Arkon RCBTABLED Manual de usuario
Telescoping pole extends
upward from 17 inches to
29 inches.
Compatibility:
Fits smartphones with
cases weighing up to 2
pounds and measuring
up to 4” wide.
IMPORTANT:
Do not overtighten ring.
Overtightening may
damage threads on
holder and also make it
difficult to adjust phone
and tablet holders.
3 4
2
Insert pole into base.
PLEASE NOTE—this will be a tight fit and will require some force.
Your Remarkable Creators Bundle will arrive in eight pieces:
Telescoping Pole
25mm to 1/4”-20
Camera Bolt Adapter
(optional)
Weighted Base
with Allen Wrench
1
RV001WR-B
Attach overhead arm assembly by unscrewing the collar at the top of
the pole until the metal ball side of the overhead arm assembly fits
into the collar. Tighten collar clockwise to secure.
Unscrew tightening ring from holder.
Place ring over the 17mm end of mount
then snap the holder onto the ball. Set to
desired position, then tighten ring.
Using two hands, insert phone into the
holder by pushing the device into one of the
spring-loaded support arms. Expand the other
support arm and fully insert device until it lays
flat against the blue rubber pad.
SP25MMCAM
Assembled Mount
SP3RMPR0
SPHD8BASE
SPHD8L29
Tighten clockwise
to secure.
Tightening Ring
Telescoping
Pole
Allen
Wrench
Tightening
Knob
Collar
Metal
Ball side
Continued on page 2
RCBTABLED | Remarkable Creators Video Phone Stand Bundle rev.053118
SPHD8L29
SPHD8BASE
Phone Holder
LED Ring Light
RV001WR-B
Overhead Arm
Assembly
SP3RMPR0
Clamp Post Mount
GN031-SBH-B
SPLEDRING
TAB001
GN031-SBH-B
5Shafts can be adjusted by unscrewing
the shafts’ knobs to loosen. Tighten
knobs to set.
Tablet Holder
TAB001
7
9
10
6
8
To attach optional camera/pico projector adapter, unscrew shaft knob and
remove phone holder, ring, and ball adapter. Attach the 25mm ball end of the
camera adapter to the shaft and tighten clockwise to secure.
Unscrew mount’s knob to loosen grip. Place mount around pole and
tighten knob to secure. Push down on lower legs of spring-loaded holder to insert tablet.
Ring light clips onto phone.
For instructions on how to assemble tablet holder, refer to included
TAB001 manual. Attach tablet holder by inserting the mount’s Dual
T-Tabs into the holder’s Dual T-Slots.
Adjust the height of the pole by loosening the adjustment collar
counterclockwise. Tighten clockwise to set height.
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9 am -5pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan and USA
© Copyright 2018 Arkon Resources, Inc.
Safety Precautions
Always use two hands (one on shaft, and one on base) when carrying.
Failure to properly secure the stand’s shaft to the base could cause
bodily injury or harm. The Arkon Pro Stand is designed for use with
smartphones and small cameras. If using heavier devices, be sure to add
a counterbalance in order to prevent the stand from falling over. Arkon
Resources, Inc. is not responsible for any damages caused to your device
or yourself due to the installation or use of this mount.
!
page 2
Tightening
Knob
RCBTABLED | Remarkable Creators Video Phone Stand Bundle rev.053118
OPTIONAL
Otros manuales de Rack y soporte de Arkon
Arkon
Arkon MP070-7PS-1 Manual de usuario
Arkon
Arkon SM236 Manual de usuario
Arkon
Arkon BBP135 Manual de usuario
Arkon
Arkon CM983 Manual de usuario
Arkon
Arkon IPM127 Manual de usuario
Arkon
Arkon CM395 Manual de usuario
Arkon
Arkon BBP125-S Manual de usuario
Arkon
Arkon TT125 Manual de usuario
Arkon
Arkon PTM129-SRVC Manual de usuario
Arkon
Arkon BB212 Manual de usuario
Arkon
Arkon CM934 Manual de usuario
Arkon
Arkon SM511 Manual de usuario
Arkon
Arkon CM160 Manual de usuario
Arkon
Arkon BB228 Manual de usuario
Arkon
Arkon SM229-SRVC Manual de usuario
Arkon
Arkon CM925-S Manual de usuario
Arkon
Arkon CLAMPRV29 Manual de usuario
Arkon
Arkon TTGO129-ST-RVC Manual de usuario
Arkon
Arkon BBP132 Manual de usuario
Arkon
Arkon VG917-KST Manual de usuario
