Arec LS-US2 Manual de usuario
LS-US2
Media Station
ENGLISHQuick Installation Guide
AREC Inc.© All Rights Reserved 2021. l www.arec.com
All information contained in this document is Proprietary
LS-US2 Quick Installation Guide
FCC
Federal Communication Commission interference statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: -Reorient or relocate the receiving antenna. -Increase the
separation between the equipment and receiver. -Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. -Consult the dealer or an
experienced radio/TV technician for help.
RF Exposure Warning
The equipment complies with RF exposure limits set forth for an uncontrolled environment. The
antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation
This equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Notice: Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
1
2
LS-US2 Quick Installation Guide
CE
Hereby, AREC Inc., declares that this Media Station is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
LS-US2 Quick Installation Guide
3
Introduction
Specifications
Package Contents
Featuring a compact and stand-alone design, AREC LS-US2 Media Station consists of diverse
features and functionality, including multi-signals capturing, recording synchronously, codec,
streaming online, live broadcasting, and web-based monitor page, providing complete
presentation or lecture capture solution.
Media Station
LS-US2
98mm(L) x 95mm(W) x 55mm(H)
510g
5V
30W (Max.)
0ºC ~ 40ºC / 90%
Supports two video inputs, and up to two USB Cam/
IP Cam/stream signals. And output the transcoded
video to the HDMI port and the DisplayPort.
Product Name
Model Name
Dimension
Weight
Power Requirement
Power Consumption (Max.)
Operating Temperature / Humidity
Maximum normal load description
Quick Installation Guide HDMI to USB dongle
Power AdapterAREC Media Station
USB drive
4
Product Appearance
TOP Panel I/O Panel
1
2
3
4
5
6
7
8
9
10
11
Record Button
USB Storage
Reset Port
Power Button
Power port
USB-In
DP-Out
HDMI Out
Ethernet Port (LAN)
Ethernet Port (WAN)
USB3.0 Micro B Port
NOTE: The LS-US2 can detect and record to USB storage devices using FAT32, NTFS, exFAT, Ext3, Ext4 file
systems.
NO. Name Brief Introduction
Control the Record and Stop function
1.For the external USB storage device*
2.Available for the USB mouse, keyboard and touch devices
3.Available for the USB audio/video input
Reset the device to default settings
When the device is ON, push twice to turn OFF.
Long press 3 seconds to restart.
When the device is OFF, push to turn ON.
5V
1.For the backup USB storage device, system format is needed in
administrator webpage
2.Available for the USB mouse, keyboard and touch devices
3.Available for the USB audio/video inputs
Supports the recording preview, inputs monitoring and mixing
display
Supports the recording preview, inputs monitoring and mixing
display (this output video always comes with graphic tool bar)
For the network camera’s video input or the settings via PC
For the internet access to do live broadcasting or remote device
control
1.For the external USB storage device*
2.Available for the USB mouse, keyboard and touch devices
3.Available for the USB audio/video input
LS-US2 Quick Installation Guide
1
2
7 963
8
10
4
5
11
5
Connection
LS-US2 Quick Installation Guide
network
external hard disk
USB
Speakerphone
Speakerphone
USB cam
USB cam
USB drive
USB Keyboard
USB mouse
USB Keyboard
USB mouse
Power
USB
Video output HDMI
Video output DP
projector
TV
projector
TV
USB Micro B
notebook
IP cam
Interactive Whiteboards
Interactive Whiteboards
Speakerphone
USB cam
USB Keyboard
USB mouse
Interactive Whiteboards
6
Accessing the Administrator pages
Log in Administrator with default username “admin” and password “admin”, then entering
System Administration webpages.
1. Connect HDMI output with a display monitor and use the RJ-45 Ethernet cable to connect an
IP-based network to the WAN port.
2. Connect your PC/NB to be the same network area with the device. Enter the IP address
displayed in the lower right side of the screen in your browser to access the System
Administration webpage.
http://10.2.0.172
http://10.2.0.172
10.2.0.172
LS-US2 Quick Installation Guide
7
Make sure the network camera are connected under the
same IP network (LAN)* and go to the [ Network device
manager ] page. After the scanning is done, click the
Login button and the authentication dialog will pop up.
Enter the username and password of the camera to
complete the authenticationand change the status to
[ OK ]. Then the camera is ready for video input
selection. Select the target camera by its IP address.
For video source of encoder, enter RTSP or RTP
connection URL.
* For instance, the camera and LS-US2 connected under
the same router with the same LAN address.
Setup
Step 1: Set up video input name, video source, PTZ control in [ Video inputs ] of [ Media I/O ].
The capture source can be from USB input, network camera, or encoder input.
If the assigned video source is network camera, a login authentication with the camera
is required firstly in the [ Network device manager ] setup tab of [ Media I/O ].
Router(192.168.0.1)
LS-US2(192.168.0.10)
IP Camera(192.168.0.20)
LS-US2 Quick Installation Guide
LS-US2 Quick Installation Guide
8
Step 2: Set up audio source in [ Audio ] of [ Media I/O ]. Choose the correct USB audio source.
If there are more than 2 USB audio inputs connected to the system, you only could
assign one of them for the recording.
Step3: Set up network configurations in [ Network ] of [ System ], if necessary.
9
LS-US2 Quick Installation Guide
Click the AREClick icon to get the recording preview window.
Choose a proper recording layouts.
Press recording control buttons to start and stop recording.
Start a recording from the top panel
Press [ ] button and recording begins.
Press [ ] button to end a recording.
Start a recording from the APK of iFPD
Consult your iFPD supplier to install the AREClick APK.
Getting start a recording
Run AREClick , input the IP address and click the “start service” button to see the AREClick
icon.
Otros manuales para LS-US2
1
Tabla de contenidos
Otros manuales de Sistema de conferencias de Arec
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
