AOR AR2700 Manual de usuario

Otros manuales para AR2700

1

Tabla de contenidos

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario

Fitting the RU2700 recording option to the AR2700 receiver

The fitting is recommended to be carried out in an experienced specialist receiver

workshop.

1. Removetherear batterycompartment cover

fromthe AR2700 receiver.

2. Removethebatteries (if fitted).

3. Removethetwo black selftapping screws

fromthe lowersectionofthebattery

compartment. Storeina safe place.

4. Removethe two screwsfromtheboththe

left&right sidepanels(only therearcase

halfscrews needberemoved).

5. Easethetwo casehalves apart, becareful not

tostrain the speakerconnecting wires.

Unplugthe speakerconnecting plugfromthe

PCB.

Thefrontcase halfcomprisesof theLCD,keypad,

side keys & speaker.

Therearcase halfcomprisesof thetoppanel, I.F.PCB,

R.F.PCB andbattery compartment.

6. TheI.F.PCBneedsto be removed,be careful notto

damagethe battery connectingleads astheyare

solderedinplace.

Pulloffthe threeknobsfor theVOL,SQL & DIALand

removethe three lockingnuts usingapair oflong nosed

pliersetc.

7. Removethetwo (long)selftapping screwswhich are

holdingthebottom edgeofthe I.F.PCB.

8. LifttheI.F. PCB clearof the cabinet(startby liftingthebottom oftheI.F.PCBso that

thecontrolswill passbackward through thetop panel holes). TheDC leads remain

attachedtothe I.F.PCB sobecareful torestrictmovement toaminimum.

9. Turnthe I.F.PCB up-side-downand referto thediagramoverleaf...

1/2

2/2

10. Fitthe RU2700PCBto connector "CON204"ofthe I.F.PCB, be careful notto

misalignthepins (lookat both endsof the connectorwhen fitted tocheck).

11. Removethe2-pin jumperfrom connector "CON205"of the I.F.PCBandinsert the

2-pinconnectorfrom the RU2700PCB so thattheyellow wire isnearest the edgeof

theconnectorstrip. The threeright hand of"CON205" are notused.

12.Reassemble the receiver.

13. The record / playback facility is used as described in section 13 (page 55) of the

operatingmanual. Ifthe optiondoes not setup straight away(no "REC" flagand no

audio)thenenable theoption using theinformation provided insection 13 (page55)

ofthe operatingmanual.

i.e.Switch0n holdingthe"0" keytoenter engineer mode.

Switch Off again.

Switch On holding the "5" key.

Usetherotary dial to change"Off"to "On" thenpress[ENT]

Thereceiverwill softreset, then willoperate normally. TESTIT!

Note: If the above is not carried out, the set's audio will be muted!!!

END

AOR LTD, 2-6-4 Misuji, Taito-ku, Tokyo 111, JAPAN

Tel: 03 3865 1681