Amano PIX-15 Manual de usuario

PIX-15

Electronic Time Recorder

Operation Manual

Thank you…

for purchasing another fine product from

Amano Cincinnati, Inc.

Important

Note that the government standard for Daylight Saving Time (DST) is

subject to change. Your clock is factory-set for correct DST based upon

when it was manufactured, but any revision to DST begin or end dates

may require updating the system-set DST calendar.

If you live in Arizona, Hawaii, parts of Indiana, or any other area that

does not use Daylight Saving Time, refer to this document’s DST

settings instruction for details regarding disabling the DST function.

Do not return this clock to the retailer. If you have any questions or need

assistance, please call us toll free at:

1-800-253-9836

Proprietary Notice

This document contains proprietary information and such information

may not be reproduced in whole or part without the written permission

from Amano Cincinnati, Inc. 140 Harrison Ave., Roseland, New Jersey

07068. Amano Cincinnati, Inc. reserves the right to make equipment

changes and improvements, which may not be reflected in this

document.

We recommend that this document be read in its entirety before any

attempt is made to operate the equipment.

Need Ribbons, Keys and Accessories?

Visit

www.amano.com

Call - (800)-253-9836

Amano PIX-15 Operation Manual 1

Your PIX-15

Removing the Cover and Packing Materials

Note: You must remove the packaging spacers from the printer block and the

printer carriage before attempting to use your PIX-15.

1. Lift the printer block and remove the spacer.

hole

Print Window

Digital Clock

Margin

Reset Switch

(on bottom)

Change

Button

Enter

Button

Print Slot

Spacer

Printer

Block

Spacer

2 Amano PIX-15 Operation Manual

2. Insert the key provided and turn clockwise to open the case. Lift

the cover to remove.

3. Remove the spacer between the Ribbon Cartridge and the Printer

Carriage.

4. Re-install the cover. Your PIX-15 is ready for use!

Closed

Remove

Spacer

Amano PIX-15 Operation Manual 3

Before You Change Any Settings

Take a moment to familiarize yourself with the items explained below.

The Front Panel

LCD Display Window CHANGE Button ENTER Button

Normally, the Display Window shows the date and time. When you use

the Quick Set or Program Mode to change the settings of the PIX-15, the

instructions to change the clock are shown in this window.

The two buttons on the front panel are used to navigate through the

Quick Set and Program Mode to change the clock’s settings.

The left button is marked with a ◄symbol. It is called the

CHANGE Button. Use this button to change the information shown on

the display when you are in the Quick Set or Program Mode.

The right button is marked with a ●symbol. It is called the

ENTER Button. When you are in the Quick Set or Program Mode, use

this button to enter the setting shown on the display into memory.

The Reset Button

The RESET Button (which

is long) is located in the

right lower corner on the

bottom of the clock.

Please Note:

You do not need the key to set the time or to program the clock!!

However, you do need the key to change the ribbon, or mount the clock

on the wall (see page 9).

If you have any questions, please call 1-800-253-9836.

4 Amano PIX-15 Operation Manual

Making a Test Print

1. Plug in the power cord.

2. Insert a piece of paper or time card into the PIX-15. The clock will

automatically print YEAR, MONTH, DATE and TIME with AM or PM

(in Pacific Time).

Note: The PIX-15 will automatically adjust for Daylight Saving Time. If these

conditions are unsatisfactory, you must change the program settings.

3. If the imprint is satisfactory, and you are going to place the PIX-15 on

a desk, table, or shelf, the PIX-15 is ready to be used.

4. In order for you to set the time or change the print style, you must

enter a code. Choose a code from the list below that best fits your

needs. Continue to the next page for instructions on how to enter your

code.

Code Print Style Print Direction

6510 DAY, 12H, 60th Right Side Printing

6210 DAY, 24H, 10th Right Side Printing

6810 DAY, 24H, 100th Right Side Printing

6520 DATE, 12H, 60th Right Side Printing

6620 DATE, 24H, 60th Right Side Printing

6820 DATE, 24H, 100th Right Side Printing

6530 MONTH, DATE, 12H, 60th Right Side Printing

6630 MONTH, DATE, 24H, 60th Right Side Printing

6830 MONTH, DATE, 24H, 100th Right Side Printing

6570 YEAR, MONTH, DATE, 12H, 60th Right Side Printing

6071 YEAR, MONTH, DATE, RCV’D Right Side Printing

6072 YEAR, MONTH, DATE, SENT Right Side Printing

6073 YEAR, MONTH, DATE, FAX’D Right Side Printing

6074 YEAR, MONTH, DATE, VOID Right Side Printing

6075 YEAR, MONTH, DATE, PAID Right Side Printing

6076 YEAR, MONTH, DATE, CFM’D Right Side Printing

6077 YEAR, MONTH, DATE, APR’D Right Side Printing

6078 YEAR, MONTH, DATE, CMPL’D Right Side Printing

6079 YEAR, MONTH, DATE, ORIGN Right Side Printing

6070 YEAR, MONTH, DATE, FILE Right Side Printing

Note: If you cannot locate the desired print style from the above list, please

Amano PIX-15 Operation Manual 5

Entering the Clock Program

The following steps describe how to get into the clock program. To set

the print style and time, use a code chosen from the list (see page 4).

For example, the following directions use code 6570.

1. Entering a Code

a. Press and hold the RESET button on the bottom of the

clock. (Refer to page 3 for location.)

b. While holding down the RESET button, press and hold

the ●right button on the front panel.

c. While holding the ●right button, release the RESET

button.

d. Next release the ●right button and Pro9 will

flash in the display.

e. Tap the ●right button. The display will show

0000, and the first digit will flash.

f. Tap the ◄left button until the first number of

your code appears, then tap the ●right button

and the second digit will flash.

g. Tap the ◄left button until the second number

of your code appears, then tap the ●right

button and the third digit will flash.

h. Tap the ◄left button until the third number of

your code appears, then tap the ●right button

and the fourth digit will flash.

i. Tap the ◄left button until the fourth number of

your code appears, then tap the ●right button.

j. With the display flashing all four digits,

tap the ●right button again and Pl dA Ewill display.

6 Amano PIX-15 Operation Manual

2. Setting the Year, Month and Date

a. With the display flashing Pl dA E,

tap the ●right button and the display will show

year, month, and date.

b. Press the ◄left button until the correct year

appears, then tap the ●right button.

c. Press the ◄left button until the correct month

appears, then tap the ●right button.

d. Press the ◄left button until the correct date

appears, then tap the ●right button.

e. When the display flashes the correct year, month

and date, tap the ●right button.

f. When the display flashes Pl dA E, tap the

◄left button to move to Setting the Time

(P2 CLoc will display)

3. Setting the Time

When setting the time, you must use a 24 hour and 60 minute format

(i.e., 1:00 pm = 13:00). This will NOT make the clock print in

military time, but simply tells the clock am from pm.

a. With the display flashing P2 CLoc, tap

the ●right button.

b. The small “12” will flash. Tap the

●right button again.

c. The hour digits will flash. Tap the

◄left button until the correct hour

appears. Remember to use a 24-hour

format (2:00 pm = 14:00). Then tap the

●right button.

d. The minute digits will flash. Tap the

◄left button until the correct minutes

appear, then tap the ●right button.

e. When the display flashes P2 CLoc, tap the

◄left button to move to the beginning of

the Daylight Saving Setting (P3 bdLt will display).

Amano PIX-15 Operation Manual 7

4. Setting the Beginning Date of Daylight Saving Time (DST)

Note: The government standard for DST is subject to change. Your clock is

factory-set for correct DST based upon when it was manufactured, but any

revision to DST begin or end dates may require updating the system-set

DST calendar.

The steps below change the begin date for DST. Updating the begin date

for DST needs to be done just one time*, since the clock’s rolling calendar

function will auto-calculate the begin date for each year thereafter. To

change the end date for DST, refer to the next section.

a. With the display flashing P3 bdLt, tap the

●right button.

b. Tap the ◄left button until the correct year

appears, then tap the ●right button.

c. Tap the ◄left button until the correct month

appears, then tap the ●right button.

d. Tap the ◄left button until the correct date

appears, then tap the ●right button.

e. With the display flashing the correct year, month

and date, tap the ●right button.

f. With the display flashing P3 bdLt, tap the

◄left button to move to the end of the Daylight

Saving Setting (P4 EdLt will display).

5. Setting the End Date of Daylight Saving Time (DST)

Note: The government standard for DST is subject to change. Your clock is

factory set for correct DST based upon when it was manufactured, but any

revision to DST begin or end dates may require updating the system-set

DST calendar.

The steps below change the end date for DST. Updating the end date for

DST needs to be done just one time, since the clock’s rolling calendar

function will auto-calculate the end date for each year thereafter. To

change the begin date for DST, refer to the previous section.

a. With the display flashing P4 EdLt, tap the

●right button.

b. Tap the ◄left button until the correct year

appears, then tap the ●right button.

c. Tap the ◄left button until the correct month

appears, then tap the ●right button.

8 Amano PIX-15 Operation Manual

d. Tap the ◄left button until the correct date

appears, then tap the ●right button.

e. With the display flashing the correct year, month

and date, tap the ●right button.

f. With the display flashing P4 EdLt, tap the

◄left button to move to the end of the Program

(End will display).

Note: To disable the Daylight Saving Setting, set the beginning and

ending date to the same date.

6. Exiting the Program Mode

When the display flashes End,tap the ●right button to

exit the program mode.

7. The PIX-15 is ready for use!

Note: If you do not use Daylight Saving Time, you need to disable the Daylight

Saving Time feature. Putting the same dates in program level P3 and P4

does this. If you need assistance or have any questions, please contact us

at 1-800-253-9836.

*Note:The PIX-15 uses a Lithium battery to maintain the user settings incase of

a power failure. If a power failure occurs and the Lithium battery is dead,

the time clock settings may revert to default settings (i.e., DST Begin and

End dates may change).

Otros manuales para PIX-15

Tabla de contenidos

Otros manuales de Reloj de Amano

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano PIX-200 Manual de usuario

Amano

Amano CP-3000 Manual de usuario

Amano

Amano BX6000 Manual de usuario

Amano

Amano TS-3000i Manual de usuario

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano PIX-25 Manual de usuario

Amano

Amano EX-3500 Manual de usuario

Amano

Amano PIX-10 Manual de usuario

Amano

Amano PIX-3000x Series Guía

Amano

Amano 3500 Series Manual de usuario

Amano

Amano EX-6200 Manual de usuario

Amano

Amano EX7500 series Manual de usuario

Amano

Amano PR600 Series Manual de usuario

Amano

Amano MJR-8500 SERIES Manual de usuario

Amano

Amano PIX-15 Manual de usuario

Amano

Amano MX-300 Manual de usuario

Amano

Amano TCX-85 Manual de usuario

Amano

Amano 4700 Series Manual de usuario

Amano

Amano EX9000 series Manual de usuario

Amano

Amano BX-1600 Guía de inicio rápido

Amano

Amano TCX-22 Manual de usuario

Amano

Amano PIX-21 Manual de usuario

Amano

Amano EX9000 series Manual de usuario

Manuales populares de Reloj de otras marcas

Silicon Laboratories

Silicon Laboratories SI5324 Manual de usuario

Heathkit

Heathkit GC-1005 Manual de usuario

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manual de usuario

Andrew O'Malley

Andrew O'Malley DOTKLOK Manual de usuario

ALGE-Timing

ALGE-Timing ASC3 Manual de usuario

Bodet

Bodet Profil 960 Manual de usuario

Nixie Clock

Nixie Clock Divergence Meter Manual de usuario

La Crosse Technology

La Crosse Technology WS-8256-AL Manual de usuario

Mini Gadgets

Mini Gadgets MCPro Manual de usuario

Casio

Casio TMR-200 Manual de usuario

Progetti

Progetti ILTEMPOSTRINGE Manual

BVItech

BVItech BV-101 Manual de usuario

Progetti

Progetti KALIMERO Manual

La Crosse Technology

La Crosse Technology WT-3141b Manual

La Crosse Technology

La Crosse Technology W86531 Manual de usuario

Sharp

Sharp SPC900 Manual de usuario

La Crosse Technology

La Crosse Technology 404-50447 Manual de usuario

Datexx

Datexx DF0063 Manual de usuario