Amano PIX-15 Manual de usuario

User’s Guide

PIX-15

Electronic Time Recorder

Thank you…

for purchasing another fine product from

Amano Cincinnati, Inc.

IMPORTANT

The Daylight Saving Time date settings have been preset.

DO NOT change the Daylight Saving Time date settings unless you

live in Arizona, Hawaii, parts of Indiana, or any other area that does

not use Daylight Saving Time. Do not return this clock to the

retailer. If you have any questions or need assistance,

please call us toll free

1-800-253-9836

Proprietary Notice

This document contains proprietary information and such information may

not be reproduced in whole or part without the written permission from

Amano Cincinnati, Inc. 140 Harrison Ave., Roseland, New Jersey 07068.

Amano Cincinnati, Inc. reserves the right to make equipment changes and

improvements which may not be reflected in this document.

We recommend that this document be read in its entirety before any attempt is

made to operate the equipment.

Visit us on the web at:

http://www.amano.com

Your PIX-15

Removing the Cover & Packing Materials

Please Note:

You must remove the packaging spacers from the printer block and the

Printer Carriage before attempting to use your PIX-15.

1. Lift the printer block and

remove the spacer.

Amano Cincinnati, Inc. (Mon. - Fri. 8:00 - 5:00 PST) 1-800-253-9836

Page 1

2. Insert the key provided

and turn clockwise to

open the case. Lift the

cover to remove.

3. Remove the spacer

between the Ribbon

Cartridge and the Printer

Carriage.

4. Re-install the cover. Your

PIX-15 is ready for use!

1-800-253-9836 (Mon. - Fri. 8:00 - 5:00 PST) Amano Cincinnati, Inc.

Page 2

Before You Change Any Settings

Take a moment to familiarize yourself with the items explained below.

The Front Panel

Normally, the Display Window shows the date and time. When you use

the Quick Set or Program Mode to change the settings of the PIX-15,

the instructions to change the clock are shown in this window.

The two buttons on the front panel are used to navigate through the

Quick Set and Program Mode to change the clock’s settings.

The left button is marked with a Wsymbol. It is called the

CHANGE Button. Use this button to change the information shown on

the display when you are in the Quick Set or Program Mode.

The right button is marked with a zsymbol. It is called the

ENTER Button. When you are in the Quick Set or Program Mode,

use this button to enter the setting shown on the display into memory.

The Reset Button

The RESET Button (which is

shaped like a post) is located on

the bottom of the clock.

Please Note:

You do not need the key to set the time or to program the clock!!

You do need the key to change the ribbon or mount the clock on the

wall (See page 7).

If you have any questions, please call 1-800-253-9836.

Amano Cincinnati, Inc. (Mon. - Fri. 8:00 - 5:00 PST) 1-800-253-9836

Page 3

Make a Test Print

1. Plug in the power cord.

2. Insert a piece of paper or time card into the PIX-15. The clock will

automatically print YEAR, MONTH, DATE and TIME with AM or PM

(in Pacific Time).

Note: The PIX-15 will automatically adjust for Daylight Saving Time.

3. If the imprint is satisfactory, and you are going to place the PIX-15 on

a desk, table, or shelf, the PIX-15 is ready to be used.

4. In order for you to set the time or change the print style, you must

enter a code. Choose a code from the list below that best fits your

needs. Continue to the next page for instructions on how to enter

your code.

Code Print Style Print Direction

6510 DAY, 12H, 60th Right Side Printing

6210 DAY, 24H, 10th Right Side Printing

6810 DAY, 24H, 100th Right Side Printing

6520 DATE, 12H, 60th Right Side Printing

6620 DATE, 24H, 60th Right Side Printing

6820 DATE, 24H, 100th Right Side Printing

6530 MONTH, DATE, 12H, 60th Right Side Printing

6630 MONTH, DATE, 24H, 60th Right Side Printing

6830 MONTH, DATE, 24H, 100th Right Side Printing

6570 YEAR, MONTH, DATE, 12H, 60th Right Side Printing

6071 YEAR, MONTH, DATE, RCV’D Right Side Printing

6072 YEAR, MONTH, DATE, SENT Right Side Printing

6073 YEAR, MONTH, DATE, FAX’D Right Side Printing

6074 YEAR, MONTH, DATE, VOID Right Side Printing

6075 YEAR, MONTH, DATE, PAID Right Side Printing

6076 YEAR, MONTH, DATE, CFM’D Right Side Printing

6077 YEAR, MONTH, DATE, APR’D Right Side Printing

6078 YEAR, MONTH, DATE, CMPL’D Right Side Printing

6079 YEAR, MONTH, DATE, ORIGN Right Side Printing

6070 YEAR, MONTH, DATE, FILE Right Side Printing

Note: If you cannot locate the desired print style from the above list,

please contact us at 1-800-253-9836 for assistance.

1-800-253-9836 (Mon. - Fri. 8:00 - 5:00 PST) Amano Cincinnati, Inc.

Page 4

Entering the Clock Program

The following steps describe how to get into the clock program. To set

the print style and time, use a code chosen from the list.

1. To Enter the Code

a. Press and hold the RESET button on the bottom of the

clock. (Refer to Page 3 for location.)

b. While holding down the RESET button, press and hold

the zright button on the front panel.

c. While holding the zright button, release the RESET

button.

d. When Pro9 flashes in the display,

release the zright button.

e. Tap the zright button again. The

display will show 0000.

f. Tap the Wleft button until the first

number of your code appears, then

tap the zright button.

g. Tap the Wleft button until the second

number of your code appears, then

tap the zright button.

h. Tap the Wleft button until the third

number of your code appears, then

tap the zright button.

i. Tap the Wleft button until the fourth

number of your code appears, then

tap the zright button.

j. When the display flashes all four digits,

tap the zright button again.

k. When the display flashes Pl ddA E, tap

the Wleft button.

Amano Cincinnati, Inc. (Mon. - Fri. 8:00 - 5:00 PST) 1-800-253-9836

Page 5

2. Set the Time

When setting the time you must use 24 hour format (i.e.

13:00 = 1:00 pm). This will NOT make the clock print

military time, it simply tells the clock am from pm.

a. When the display flashes P2 CCLoc, tap

the zright button.

b. The small “12” will flash. Tap the

zright button again.

c. The hour digits will flash. Tap the

Wleft button until the correct hour

appears. Remember to use a 24 hour

format (2:00 pm = 14:00). Then tap the

zright button.

d. The minutes digits will flash. Tap the

Wleft button until the correct minutes

appear, then tap the zright button twice.

e. When the display flashes P2 CCLoc, tap the

Wleft button until you see End, then

tap the zright button.

3. The PIX-15 is ready for use!

Note: If you do not use Daylight Saving Time, you need to disable

the Daylight Saving Time feature. Putting the same dates in program

level P3 and P4 does this. If you need assistance or have any

questions, please contact us at 1-800-253-9836.

1-800-253-9836 (Mon. - Fri. 8:00 - 5:00 PST) Amano Cincinnati, Inc.

Page 6

Amano Cincinnati, Inc. (Mon. - Fri. 8:00 - 5:00 PST) 1-800-253-9836

Page 7

Replacing the Ribbon

1. Insert the key into the key hole (see page 2

for keyhole location) and turn the key.

2. Grab the cover on both sides and lift to

remove it.

3. Pull the two catches (B) upward and hold

them with your index and middle fingers.

Remove the ribbon cassette.

Note:If the print mechanism is in the down position and a piece

of paper cannot be inserted, press the RESET button to move the

carriage up. This will make the ribbon installation easier.

4. Insert a new ribbon between the ribbon guide (C) and the printer

head (D).

5. Turn the knob on the cassette clockwise one turn to take up any

slack in the ribbon.

6. To replace the cover, remove the key, align the lower back corners

to the base of the clock and snap the cover down into position.

Mounting the Clock

1. Remove the cover as per the instructions above.

2. With the clock facing you, remove the mounting bracket by pulling

the top tabs (A) towards you, and then pushing the tabs down

(see below).

3. Securely mount the PIX mounting bracket on the wall using three

#10 wood screws or equivalent.

4. Place the PIX-15 on the Mounting Bracket by sliding the top tabs

into the slots on each side of the case. Push the PIX-15 back and

down against the Mounting Bracket until the PIX-15 snaps into

place. Be careful not to pinch the power cord with the bracket.

Installing the cover will secure the PIX-15 to the mounting bracket.

Error Messages

Possible Error Messages:

If any of these messages appear on the display, unplug the clock from

your outlet then plug it back in again. If the message still appears on

your display, please contact us at 1-800-253-9836 for assistance.

CAUTION:

Do not use any chemical solvents or oils to clean or lubricate your

PIX-15. This will damage your clock. To clean the inside of your clock,

blow it out with air.

Specifications

Power Requirements: For PIX-15 Input: AC16.5V, 60Hz, 0.6A (Max.)

For AC Adapter: AC120V ± 10%, 60Hz

AC230V ± 10%, 50Hz

AC240V ± 10%, 50Hz

Ambient Temperature: -10°C to 45°C (14°F to 113°F)

Ambient Humidity: 10% to 90% (no condensation)

Dimensions: 140mm (W) x 150mm (H) x 165mm (D)

(5½” x 6” x 6½”)

Weight: 1.8Kg (4.2 lbs.)

Environment: Indoor use only; dust-free environment

Keep out of direct sunlight

For PIX-15 with 120V AC Adapter:

Listed and Certified by Underwriters Laboratories, Inc.

Page 8

1-800-253-9836 (Mon. - Fri. 8:00 - 5:00 PST) Amano Cincinnati, Inc.

Otros manuales para PIX-15

Tabla de contenidos

Otros manuales de Reloj de Amano

Amano

Amano PIX-28 Manual de usuario

Amano

Amano PIX-10 Manual de usuario

Amano

Amano MJR-8000 Series Instrucciones de montaje

Amano

Amano PIX-75 Manual de usuario

Amano

Amano PIX-10 Manual de usuario

Amano

Amano PIX-10 Manual de usuario

Amano

Amano BX 2000 Manual de usuario

Amano

Amano PR600 Series Manual de usuario

Amano

Amano EX3000N Manual de usuario

Amano

Amano Amano TCX 21 Manual de usuario

Amano

Amano PIX-21 Manual de usuario

Amano

Amano MICRODER MR-7000 Series Manual de usuario

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano EX9000 series Manual de usuario

Amano

Amano 4700 Series Manual de usuario

Amano

Amano MJR-8500 SERIES Manual de usuario

Amano

Amano PIX-3000x Series Guía

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano EX7500 series Manual de usuario

Amano

Amano PIX-3000x Series Manual de usuario

Amano

Amano PIX-55 Manual de usuario

Amano

Amano TCX-22 Manual de usuario

Amano

Amano PIX-25 Instrucciones de funcionamiento

Amano

Amano PIX-55 Manual de usuario

Manuales populares de Reloj de otras marcas

Silicon Laboratories

Silicon Laboratories SI5324 Manual de usuario

Heathkit

Heathkit GC-1005 Manual de usuario

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manual de usuario

Andrew O'Malley

Andrew O'Malley DOTKLOK Manual de usuario

ALGE-Timing

ALGE-Timing ASC3 Manual de usuario

Bodet

Bodet Profil 960 Manual de usuario

Nixie Clock

Nixie Clock Divergence Meter Manual de usuario

La Crosse Technology

La Crosse Technology WS-8256-AL Manual de usuario

Mini Gadgets

Mini Gadgets MCPro Manual de usuario

Casio

Casio TMR-200 Manual de usuario

Progetti

Progetti ILTEMPOSTRINGE Manual

BVItech

BVItech BV-101 Manual de usuario

Progetti

Progetti KALIMERO Manual

La Crosse Technology

La Crosse Technology WT-3141b Manual

La Crosse Technology

La Crosse Technology W86531 Manual de usuario

Sharp

Sharp SPC900 Manual de usuario

La Crosse Technology

La Crosse Technology 404-50447 Manual de usuario

Datexx

Datexx DF0063 Manual de usuario