Artesyn MVME2500 Series Manual de usuario

MVME2500

Quick Start Guide

P/N:6806800L03B (February 2014) Observe ESD-safe

measures

What’s in the box?

Install the RTM

When installing or servicing the

module or accessories, strictly

observe the safety precautions

in the Safety Notes. Otherwise,

personal injury or property dam-

age may occur.

• Use either a properly grounded ESD

wrist strap or make sure that you are

working in an ESD-safe environ-

ment.

• Connect to the ESD connector at the

front or the rear of the system.

Make sure you receive all items of

your shipment:

• MVME2500 VMEbus board

• Other items that were ordered

• Printed Safety Notes Prepare the installation

site

• For information on the environmen-

tal and power requirements, see the

MVME2500 Installation and Use man-

ual.

• Operating temperatures refer to the

temperature of the air circulating

around the blade and not to the

actual component temperature.

1. Power down all equipment and discon-

nect the power cable from the AC

power source.

2. Remove the chassis cover.

3. Remove the filter panel(s) from the card

slot(s) at the rear of the chassis (if the

chassis has a rear card cage.

4. Install the top and bottom edge of the

transition module into the rear guides

of the chassis.

5. Ensure that the levers of the two injec-

tor/ejectors are in the outward posi-

tion.

6. Slide the transition module into the

chassis until resistance is felt.

7. Move the injector/ejector levers in an

inward direction.

8. Verify that the transition module is

properly seated and secure it to the

chassis using the two screws adjacent

to the injector/ejector levers.

9. Connect the cables to the transition

module.

MVME2500-Quick Start Guide

Artesyn Embedded Technologies, 2900 South Diablo Way, Suite 190, Tempe AZ 85282-3222, USA

Finding more information

For more information on the product, see

the MVME2500 Installation and Use and

other related documentation.

Visit our Web site

https://www.artesyn.com/computing. Use

the SUPPORT>TECHNICAL DOCUMENTA-

TION link to look for Technical Documenta-

tion.

Technical Assistance

To request technical assistance, visit our

Web site https://www.artesyn.com/com-

puting/support/

Install the board6

1. Attach an ESD strap to your wrist. Attach

the other end of the strap to an electrical

ground. Make sure that it is securely fas-

tened throughout the procedure

2. Remove VME filler panels from the VME

enclosures, as appropriate.

3. Install the top and bottom edge of the

board into the guides of the chassis.

4. Ensure that the levers of the two injector/

ejectors are in the outward position.

5. Slide the board into the chassis until

there is resistance.

6. Simultaneously move the injector/ejec-

tor levers in an inward direction.

7. Verify that the board is properly seated

and secure it to the chassis using the two

screws located adjacent to the injector/

ejector levers.

8. Connect the appropriate cables to the

board.

9. To remove the board from the chassis,

reverse the procedure and press the red

locking tabs (IEEE handles only) to

extract the board.

Install the PMX/XMC

Support

1. Remove the PMC/XMC filler plate from

the front panel cut-out.

2. Slide the front bezel of the PMC/XMC into

the cut-out from behind. The front bezel

of the PMC/XMC module will be flushed

with the board when the connectors on

the module align with the mating con-

nectors on the board.

3. Align the mating connectors properly

and apply minimal pressure to the PMC/

XMC until it is seated to the board.

4. Insert the four PMC/XMC mounting

screws through the mounting holes on

the bottom side of the board, and then

thread the four mount points on the

PMC/XMC. Tighten the screws.

5. Install the board into the appropriate

card slot. Make sure that the board is well

seated into the backplane connectors.

Do not damage or bend connector pins.

6. Replace the chassis or system cover.

7. Reconnect the system to the power

source and then turn on the system.

The MVME2500 does not support hot swap.

Power off the slot or the system and make

sure that the serial ports and switches are

properly configured.

Otros manuales para MVME2500 Series

Otros manuales de Computadora de placa única de Artesyn

Artesyn

Artesyn iVPX7225 RTM Guía de inicio rápido

Artesyn

Artesyn MVME2502 Guía de inicio rápido

Artesyn

Artesyn MVME51005E Guía de inicio rápido

Artesyn

Artesyn ATCA-7370 Guía de inicio rápido

Artesyn

Artesyn ATCA-7360 Guía de inicio rápido

Artesyn

Artesyn iVPX7225 RTM Manual de usuario

Artesyn

Artesyn ATCA-7475 Guía de inicio rápido

Artesyn

Artesyn MVME2500-ECC Manual de usuario

Manuales populares de Computadora de placa única de otras marcas

WIN Enterprises

WIN Enterprises PL-80910 Manual de usuario

AXIOMTEK

AXIOMTEK SBC81206 Series Manual de usuario

Embest

Embest SOM-PH8800 Manual de usuario

SeaLevel

SeaLevel SBC-R9 Manual de usuario

SMART Embedded Computing

SMART Embedded Computing ATCA-8310 Manual de usuario

WinSystems

WinSystems PPM-LX800-G Manual de usuario

GIGAIPC

GIGAIPC QBiX-PPC Series Manual de usuario

OLIMEX

OLIMEX A10S-OLinuXino-MICRO Manual de usuario

Commell

Commell FS-978 Manual de usuario

GIGAIPC

GIGAIPC QBiP-8665A/ Manual de usuario

VersaLogic

VersaLogic Python EBX-11 Manual de usuario

Micro Computer Specialists

Micro Computer Specialists IRV-3702 Manual de usuario

CompuLab

CompuLab SB-A510 Manual de usuario

Boser

Boser HS-7321 Manual de usuario

Premier Farnell

Premier Farnell Embest SBC8530 Manual de usuario

MicroSys Electronics

MicroSys Electronics miriac SBC-LS1043A2 Manual de usuario

Aaeon

Aaeon UP Manual de usuario

Portwell

Portwell WUX Series Manual de usuario