURITRON CEPT-10 Manual de usuario

Assa Abloy

Assa Abloy ABLOY EL574 Manual de usuario

Assa Abloy

Assa Abloy Lockwood Optimum Manual de usuario

Assa Abloy

Assa Abloy Yale Smart Latch Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy Effeff 843G Manual de usuario

Assa Abloy

Assa Abloy HES KS100 Aperio Instrucciones de montaje

Assa Abloy

Assa Abloy Securitron Vista V2M1200 Series Manual de usuario

Assa Abloy

Assa Abloy Door Lock Manual de usuario

Assa Abloy

Assa Abloy OneSystem 819N Guía de instalación

Assa Abloy

Assa Abloy Yale 5300LN Series Guía de inicio rápido

Assa Abloy

Assa Abloy Lockwood 3579 Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin HPSK Manual de usuario

Assa Abloy

Assa Abloy 8800 Series Manual de usuario

Assa Abloy

Assa Abloy Securitron M680EBD Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manual de usuario

Assa Abloy

Assa Abloy 1048.10 Guía

Assa Abloy

Assa Abloy Corbin Russwin IN100 Manual de usuario

Assa Abloy

Assa Abloy Sargent Passport 1000 PG Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario