Assa Abloy Sargent AD-PE8600 Manual de usuario
1-800-727-5477 • www.sargentlock.com
Installation Instructions
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written
permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in damage
to the product and void the factory
warranty.
WARNING
PE8600 Series (12-MD, MD, & AD)
Concealed Vertical Rod Exit Devices
A8305-1 5/23
2
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
A8305-1 5/23
Screw Chart
SCREW
TOTAL QTY
SUPPLIED
WHERE USED
#10-24 X 3/4" FLAT HEAD
MACHINE SCREW
4
(4) CHASSIS
CORNER MOUNTING HOLES
#10-24 X 3/4" ROUND HEAD
MACHINE SCREW
2
(2) REAR MOUNTING PLATE
#10-24 X 3/8" FILLISTER HEAD
MACHINE SCREW
1
(1) INNER CHASSIS
TOP MOUNTING HOLE
#10-24 X 3/8" OVAL HEAD
MACHINE SCREW
4
(2) TOP CASE
(2) BOTTOM PLATE (IF AD)
1/4"-20 X 1/2" FLAT HEAD
MACHINE SCREW
2(2) BOTTOM PLATE
(MD OR FIRE RATED)
#10-24 X 1/2" U'CUT FLAT HEAD
MACHINE SCREW
5
(1) INNER CHASSIS
BOTTOM MOUNTING HOLE
(2) 640 OR 650 STRIKE, TOP
(METAL FRAME)
(2) 640 OR 650 STRIKE, BOTTOM
(METAL FRAME)
#10 X 1-1/4 FLAT HEAD
WOOD SCREW
2
(2) 650 STRIKE, TOP
(WOOD FRAME)
(2) 650 STRIKE, BOTTOM
(WOOD FRAME)
1/4"-20 X 2" FLAT HEAD
MACHINE SCREW W/ANCHOR
2
(2) 606 BOTTOM STRIKE
(FIRE RATED)
#8-32 X 5/16" W/ #6 OVAL HEAD
MACHINE SCREW
6
(4) CHASSIS COVER
(2) END CAP
1/4"-20 X 2-3/8" KNURLED FLAT HEAD
2
(2) EXIT TRIM
(IF USED)
AA
EE
FF
DD
GG
HH
3
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
A8305-1 5/23
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Rail Cutting Guide (Provided)
Support Block (Provided)
Equipment Needed
Tools
Before installation:
1. Fit and hang door.
2. Check the box’s label for the size of the exit device.
The surface of the door where the exit device is to be applied must be flush. Clear away
any raised projections to allow exit device to rest on the flat surface of the door. If shim
kit is required, contact your distributor.
Note: Please refer to trim and other installation instructions provided in the box.
Strike Pack for AD-PE8400
640 TOP AND BOTTOM STRIKE
#10 X 1/2"
PHILLIPS FLAT HEAD
MACHINE SCREW
(4 I N P A C K F O R T O P
AND BOTTOM S TRIKE)
Strike Pack for MD-PE8400 Strike Pack for 12-MD-PE8400
Strike Packs
MD-PE8600
AD-PE8600 12-MD-PE8600
4
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
A8305-1 5/23
Template AD-PE8600, NB-AD-PE8600 & NB-MD-PE8600, MD-PE8600, 12-MD-PE8600
Omit holes for NB- AD version and all MD- versions.
.395
.300
.150
10-24 UNC - 2B
ONLY FOR RHRB
THRESHOLD IF USED
MUST LEAVE A MINIMUM
.350
ONLY FOR LHRB
ONLY FOR RHRB
.187
.187
.811 2.388
AND DOUBLE DOORS)
CENTER LINE OF RAIL
ONLY FOR RHRB
FOR LHRB, SEE DETAIL A
NOTES:
DOOR PREPARATION SHOWN FOR INSIDE DOOR ONLY.
1.
IF OUTSIDE PULL AND/OR OUTSIDE CONTROL IS USED, SEE APPROPRIATE DOOR TEMPLATE FOR OUTSIDE DOOR PREP.
2.
3.
4.
WE RECOMENDED THAT ALL TAPPED HOLES BE DRILLED AND TAPPED IN FIELD.
5.
TOLERANCE ALL FRACTIONAL DIMENSIONS
6.
7.
8.
9.
OPENING FOR
INSERTING DEVICE
C
L
OF RODS
MINIMUM CLEAR
OPENING FOR
INSERTING DEVICE
TOP OF DOOR
.811
.350
2.388
DETAIL A
SCALE 1 : 1
FEATURE FOR LHRB
For MD-bottom plate prep.
May be omitted for NB-MD
versions.
1/2
"
5/8
"
1/4-20 Tapped Holes (2 Places)
2-3/4
"
3/8
"
5
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
A8305-1 5/23
*Note: The NB-AD-PE8600, NB-MD-PE8600 & the 12-NB-MD-PE8600 do not have a bottom rod assembly.
Exploded View
End cap
INSIDE
LEFT HAND
REVERSE
BEVEL
RIGHT HAND
REVERSE
BEVEL
THIS EXIT DEVICE IS HANDED
CHECK HAND OF DEVICE AGAINST APPLICATION
OUTSIDE
Push rail assembly
Center case chassis
Chassis cover
16- Cylinder Lockdown
(Exploded View For Clarity)
Slide mounting rail insert
with cylinder dogging
(16-prefix) into mounting
rail.
Top Chassis
Top Bolt
Chassis
*Bottom rod assembly
Mounting Plate
Rod silencer
6
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
A8305-1 5/23
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Remove door from frame, and prepare the door per template.
1
7
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
A8305-1 5/23
2
Screw top bolt and rod assembly and bottom bolt
and rod assembly into the inner chassis.
*Bottom bolt rod and assembly will not be used with
NB devices.
Top bolt and rod assembly
*Bottom bolt and rod assembly
8
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
A8305-1 5/23
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
3
Feed rod and inner chassis assembly into the door. Ensure teeth face down and top bolt teeth are opposite
the inside door prep.
Top bolt teeth
9
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
A8305-1 5/23
FLAT HEAD SCREW
#10-24 x 1/2”
FILLISTER HEAD SCREW
#10-24 x 3/8”
4
5
Locate chassis on the fillister head screw (FF). Attach to the door with (4) #10-24 x 3/4 flat head screws (AA).
Do not fully tighten screws.
AA
FF
Attach inner case chassis to the door with (1) #10-24 x 1/2” flat head screw (HH) and secure with (1) #10-24
x 3/8” fillister head machine screw (FF). If P700 series trim is being used, it must be installed at this point. See
P700 instructions for details.
HH
10
1-800-727-5477 • www.sargentlock.com
Copyright © 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
A8305-1 5/23
PE8600 Series (12-MD, MD, & AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
6
Adjusting the top bolt and rod assembly
• 1/8” gap or less between door top and frame: Rotate bolt to make it even with the top of the door.
• 1/8” gap or greater: Bolt must extend above the door, equal to the gap, minus 1/8”.
Adjusting the bottom bolt and rod assembly (Not needed for NB exit devices)
• 1/8” gap or less between door bottom and high point: Rotate bolt to make it even with the top of the
door.
• 1/8” gap or greater: Bolt must extend below the door, equal to the gap, minus 1/8”.
Note: Rod must be retracted while adjusting bolt projection. Depress chassis lift arm to retract top bolt
and rod assembly.
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Cerradura de puerta de Assa Abloy
Assa Abloy
Assa Abloy Connect 50 Manual de usuario
Assa Abloy
Assa Abloy Emtek F20 Manual de usuario
Assa Abloy
Assa Abloy Sargent PR100 Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin CLX3300 Manual de usuario
Assa Abloy
Assa Abloy Lockwood Standalone Manual
Assa Abloy
Assa Abloy 1489 Manual de usuario
Assa Abloy
Assa Abloy HES KS100 Aperio Manual
Assa Abloy
Assa Abloy Yale Doorman Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin Access 600 TCRNE1 Series Manual de usuario
Assa Abloy
Assa Abloy SARGENT Profile Series Manual de usuario
Assa Abloy
Assa Abloy effeff MAG-600SM Manual de usuario
Assa Abloy
Assa Abloy effeff Mini Magnet Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin Access 800 Series Manual de usuario
Assa Abloy
Assa Abloy Sargent 6-Line Manual de usuario
Assa Abloy
Assa Abloy SARGENT 5300 Series Manual de usuario
Assa Abloy
Assa Abloy 1264 Manual de usuario
Assa Abloy
Assa Abloy v.G1 Sargent Manual de usuario
Assa Abloy
Assa Abloy Corbin Russwin ED5200N Series Manual de usuario
Assa Abloy
Assa Abloy HES 8000 Series Manual de usuario
Assa Abloy
Assa Abloy R10 Manual de usuario
