AMX Camrobotics Manual de usuario
Camrobotics by AMX
INSTRUCTION MANUAL
Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free from defects in material and
workmanship under normal use for a period of three years from date of purchase from
AMX, with the following exceptions. Electroluminescent and LCD control panels are
warranted for a period of three years, except for the display and touch overlay
components which are warranted for a period of one year. Disk drive mechanisms,
pan/tilt heads, power supplies, modifications, MX Series products, and KC Series
products are warranted for a period of one year. Unless otherwise specified, OEM and
custom products are covered for a period of one year. AMX software products are
warranted for a period of 90 days. Batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from AMX or an authorized AMX
dealer. Consumers should inquire from selling dealer as to the nature and extent of the
dealer’s warranty, if any.
AMX is not liable for any damages caused by its products or for the failure of its
products to perform, including any lost profits, lost savings, incidental damages, or
consequential damages. AMX is not liable for any claim made by a third party or made
by you for a third party.
This limitation of liability applies whether damages are sought, or a claim is made,
under this warranty or as a tort claim (including negligence and strict product liability),
a contract claim, or any other claim. This limitation of liability cannot be waived or
amended by any person. This limitation of liability will be effective even if AMX or an
authorized representative of AMX has been advised of the possibility of any such
damages. This limitation of liability, however, will not apply to claims for personal
injury.
Some states do not allow a limitation of how long an implied warranty lasts. Some states
do not allow the limitation or exclusion of incidental or consequential damages for
consumer products. In such states, the limitation or exclusion of the Limited Warranty
may not apply to you. This Limited Warranty gives you specific legal rights. You may
also have other rights that may vary from state to state. You are advised to consult
applicable state laws for full determination of your rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES
NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. AMX EXPRESSLY DISCLAIMS ALL
WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED
TO THE TERMS OF THIS LIMITED WARRANTY.
Camrobotics Table of Contents i
Table of Contents
Introduction ............................................................................ 1
Overview 1
Features 2
AXB-EM232 2
AXP-DTC 3
AXB-CAM 3
CAM-1000 3
PS2.8 4
System Application 4
How to Use this Manual 6
Installation.............................................................................. 7
Overview 7
Pre-installation 7
Connecting the CAM-1000 to the AXB-CAM 8
Preparing captive wires 9
Mounting the CAM-1000 10
Operation .............................................................................. 11
Overview 11
Camera Selection 11
Iris Controls 12
Zoom/Focus Control 12
Pan/Tilt Control 12
Speed Control 13
Limit Stops 13
Adjusting the pan limit stops 13
Adjusting the tilt limit stops 14
Preset Operation 15
Programming the presets 15
Recalling the presets 16
Reversing the Joystick/POT Direction 16
Specifications....................................................................... 19
Overview 19
AXP-DTC 19
CAM-1000 20
ii Table of Contents Camrobotics
Technical Support ................................................................ 23
Overview 23
Camrobotics Introduction 1
Introduction
Overview
Camrobotics by AMX offers fully modular, programmable camera control systems.
The Camrobotics application (Figure 1) described in this document includes the
following AMX products:
AXB-EM232 Enhanced Master/RS-232 Controller, a bus device that functions
like an AMX Enhanced System Master Card in a single compact enclosure and
has CAMROBOTICS-specific AXCESS programming
AXP-DTC Desktop Camera Panel, a camera positioning panel that provides
joystick and pushbutton control
AXB-CAM Camera Controller, a programmable AXlink or RS-232 device that
can control a wide variety of motorized pan/tilt heads and camera lenses
CAM-1000 Pro Pan/Tilt Head, a motorized pan/tilt camera head
PS2.8 12 VDC, 2.8 A Power Supply provides regulated switching of 110/220
VAC input
2Introduction Camrobotics
AXB-CAM
PS2.8
AXB-CAM
PS2.8
AXB-CAM
PS2.8
AXB-EM232
AXP-DTC
12 VAC
CAM-1000
tripod mount
CAM-1000
wall mount with
WM-CAM
(optional)
CAM-1000
surface mount
Features
The following are the features of the Camrobotics application.
AXB-EM232
Supports RS-232-, RS-422-, and RS-485-controlled devices, such as audiovisual
and computer-based devices, as well as AXlink devices
Supports hardware handshaking and asynchronous data communication
standards
Includes a 12 VDC power supply
Figure 1
Camrobotics application
Camrobotics Introduction 3
Stores program commands in 64K of battery-protected memory that can be
expanded to 256K
AXP-DTC
Is a professional joystick-assisted camera operator control interface
Displays positive status feedback from illuminated pushbuttons
Emulates analog control for lens iris and joystick speed adjustment
Stores and recalls up to 144 preset positions, 24 per camera station, for up to 6
camera stations using shot, mode selection, and camera station pushbuttons
AXB-CAM
Controls pan/tilt voltage from external supply (6 VDC to 24 VDC, 1 A)
Controls pan/tilt voltage (-12 VDC to 12 VDC, 150 mA)
Controls zoom and focus voltage (-12 VDC to 12 VDC, 150 mA)
Communicates with most PCs through RS-232 port (300 to 38,400 baud)
Has eight adjustment potentiometers (POTs) for setting the center and range
voltages for pan, tilt, zoom, and focus operations
Has five easily accessible calibration test points for checking control voltage
settings for pan, tilt, zoom, and focus operations
CAM-1000
Handles a camera load of up to 18 pounds (8.2 kg)
Adjusts to a variety of camera/lens centerlines
Installs using four pre-tapped holes (1/4 x 20 thread) or standard camera
tripod mount (3/8 - 16 thread)
Limits pan and tilt range using adjustable external stops (270-degree
maximum pan, 90-degree maximum tilt)
Operates on 12 to 24 VDC power
Delivers precise motion control and position feedback for precise preset
repeatability
4Introduction Camrobotics
PS2.8Provides regulated 12 VDC power up to 2.8 A
Automatically switches for 110/220 VAC operation
Has overload protection
System Application
The AXB-EM232 is an AMX Enhanced System Master Card in a single compact
enclosure. It is fully compatible with the AXCESS Control System and can be used
either as a stand-alone device or with other AMX bus controllers. The AXB-EM232
runs complete AXCESS programs and controls other AXlink components and two
devices using RS-232 as a control protocol. It can also control devices using RS-422
or RS-485 protocols.
The standard program configuration of this Camrobotics system application
(Figure 2) controls up to six camera stations. An AXB-CAM, CAM-1000, and PS2.8
are required for each station. There is also a provision for RS-232/422 interfacing
with a host computer through the AXB-EM232 or directly to the AXB-CAM.
The system software assumes a standard configuration using videoconference-style
lenses, including Fujinon BMD and Canon KTSA format lenses, which require no
modification. If the system includes optional components and software—such as
CCTV-type lenses (direct DC drive and reference POTs), RS-232-controlled lenses, or
video switching—refer to the documentation that came with those components and
software applications or contact their manufacturers for additional information.
Camrobotics Introduction 5
AXP-DTC
AXB-CAM (rear view)
AXB-EM232 (rear view)
PS2.8 (see note)
Lens
CAM-1000
(surface mount)
Camera
AXlink cable
120 VAC
Note
A separate power supply is only
required in applications controlling
more than one camera station, as in
Figure 1. For applications using only
one camera station, the power supplied
from the AXP-DTC via the +12 V wire
in the AXlink is sufficient to power the
three camera station components, the
AXB-EM232, AXB-CAM, and
CAM-1000.
The AXP-DTC provides a traditional joystick and illuminated pushbutton mode of
control for camera positioning and lens control. Two dual-axis, proportional-speed
joysticks with oversized handles furnish comfortable, precision pan, tilt, zoom, and
focus control. Adjustable iris control with automatic and manual modes is available
as well. You can select up to six camera stations as well as store and recall eight
preset shots for each of three modes per camera station. The three mode buttons can
provide a variety of features through AMX custom programming, including
selection of optional banks of cameras or activation of routing commands to a video
switcher.
The AXB-CAM is an AXlink device that can control a wide variety of motorized
pan/tilt heads and camera lenses that use low-current (5 VDC to 12 VDC) and/or
high-current (-24 VDC to 24 VDC) control voltages. The AXB-CAM uses 8-bit (256
Figure 2
System application
6Introduction Camrobotics
steps) and 10-bit (65,535 steps) precision-control processing, and is equipped with a
lithium battery that protects stored memory.
The CAM-1000 is a motorized pan/tilt head designed for precision, preset camera
positioning. The motor drives are optimized for 0 to 12 VDC control and accept 0 to
24 VDC as well for universal system compatibility. Precision POTs provide pan and
tilt position sensing for presets.
How to Use this Manual
This manual comprises the following sections:
Installation Describes installation of the CAM-1000.
Operation Describes basic operations of the AXP-DTC.
Specifications Describes the specifications for the AXP-DTC and the
CAM-1000.
Technical Support Lists the telephone numbers to call for AMX
technical support.
For complete information about pre-installation settings, installation, and
programming of the AXB-EM232 and AXB-CAM, refer to the following AMX
manuals:
Enhanced Master RS-232 Instruction Manual, 032-004-0004
AXB-CAM Camera Controller, 032-004-1212
Tabla de contenidos
Otros manuales de Software de AMX
AMX
AMX NETLINX STUDIO V2.4 Manual de usuario
AMX
AMX TPDESIGN4 V2.5 Manual de usuario
AMX
AMX MAX-MMS-01S Manual de usuario
AMX
AMX NSS-VOTE Manual de usuario
AMX
AMX RMS Manual de usuario
AMX
AMX IREdit Manual de lista de piezas
AMX
AMX NSS-VOTE PROGRAMMER Manual
AMX
AMX I!-FTPSENDER Manual de usuario
AMX
AMX VISUALARCHITECT CONTENT DATABASE EDITOR Manual de usuario
AMX
AMX CAFE DUET STANDARD NETLINX API (SNAPI) COMPONENTS AND... Manual de usuario
AMX
AMX USB LAN Driver USBLAN Manual de lista de piezas
AMX
AMX DESIGN XPRESS HOME THEATER V1.3 - ON SITE INSTALLER... Manual de usuario
AMX
AMX VPXImport Manual de usuario
AMX
AMX AXT-CA10 Manual de usuario
AMX
AMX AXWire Manual de usuario
AMX
AMX TPDESIGN3 V3.16 Manual de usuario
AMX
AMX AXT-CA10 Manual de usuario
AMX
AMX Design XPress Manual de usuario
AMX
AMX I!-PCLINK WEB Manual de usuario
AMX
AMX Podcast Manual de usuario
Manuales populares de Software de otras marcas
PS Audio
PS Audio PowerPlay Manual del propietario
Brady
Brady LOCKOUT PRO 3.0 Manual de servicio
Avaya
Avaya Interaction Center Manual de usuario
Texas Instruments
Texas Instruments TI-83 Plus Silver Edition Manual
Novell
Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario
Oracle
Oracle Application 9i Manual de usuario
Acer
Acer RDM Manual de usuario
Canon
Canon Vixia HF21 Manual de usuario
Canon
Canon ZR950 Manual de usuario
Samsung
Samsung Auto Backup Manual de usuario
Polycom
Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento
Brocade Communications Systems
Brocade Communications Systems Brocade 8/12c Manual de usuario