Amano PIX-55 Manual de usuario

PIX-55

Atomic Time Clock

Operation Manual

i www.amano.com •1-800-253-9836 PIX-55

Proprietary Notice

This document contains proprietary information and such information may not be

reproduced in whole or part without the written permission from Amano

Cincinnati, Inc. 140 Harrison Ave., Roseland, New Jersey 07068.

Amano Cincinnati, Inc. reserves the right to make equipment changes and

improvements, which may not be reflected in this document. Portions of this

document may have been updated to include the latest hardware or firmware

version, if applicable. We recommend that this document be read in its entirety

before any attempt is made to operate the equipment.

Thank You….

For purchasing another fine product from

Amano Cincinnati, Inc.

,Important! Do not return this clock to the retailer. If you have

any questions or need assistance, please call us toll free at

1-800-253-9836

Need Ribbons, Keys and Accessories?

Visit

www.amano.com

Or call 1-800-253-9836

Warranty Notice

Any claim for warranty, express or implied, due to the clock’s failure to properly

receive the radio signal because of interference, whatever may be the source of

this interference, are hereby expressly excluded.

For more information about the WWVB-Radio signal visit NIST’s website at:

www.boulder.nist.gov

For actual signal coverage in North America visit:

www.boulder.nist.gov/timefreq/stations/wwvbcoverage.htm

Specifications

Power Requirements

• For Clock Input: 16.5 VDC, 60Hz, 0.6A (Max.)

100 VAC ± 10%, 50/60Hz

• For AC Adapter: 120 VAC ± 10%, 60Hz

230 VAC ± 10%, 50/60Hz

• Battery: Lithium Battery for Memory Backup in case of power

failure.

Ambient Temperature: -10°C to 45°C (14°F to 113°F)

Ambient Humidity: 10% to 90% (non-condensing)

Dimensions: 6-11/16"(170 mm) Wide X 6- 7/16”(163 mm) High X

6-5/8"(168 mm) Deep.

Weight: Approximately 3.6 lbs. (1.63 kg)

Environment: Indoor use only; dust-free environment. Keep out of

direct sunlight.

2 www.amano.com •1-800-253-9836 PIX-55

External View Internal View

• The PROGRAM button is used to enter and exit the Program Mode.

• The CHANGE button is used to change the information on the display.

• The ENTER button is used to accept the information shown on the display and

save it in memory.

• The HOUR button advances the hour in the display by increments of 1.

• The MINUTE button advances the minutes in the display by increments of 1.

The LCD Display contains an Ink Capacity gauge. This gauge indicates the

amount of ink remaining in the ribbon cartridge using four bar segments, from E

(Empty) to F (Full).

The PIX-55 calculates the ink capacity of the ribbon cartridge from the number of

imprints made. As the ink capacity decreases, the bars in the gauge will

disappear. If the ribbon reaches below 25% capacity, the word “INK” will appear.

The “E”, “F” and “INK” characters will blink until the ribbon is replaced and the ink

counter is reset.

Removing the Cover & Packing Material

1.Insert the key provided and turn clockwise to unlock the cover.

2.Lift the cover to remove.

3.Remove the spacer between the Ribbon Cartridge and the Printer Carriage.

Making a Test Print

1. Make sure the PIX-55 is plugged in.

2. Insert a piece of paper or time card into the PIX-55. The clock will

automatically print YEAR, MONTH, DATE and TIME with AM or PM.

3. If the imprint is satisfactory, the PIX-55 is ready for use.

PIX-55 www.amano.com •1-800-253-9836 3

Setting the Time (If Displayed Time is Incorrect or In

Different Time Zone)

1. Unlock and remove the cover.

2. Press the HOUR advance button until the correct hour appears.

3. Press the MINUTE advance button until the correct minute appears.

Note: You must follow this procedure if you are installing the PIX-55 in a different

Time Zone from where it is currently located.

Changing the Print Style 1.Press the PROGRAM

button until dA EPI

appears.

2.Press the CHANGE

button until Prn P4

flashes in the display.

Press the ENTER

button.

3.The display will flash

the current setting.

Press the CHANGE

button until the desired

print style code

appears (see diagram).

4.When the display

flashes the correct

setting, press the

ENTER button and

press the PROGRAM

button to exit.

Changing the Print Direction

1.Press the PROGRAM button until dA EPI appears.

2.Press the CHANGE button until 0 hr P5 flashes in

the display. Press the ENTER button.

3.Press the CHANGE button until Prdr I 3 flashes in the

display. Press the ENTER button.

4.Press the CHANGE button until the correct print

direction r9h (Right Side) or LEf (Left Side) flashes

in the display, then press the ENTER button.

5.Press the PROGRAM button to exit.

4 www.amano.com •1-800-253-9836 PIX-55

Disabling Daylight Saving Time

1.Press the PROGRAM button until dA EPI appears.

2.Press the CHANGE button until dLS P3 flashes in the

display. Press the ENTER button.

3.Press the CHANGE button to turn Daylight Saving Time to

Off, then press the Enter button.

4.Press the PROGRAM button to exit

Enabling or Disabling Auto Print

1.Press the PROGRAM button until dA EPI appears.

2.Press the CHANGE button until 0 hr P5 flashes in the

display. Press the ENTER button.

3.Press the CHANGE button until A Pr I 4 flashes in the

display. Press the ENTER button.

4.Press the CHANGE button until the desired code

appears on the display, then press the Enter button.

The Auto Print codes are as follows:

Code Mode Description

P on Auto Print Will automatically print a

single print when media

is inserted.

OFF Manual

Requires you to use the

PRINT button when

printing.

P:5 on DO NOT USE

5.Press the PROGRAM button to exit.

Setting the Month and Date

1.Press the PROGRAM button until dA EPI appears, and

press the ENTER button.

2.Press the CHANGE button until the correct year appears,

then press the ENTER button.

3.Press the CHANGE button until the correct day appears,

then press the ENTER button.

4.Press the CHANGE button until the correct month

appears, then press the ENTER button.

5.When the display flashes the correct month, date and

year, press the ENTER button.

6.Press the PROGRAM button to exit.

PIX-55 www.amano.com •1-800-253-9836 5

Wall Mounting

Placement considerations:

1. Remove the Cover and remove the Back

Plate by pressing the tab.

2. Using the Back Plate as a template, mark

the lower mounting hole on the wall.

3. Mount the plate using a #10 wood screw (or

equivalent).

4. Level the Back Plate and mark the location

of the two upper mounting holes. Secure to

the wall using #10 wood screws (or

equivalent).

5. Feed the cable of AC Power Adapter

through one of the holes in the Back Plate.

6. Align the clock with the two upper tabs on

the back plate. Tilt the back of the clock

upwards to fully insert the back plate tabs

into the clock. Be careful not to pinch the

power cord with the bracket.

7. Once the tabs are inserted, tilt the clock

back down and push it against the wall. The

tabs will snap into place.

8. Replace the cover and lock it in place.

6 www.amano.com •1-800-253-9836 PIX-55

Atomic Clock Feature

The Amano atomic clock receives time signals on long

wave radio (60 kHz) from the National Institute of

Standards and Technology (NIST) operated WWVB

time signal transmitter located in Fort Collins, Colorado

and coupled with the atomic cesium clock in Boulder. It

receives the WWVB time signal via its built-in antenna

system. Your clock will try to find the signal on a daily

basis.

The Atomic Time Synchronization Indicator in the

LCD Display indicates the status of the signal. When

you first receive the clock, it may be necessary to

adjust the hour and minute. If your PIX-55 is located

in an area that cannot receive the Atomic time signal, DO NOT be concerned.

The PIX-55 will accurately keep the time using its Quartz mechanism (plus or

minus three seconds per week).

Please visit to www.boulder.nist.gov/timefreq/stations/radioclocks.htm for

more information about how radio-controlled clocks work, where they work, and

what to do when they don’t work.

Disabling the Atomic Clock

1.Press the PROGRAM button until dA EPI appears.

2.Press the CHANGE button until 0 hr P5 flashes in the

display. Press the ENTER button.

3.Press the CHANGE button until DIA9 I 8 flashes in the

display. Press the ENTER button.

4.Press the CHANGE button until Clr d 4 flashes in the

display. Press the ENTER button.

5.Press the CHANGE button to enter the last digit of the

code (3) and ENTER to accept it. The display will move

to the first digit of the code (0). Press ENTER to accept it.

When the display flashes the correct code (03), press

ENTER.

6.Press the PROGRAM button to exit.

Searching

for Signal Found

Signal

Ribbon Cartridge Replacement

1. Remove the cover.

2. Pull the two ribbon release tabs upward.

3. While holding the release tabs in an upward

position, pull the ribbon cassette out of the

cradle.

4. If the print mechanism is down and a piece of

paper cannot be inserted, unplug the clock, then

plug it back in to move the carriage up. This will

make the ribbon installation easier.

5. Insert a new ribbon underneath the printer head

as shown.

6. Turn the knob on the cassette clockwise one turn

to take up any slack in the ribbon.

7. Check the printing quality to confirm that you

have installed the ribbon properly.

8. Reset the INK capacity gauge by pressing the

CHANGE and ENTER buttons at the same time

9. Replace the cover.

Error Messages

Error Code Cause

Pr E I Home sensor, motor carriage stuck

Pr E 2 Timing sensor, carriage stuck

Pr E 3 Home sensor

Pr E 4 Carriage stuck

Pr E r General print error

dL Daylight Saving Time Program

For error messages Pr E I through Pr E r, unplug the clock before checking to

see that the carriage is not stuck or jammed. Also, check to see that the ribbon

cables are in good condition. After clearing any jams, unplug the clock, then plug

it back in. Contact us at 1-800-253-9836 if you need assistance.

The dL error message signifies that an attempt was made to get into the

Program mode during the Daylight Saving changeover one-hour lockout. Wait

one hour and you will be able to program the clock.

Cleaning

Do not use any chemical solvents or oils to clean or lubricate your PIX-

55. This will damage your clock.

To clean the inside of your clock, blow it out with air.

Otros manuales para PIX-55

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Reloj de Amano

Amano

Amano PIX-21 Manual de usuario

Amano

Amano EX9000 series Manual de usuario

Amano

Amano Time Partner TCX-11 Manual de usuario

Amano

Amano BX-1600 Guía de inicio rápido

Amano

Amano CP-5000 Manual de usuario

Amano

Amano PIX-10 Manual de usuario

Amano

Amano 4700 Series Manual de usuario

Amano

Amano PIX-10 Manual de usuario

Amano

Amano PIX-200 Manual de usuario

Amano

Amano EX-3500 Manual de usuario

Amano

Amano MRX-35 Manual de instrucciones

Amano

Amano TS-3000i Manual de usuario

Amano

Amano BX-1500 Manual de usuario

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano MJR-8000 Series Instrucciones de montaje

Amano

Amano PR600 Series Manual de usuario

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano BX6000 Manual de usuario

Amano

Amano MJR-8500 SERIES Manual de usuario

Amano

Amano CP-3000 Manual de usuario

Amano

Amano PIX-55 Manual de usuario

Amano

Amano TCX-85 Manual de usuario

Amano

Amano PIX-25 Manual de usuario

Amano

Amano MJR-8000 Series Guía de solución de problemas

Manuales populares de Reloj de otras marcas

Silicon Laboratories

Silicon Laboratories SI5324 Manual de usuario

Heathkit

Heathkit GC-1005 Manual de usuario

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manual de usuario

Andrew O'Malley

Andrew O'Malley DOTKLOK Manual de usuario

ALGE-Timing

ALGE-Timing ASC3 Manual de usuario

Bodet

Bodet Profil 960 Manual de usuario

Nixie Clock

Nixie Clock Divergence Meter Manual de usuario

La Crosse Technology

La Crosse Technology WS-8256-AL Manual de usuario

Mini Gadgets

Mini Gadgets MCPro Manual de usuario

Casio

Casio TMR-200 Manual de usuario

Progetti

Progetti ILTEMPOSTRINGE Manual

BVItech

BVItech BV-101 Manual de usuario

Progetti

Progetti KALIMERO Manual

La Crosse Technology

La Crosse Technology WT-3141b Manual

La Crosse Technology

La Crosse Technology W86531 Manual de usuario

Sharp

Sharp SPC900 Manual de usuario

La Crosse Technology

La Crosse Technology 404-50447 Manual de usuario

Datexx

Datexx DF0063 Manual de usuario