AND PLUSCONNECT UC-350CNBLE Manual de usuario
Instruction Manual
Safety Information E-2
Overview E-3
Initial Startup E-4
Connecting to Mobile Device
(Pairing) E-5
Start Measuring E-7
Ofine Measurement E-9
Select Measurement Unit E-9
Manage Your Health E-10
Troubleshooting E-11
Specications E-12
Maintenance E-14
Warranty E-15
PLUSCONNECT
Wireless Weight Scale
UC-350CNBLE
Thank you very much for selecting the A&D Medical PLUSCONNECT Wireless
Weight Scale UC-350CNBLE. Please do read the user manual carefully and
thoroughly so as to ensure the safe usage of this product, and keep the manual
well for further reference in case you have problems.
E-2
Safety Information
Your Scale and Its Environment
To ensure your safety as well as the service life of your scale, please avoid
using the scale under the following circumstances:
• Slippery oor such as tile oor
• Jumping onto the platform immediately after bath or with wet feet
• Near a cell phone or microwave oven
Avoid storage in the following locations:
• Where there is water
• Where the device may be exposed to extreme temperatures, humidity, moisture,
direct sunlight, dust, or salt air
• Where there is risk of shock or drop
• Where you store chemicals or full of corrosive gases
• Where in reach of infants or children
Efcient Use of Your Scale
To ensure the accuracy of measurement, please follow the below
instructions when you start the measurement.
• Place the scale on a at, hard surface. Soft surface such as carpet will affect the
performance of the scale.
• Avoid measurement immediately after strenuous exercise, sauna or bath,
drinking, and dinning.
• Always start measurement in the same time slot and on the same scale located
on the same at, hard surface.
E-3
Overview
Device Components
Includes:
• Weight Scale UC-350CNBLE
• 4 x AAA Batteries (1.5V each)
• User Manual
• Quick Start Card
LCD Display
LCD display
DOWN Button
SET Button
UP Button
UNIT and Pair-up
Activation Button Sensor
Battery Compartment
Pound
Kilogram
Successful Bluetooth Connection
Data transmitting/pending to transmit
to wireless wellness system
Low Battery
E-4
Initial Startup
Insert the Batteries
• Open the battery door in the back of the scale.
• Insert the batteries (4 x 1.5V AAA) into the battery
compartment according to the polarity indications
marked inside the compartment.
* The digits “ ” will be shown on the LCD.
• Close the battery door and wait until the digits “ ”
are shown on the LCD.
CAUTION
• When the symbol appears, the device will power off. Then you shall
replace with a new set of batteries. Please replace all four batteries at the
same time. Do NOT mix the old batteries with the new ones.
• Worn batteries are hazardous waste. Do NOT dispose of them together with
the household garbage. Please refer to the local ordinances and recycling
instructions regarding disposal of the worn batteries and scrapped device.
• If you do not intend to use this unit for a prolonged period of time, it is
advisable to remove the batteries before storing.
E-5
Connecting to Mobile Device (Pairing)
Download the “A&D Connect” app
Download the free “A&D Connect” app from the App Store or Google play.
With the advanced Bluetooth®4.0 technology applied, the mobile or portable
equipments, which are equipped with Bluetooth®function in line with BLE Technical
Speci cations established by global organization Bluetooth®SIG, are capable to
receive your personal health data.
Account Registration and Device Setup
Create your account following the app instruction or continue as a guest.
Guest Mode
Log in as guest user. Reading
is saved on device memory
but not in your account
Account Registration
Create an account with
username and password.
The app will save and
track data on your account
and calculate your BMI
UC-350BLE
weight scale
In the Device Setup screen, select UC-350BLE to get the app in pairing mode with
the scale.
E-6
Symbol and symbol
will be shown on the scale LCD
alternatively, indicating pair-up
is proceeding.
If SUCCEED, symbol will be
shown on the scale LCD.
If FAIL, symbol “E1” will be shown
on the LCD. (Please refer to
Troubleshooting for more details.)
Pair-Up
• Turn on Bluetooth®and the app. Make sure both are ON when pair-up is
proceeding.
• Press and hold “UNIT” button in the back of the scale to start pair-up.
UNIT button
On the app, select User ID among
P1 to P7.
NOTE: Remember your “P#”
to ensure data is stored under
correct User.
Connecting to Mobile Device (Pairing)
E-7
Start Measuring
Initializing Your Scale
1. Position the scale on a at, hard surface. Carpeted or
uneven oors may affect accuracy.
2. Press the platform centre and remove your foot.
3. “0.0” will be displayed.
4. The scale will switch off and is now ready for use. This
initialization process must be repeated if the scale is
moved. At all other times step straight on the scale.
Setting the User ID and Start Measuring
• Press “SET” button or when the LCD displays 0.0, press and hold “SET” button
for about 3s to select your “P#”.
• Once “P1” ashes, press the function button or to select your “P#” among P1
to P8. Press “SET” button to lock it. Once the initial User ID is set up, a single user
doesn’t have to repeat this process each time because the scale will remember you.
• After setting your “P#”, step on the platform when the scale displays “0.0”. Stand
still and keep full contact with the scale until the unit (lb/kg) stops ashing. Then
the weight is locked.
• When your scale is successfully paired with your smartphone and the Bluetooth
is ON, it will process data transmission automatically. (Please refer to Data
Transmission for more details.)
Be sure to select your “P#” on the scale.
Guest User should select “P8”.
If you forget your “P#”, conrm in the app dashboard.
Your “P#” is displayed below the scale illustration.
Beep Beep
E-8
Start Measuring
Data Transmission
• Once the Weight Scale UC-350CNBLE is successfully
paired-up with your smartphone, please open the
“A&D Connect” app and turn on your Bluetooth.
Keep smartphone and scale in transmission distance.
Step on the scale and take a measurement. Once
the measurement is nished the data is automatically
transferred to the app.
• The symbol will disappear after
successful data transmission,
and you may check your personal
health data stored in your
smartphone.
• If the data is not transmitted to a
paired phone, the symbol will
remain. The pending measurement
data will be temporarily kept in
the scale and transmitted to your
smartphone when next connection
is complete.
Note: When the data transmission is successful, the device will shut down automatically 3 seconds later.
Multiuser
Up to 8 people can use and store readings on the weight scale (7 registered users
and 1 guest can share the scale).
• To add new users, select User ID that is not assigned already in the Device
Setup process on the app (pg. E-5 and E-6). If all 7 User IDs are occupied, you
can overwrite one by simply selecting it.
• Be sure to select the correct “P#” on the app and the scale for each user.
Guest Users should select “P8”.
• Once the correct User ID is selected, follow the steps for Start Measuring.
Data transmitting
Data ready to transmit to
the app:
• If SUCCEED, the symbol
disappears;
• If FAIL, the symbol remains.
E-9
Ofine Measurement
Even when you don’t have your phone, the weight data is stored in your ID memory
and transmitted next time the scale is connected with your phone (max 30 memory).
Be sure to select your “P#” on the scale. Guest Users should select “P8”.
1. Step onto the scale platform and remain still while the scale computes your
weight. Keep full contact with the scale until the unit (lb/kg) stops ashing.
2. A beep sound will indicate to step off and the scale will display your weight value.
3. The scale will automatically turn off after a few seconds.
Select Measurement Unit
Changing Measurement Unit
The default measurement unit is “lb”.
You may press “UNIT” button on the
back of the scale to choose among
kilogram and pound.
CAUTION
• Please put the scale on at hard ground when nishing the unit selection.
Wait for a few seconds, then you may start measuring. If there is not any
operation in weighing mode, the scale will turn off in a few seconds.
Beep Beep
Tabla de contenidos
Idiomas:
Otros manuales de Escala de AND
AND
AND FZ-i Series Manual de usuario
AND
AND UC-324TMW Manual de usuario
AND
AND GX-L Series Manual de usuario
AND
AND HT-300CL Manual de usuario
AND
AND PR-5 Manual de usuario
AND
AND EJ-120 Manual de usuario
AND
AND HV-15KGL Manual de usuario
AND
AND GX-M Series Manual de usuario
AND
AND EK-610j Manual de usuario
AND
AND SJ-3000WP/-BT Manual de usuario
AND
AND HV-CWP Series Manual de usuario
AND
AND HL-200 Manual de usuario
AND
AND UC-324NFC Manual de usuario
AND
AND UC-352BLE Manual de usuario
AND
AND UC-324ANT Manual de usuario
AND
AND SJ-WP Series Manual de usuario
AND
AND UC-252 Manual de usuario
AND
AND HV-CWP Series Manual de usuario
AND
AND HR-60 Manual de usuario
AND
AND PLUS CONNECT UC-350BLE Manual de usuario
