Arecont Vision H.264 Day/Night SurroundVideo Series Manual de usuario

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

1 | Page

H.264 Day/Night SurroundVideo

Installation Manual

Inside the box:

A. Arecont Vision SurroundVideo

camera

B. Mounting template

C. RJ45 female to female coupler

D. Hex key

E. Security L-key

F. Pack of four (4) wood screws and four (4)

dry wall anchors

Not included but needed:

#1 Phillips head screwdriver

#2 Phillips head screwdriver

Flat head screwdriver ( for side conduit

opening)

Image 1

Mounting the Camera:

1. Remove camera and hardware from the box.

2. Using the mounting template, prepare the

mounting provisions for camera installation.

NOTE: Since SurroundVideo

series ship with

both surface mount and in-ceiling mount, the

mounting template takes both into

consideration.

3. Using security L-key, loosen the four (4)

screws securing the dome cover (Image 2).

Remove vandal resistant dome cover.

NOTE: Do not remove screws from the dome

cover.

Image 2

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

2 | Page

4. If using in-ceiling mount, please use #2

Phillips head screwdriver to loosen the four

(4) machine screws (Image 3) and remove in-

ceiling mount housing from surface mount

housing. (Image 4)

NOTE 1: The above removed screws are also

used to attach the camera with in-ceiling

mount housing to the pendant mount (Image

5) and wall mount (Image 6). Do not

disregard.

NOTE 2: The in-ceiling mount only can be

attached on hard ceilings including wood,

plastic, metal and concrete.

NOTE 3: For use in a false ceiling, a flush

mount adapter kit must be used.

Image 3

Image 4

Image 5

Image 6

In-Ceiling Mount

Surface Mount

Screws

Pendant Mount

Wall Mount

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

3 | Page

5. If you are using the side conduit opening on

the surface mount, remove the conduit plug

by first removing the socket set screw using

the provided Allen key (Image 7) and remove

the conduit plug using a flat screwdriver.

Note: the conduit fits ¾” NPT standard

Image 7

Connecting External Power: (Optional)

6. If the camera is powered by an outside power

supply, 12~20VDC or 24VAC, connect the

power cable shown in Image 8.

Red

Black

–

Table 1

NOTE: Make sure that your installation of

wires complies with Electrical Code of the

local government where the camera is

installed and no bare wires are exposed.

Image 8

External camera

Power input

RJ45 Connector

Digital I/O connector

Heater & Blower

Power input

Heater & Blower

Power input

Conduit Plug

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

4 | Page

Connecting Digital I/O: (Optional)

7. To use digital I/O, connect the I/O cable

shown in image 8.

Electrical Characteristics:

Min

Max

Input voltage (V)

2.9

6.3

(measured between + and –terminals)

OFF

1.3

Output current (mA)

(measured between + and –terminals)

Applied Voltage Rage: 0 - 80V

OFF

0.1

Table 2

NOTE: Both the input and the output are

electrically isolated from the rest of the

camera’s electrical circuitry via general-

purpose photo couplers. The input is

additionally protected with a serial 250 Ohm

resistor, and a debouncing circuit. Duration of

any input signal should be at least 5 ms to

comply with the requirements of the

debouncing circuit.

Orange

OUT +

Yellow

OUT –

White

IN +

Black

IN -

Table 3

Off

Heater

17C° (62.6 °F)

30 °C (86 °F)

Blower

10C° (50°F)

15 °C (59 °F)

Blower

50C° (122 °F)

45 °C (113°F)

Table 6

Connecting Heater and Blower : (AV8185DN-HB

and AV8365DN-HB only)

8. To run the heater and blower shown in Image

8, connect heater & blower power input to

12V to 20V DC or 24VAC power supply.

(Image 9).

Power input

Power consumption

DC12V to 20V

11 Watts

AV24V

13 Watts

Table 4

Red

Black

–

Table 5

Image 9

Dual power board

Heater board

Blower

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

5 | Page

9. Align the holes in the camera with the

prepared holes on the mounting surface.

Attach the camera with in-ceiling mount

housing to the surface mounting housing

shown in Image 4.

10. To insert camera with in-ceiling mount into

hard ceiling with the wood screws or any

optional hardware suitable for the mounting

surface shown in Image 10

.Image 10

Note: Use Flush Mount Adapter for false

ceiling tile installation. (Image 11) Please

refer to Flush Mount Adapter Installation

Instructions on page10.

Image 11

Adjusting Tilt, Pan and Focus:

10. Power on camera to adjust tilt, pan and focus.

11. To adjust the pan, use a #2 Phillips

screwdriver to loosen both screws on the

sides of the plastic gimbal bracket as shown

in Image 12 and Image 13.

12. Adjust the pan as required and tighten the

screw from step 11 shown in image 14.

Image 12 Image 13

Image 14

Set Screws

360

Wood Screws

Flush Mount

Adapter

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

6 | Page

13. To adjust the tilt, use a #2 Phillips screwdriver

to loosen both screws on the sides of the

plastic gimbal bracket 1/4 turn (Image 15 and

16). CAUTION: Do not remove the screws!

14. Adjust lens tilt as required and tighten the

screws from step 13 shown in image 17.

NOTE: the camera has 2-Axis gimbal with

360° pan and 100° tilt for easy and accurate

positioning.

Image 15

Image 16

Image 17

15. To adjust focus, loosen set screw on each

lens as shown in Image 18.

16. Adjust lens focus as required and tighten the

screws from step 15.

Image 18

Set Screws

100

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

7 | Page

Adjusting Each Sensor Tilt : ( AV8365DN only)

NOTE: Each sensor tilt angle can be adjusted

by +/- 10° to remove the dead spot at dome

bottom or at the horizon.

15. To adjust each sensor tilt angle, use a #1

Philips screwdriver to turn set screws, shown

in Image 19 and Image 20.

16. Remove the protective film from the camera

dome.

NOTE: be careful not to scratch the vandal

dome cover.

17. Secure the vandal dome cover to the camera.

NOTE 1: Day/Night switcher per sensor in

both AV8185DN and AV8365DN shown in

Image 19.

NOTE 2: All Day/Night switchers

simultaneous switchover, based on the least

(or greatest) illuminated sensor.

Image 19

Image 20

+/- 10°

Set Screws

Day/Night Switcher

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

8 | Page

H.264 Day/Night SurroundVideo

Pendant Mount SV-CMT Installation Instructions

Inside the box:

A. Pendant pole

B. Top shield

C. Pendant Mount

D. One double sided hex key

E. Pack of four (4) wood screws and four (4)

dry wall anchors

F. Mounting template

Not included but needed:

#2 Phillips head screw driver

Image 21

Image 22 Image 23

18. Remove Pendant Mount and hardware from

the box.

19. Using the Mounting template, prepare the

mounting provisions for camera installation.

20. Connect top shield, pendant pole and mount

together as shown in Image 22.

NOTE: The thread size of top shield, pendant

pole and mount is 1.5” NPT.

21. Attach pendant mount to the ceiling using the

four wood screws provided or any optional

hardware suitable for the mounting surface.

22. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

23. For installation of the camera shown in Image

23, please reference “Mounting the

Camera”.

Arecont Vision H.264 Day/Night SurroundVideo

Series Installation Manual

9 | Page

H.264 Day/Night SurroundVideo

Wall Mount SV-WMT Installation Instructions

Inside the box:

A. Top shield

B. Wall mount

C. One double sided hex key

D. Pack of four (4) wood screws and four (4)

dry wall anchors

E. Mounting template

Not included but needed:

#2 Phillips head screw driver

Image 24

Image 25 Image 26

24. Remove Wall Mount and hardware from the

box.

25. Using the Mounting template, prepare the

mounting surface.

26. Connect top shield and wall mount as shown

in Image 25.

NOTE: The thread size for Top shield,

pendant pole and mount is 1.5” NPT.

27. Run Ethernet Cable and outside power cable

(if necessary) through the Wall Mount.

28. Attach Wall Mount to the wall using drywall

screws or any optional hardware suitable for

the mounting surface.

29. For installation of the camera shown in image

26, please reference “Mounting the

Camera”.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Arecont Vision

Arecont Vision

Arecont Vision AV12275DN-NL Manual de usuario

Arecont Vision

Arecont Vision D4SO Series Manual de usuario

Arecont Vision

Arecont Vision MicroDome Manual de usuario

Arecont Vision

Arecont Vision ConteraIP Fisheye AV12CPD-236 Manual de usuario

Arecont Vision

Arecont Vision Contera Micro Bullet Manual de usuario

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-08 Manual de usuario

Arecont Vision

Arecont Vision MicroDome AV1455DN-F Manual de usuario

Arecont Vision

Arecont Vision Megaball series Manual de usuario

Arecont Vision

Arecont Vision SurroundVideo G5 Mini Manual de usuario

Arecont Vision

Arecont Vision MegaDome AV1355DN-1HK Manual de usuario

Arecont Vision

Arecont Vision MegaDome 2 Manual de usuario

Arecont Vision

Arecont Vision MicroDome G2 AV1555DN-S Manual de usuario

Arecont Vision

Arecont Vision MicroDome AV2455DN-S Manual de usuario

Arecont Vision

Arecont Vision D4S Series Manual de usuario

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-NL Manual de usuario

Arecont Vision

Arecont Vision AV2100 Manual de usuario

Arecont Vision

Arecont Vision AV08ZMV-300 Manual de usuario

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manual de usuario

Arecont Vision

Arecont Vision D4S Series Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Manual de usuario

Arecont Vision

Arecont Vision MegaDome G3 Manual de usuario

Arecont Vision

Arecont Vision MegaBall 2 Manual de usuario

Arecont Vision

Arecont Vision AV2325DNIR Manual de usuario

Arecont Vision

Arecont Vision AV1255AM Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario