AMD XILINX T2 Telco Manual de usuario
T2 Telco Accelerator Card
Installaon Guide
UG1527 (v1.0) June 15, 2022
Xilinx is creating an environment where employees, customers, and
partners feel welcome and included. To that end, we’re removing non-
inclusive language from our products and related collateral. We’ve
launched an internal initiative to remove language that could exclude
people or reinforce historical biases, including terms embedded in our
software and IPs. You may still find examples of non-inclusive
language in our older products as we work to make these changes and
align with evolving industry standards. Follow this link for more
information.
Table of Contents
Chapter 1: Introduction.............................................................................................. 4
Minimum System Requirements and Setup............................................................................ 5
Configuring the PCIe Slot Bifurcation.......................................................................................5
Chapter 2: Card Information and Installation............................................. 10
Safety Instructions.................................................................................................................... 10
Electrostatic Discharge............................................................................................................. 10
Before You Begin.......................................................................................................................10
Installing the Card.....................................................................................................................11
Chapter 3: Installing Additional Software......................................................12
Chapter 4: T2 Factory Installed Image..............................................................13
Flashing the Images in QSPI Using flash_app....................................................................... 13
Chapter 5: T2 Base Software Design.................................................................. 15
T2 Base Software Design on the ZU48 Zynq UltraScale+ RFSoC......................................... 15
T2 Skeleton Design Package.................................................................................................... 16
Chapter 6: Running the Tests.................................................................................18
ZU48 Zynq UltraScale+ RFSoC PCIe Loopback Test...............................................................19
DDR Read/Write Tests...............................................................................................................21
Test Application Guide and Address Map.............................................................................. 24
Chapter 7: Next Steps.................................................................................................25
Chapter 8: Dependencies/Known Issues.........................................................26
Chapter 9: Programming the Devices Using JTAG......................................27
Flashing the Images to ZU48 Zynq UltraScale+ RFSoC QSPI Using the Vitis
Environment..........................................................................................................................30
Programming the Bitstreams Directly ...................................................................................31
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 2
Send Feedback
Appendix A: Regulatory Compliance Statements...................................... 33
FCC Class A Products.................................................................................................................33
Safety.......................................................................................................................................... 33
EMC Compliance........................................................................................................................34
FCC Class A User Information..................................................................................................34
VCCI Class A Statement............................................................................................................ 35
Appendix B: Additional Resources and Legal Notices............................. 36
Xilinx Resources.........................................................................................................................36
Documentation Navigator and Design Hubs.........................................................................36
References..................................................................................................................................36
Revision History.........................................................................................................................37
Please Read: Important Legal Notices................................................................................... 37
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 3
Send Feedback
Chapter 1
Introduction
This document provides hardware and soware installaon procedures for the T2 Telco
accelerator card along with a guide to the T2 skeleton design. The skeleton design is created
specically for the 16 nm Zynq® UltraScale+™ RFSoC device on the T2 card, and provides
connecons and soware to validate the main interfaces of the board.
Figure 1: T2 Telco Accelerator Card
The Xilinx® T2 Telco accelerator card is a PCI Express® (PCIe) Gen4 x16 compliant card featuring
the 16 nm Zynq UltraScale+ RFSoC device. The T2 form factor is half height, half length (HHHL)
and single slot, with a PCIe Gen4 x16 interface that is x8x8 bifurcated providing x8 links from the
host to the Zynq UltraScale+ RFSoC device. Target applicaons for the T2 card include the
following:
• 4G LTE and 5G NR high-PHY lookaside acceleraon (supporng 3GPP split opon 7–2x)
• 5G layer 1 (L1) high-PHY lookaside acceleraon
• 4G LTE and 5G NR inline acceleraon of L1 funcons (supporng 3GPP split opon 7–2x) for
up to 4TRX
Chapter 1: Introduction
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 4
Send Feedback
The T2 card turns a standard server into a virtual baseband unit with the performance, low
latency, and power eciency needed for O-RAN 5G deployments. The turnkey soluon enables
operators, system integrators, and OEMs to get to market quickly and to simplify the deployment
of services at the edge.
Minimum System Requirements and Setup
The minimum system requirements for running a T2 Telco accelerator card are shown below:
Table 1: Minimum System Requirements
Component Requirement
Motherboard PCI Express 4.0 compatible with one dual-width x16 slot.
System power supply 75W through a PCI Express slot connection
Operating system Linux, 64-bit:
CentOS 7 and 8
Ubuntu 16, 18, and 20
System memory and CPU cores For deployment installations, a minimum of 16 GB plus
application memory requirements is required. For
development installations, a minimum of 64 GB of device
memory is required, but 80 GB is recommended.
A minimum of 16 logical cores is required.
Internet connection Required for downloading drivers and utilities.
Hard disk space Satisfy the minimum system requirements for your
operating system.
Auxiliary power supply No auxiliary power supply is required because the T2 card
cannot boot standalone.
Vitis™ application acceleration development flow The Vitis™ application acceleration development flow is not
currently supported.
The T2 Telco accelerator card is intended for deployment on most servers. Thermal tesng has
been conducted on a Dell R640. Funconal tesng has been conducted on a number of
addional servers including Dell R730 and R740.
Configuring the PCIe Slot Bifurcation
Perform the following steps to enable bifurcaon in the slot where the T2 card has been
inserted. This is required for the T2 card to work properly.
Note: These steps are for a single T2 card deployment.
1. Power on the server. The output on the monitor is shown below.
Chapter 1: Introduction
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 5
Send Feedback
2. Wait unl the monitor lists the shortcut keys, so you can navigate into the setup. The screen
with the shortcut keys looks like the following gure.
3. Press F2 to open the system setup sengs.
4. In the System Setup screen, select the System BIOS opon as shown below.
Chapter 1: Introduction
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 6
Send Feedback
7. Click the required slot to change bifurcaon.
8. Click Default Bifurcaon and select x8x8 or x8 Bifurcaon. This enables the T2 card in the
slot with the correct communicaon over the PCI. Click the Back buon in the lower right
hand side of the screen.
Chapter 1: Introduction
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 8
Send Feedback
9. Return to the System BIOS screen and click the Back buon again.
10. In the System BIOS Sengs main menu screen, click Finish.
11. A popup window will show a warning, as shown below. Click Yes to save the changes you
made.
12. Click the Finish buon again.
13. When the system has rebooted, check to see if the T2 card has been detected using the
lspci | grep Xilinx command.
Chapter 1: Introduction
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 9
Send Feedback
Chapter 2
Card Information and Installation
Safety Instructions
To ensure your personal safety and the safety of your equipment:
• Keep your work area and the computer/server clean and clear of debris.
• Before opening the computer/system cover, unplug the power cord.
Electrostatic Discharge
Electrostac discharge (ESD) can damage electronic components when they are improperly
handled, and can result in total or intermient failures. Always follow ESD prevenon procedures
when removing and replacing components. To prevent ESD damage:
• Use an ESD wrist or ankle strap and ensure that it makes skin contact. Connect the equipment
end of the strap to an unpainted metal surface on the chassis.
• Avoid touching the card with your clothing. The wrist strap protects components from ESD on
the body only.
• Handle the card by its bracket or edges only. Avoid touching the printed circuit board or the
connectors.
• Put the card down only on an anstac surface such as the bag supplied in your kit.
• If you are returning the card to Xilinx product support, place it back in its anstac bag
immediately.
Before You Begin
IMPORTANT! The T2 Telco accelerator card is a delicate and sensive electronic device and should be
installed by a qualied technician only. This equipment is intended for installaon in a restricted access
locaon.
Chapter 2: Card Information and Installation
UG1527 (v1.0) June 15, 2022 www.xilinx.com
T2 Telco Accelerator Card Installation Guide 10
Send Feedback
Otros manuales para XILINX T2 Telco
1
Tabla de contenidos
Otros manuales de Hardware de computadora de AMD
AMD
AMD 790GX Manual de usuario
AMD
AMD M56 Manual de usuario
AMD
AMD SB600 Manual del producto
AMD
AMD Athlon Manual de usuario
AMD
AMD Athlon Manual de usuario
AMD
AMD B59 Manual de usuario
AMD
AMD ATI FireMV 2400 Manual de usuario
AMD
AMD ATHLON K Instrucciones de uso
AMD
AMD LE-366 User's Manual de usuario
AMD
AMD AX1800DMT3C - Athlon XP 1.53 GHz Processor Manual de usuario
AMD
AMD 770 Manual de usuario
AMD
AMD Athlon Processor x86 Manual de usuario
AMD
AMD Richland Manual de usuario
AMD
AMD Opteron 4200 Series Manual de usuario
AMD
AMD AMD Athlon 64 Manual de instrucciones
AMD
AMD Hudson M1 Chipset Manual de usuario
AMD
AMD FM2+ Manual de usuario
AMD
AMD Turion 64 Manual operacional
AMD
AMD Geode LX 800 Manual de usuario
AMD
AMD MulTView ALL-IN-WONDER 9700 PRO Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
