ALPA AA082 Manual de usuario
Lingua originale: inglese REV. 2 - 08/22
metrology
ALPA_CALIPER_IP66
1. MM/IN button
2. ABS button
3. REL button
4. Battery Cover
5. Display
6. Fastening Screw
DESCRIPTION
2 3 41
65
EN
TECH DATA
Measuring range 0 - 300 mm | 0 - 500 mm | 0 - 600 mm | 0 - 1000 mm
Resolution 0.01 mm
Water Protection Level IP66
Power 3V (CR2032) Lithium button cell
Measuring speed < 1.5 m/s
Storage temperature -10°C / + 60°C
Working temperature +5 / + 40°C
ALPA_CALIPER_IP66
FUNCTION
OPERATIONS
Zero-setting at any position for incremental measurement.
mm/in conversion at any position.
Switch of absolute measurement and incremental measurement at any point.
Preparation
1. Dry the surface of the protective sticker (pls see Notes) and clean the measuring surfaces.
2. Loosen the locking screw and move the slider to check if the LCD display and all the buttons
work properly.
MEASUREMENT
EN
1. Press REL button to switch on power and then LCD displays “REL” as prompt sign.
2. Press mm/inch button to select the desired unit system.
3. Move the slider to make two outside measuring faces touch gently and press REL button to set
Zero. Then it can take measurement.
ALPA_CALIPER_IP66
REL BUTTON - For switch-on power, switch-off power, zero-clearing and presetting
Press REL button shortly to switch on power when power is off. It’ll clear zero by pressing ZERO key
shortly at non-setting mode. Meanwhile, turn measuring mode to incremental mode. It will increase
current digit whose bit has been changed by for example pressing shortly ZERO key in setting mode.
If it’s over maximum value for this bit, just put digit back to 0. Press REL button for long to switch off
power after measurement is over.
EN
ABS BUTTON - For switch of absolute measurement and incremental measurement
A digital caliper is not in setting mode when it’s switched on. Press ABS key shortly in this mode to
set value to one preset value which has been set (if preset value is invalid, one should set preset
value to be 0), meanwhile, one should turn measuring mode to absolute mode and LCD displays
ABS as prompt sign. Keep pressing ABS key in this mode to enter preset mode. LCD displays SET
as prompt sign and select current bit to be at highest bit. The current digit which corresponds to the
changed bit ashes.
It’ll set current changed bit to the right by one bit by pressing ABS key shortly in setting mode. If
it’s over the lowest bit, it goes back to the highest bit; it’ll take current changed value by keeping
pressing ABS key at this mode. Then it gets out of setting mode and enters absolute measurement
automatically (and cancel all special functions). LCD displays ABS as prompt sign and displays
preset value which has been set.
ALPA_CALIPER_IP66
BRIEF ON MAINTENANCE
1. Erratic display (ashing digits) shows dead battery. Please replace the battery.
2. No displace shows poor contact of a battery or short-circuit of both poles of the battery. Please
check and adjust pole akes and battery insulator cover.
3. In case water enters the battery cover, open the cover I & II immediately, take out the battery
and blow the inside of the battery cover at a temperature less than 40°C till it gets dry.
MAINTENANCE
Never apply voltage (e.g. engraving with an electric pen) on any
part of the Digital Caliper for fear of damaging the circuit.
Please take out the battery when IP66 digital caliper is not in use
for a long time.
Do not get near the magnetic eld.
Disassembly is not permitted except for the battery cover.
1 x lithium battery 3V type CR2032
BATTERY CHANGE
EN
ALPA_CALIPER_IP66
DESCRIZIONE
1. Tasto MM/IN
2. Tasto ABS
3. Tasto REL
4. Alloggio batteria
5. Display
6. Vite di ssaggio
23 41
65
Tabla de contenidos
Idiomas:
Otros manuales de Instrumento de medición de ALPA
ALPA
ALPA MEGArod Manual de usuario
ALPA
ALPA AA052 Manual de usuario
ALPA
ALPA AA021 Manual de usuario
ALPA
ALPA Exacto BA027 Manual de usuario
ALPA
ALPA ABSolutus Manual de usuario
ALPA
ALPA MEGAline AA084 Manual de usuario
ALPA
ALPA 5 Functions Manual de usuario
ALPA
ALPA PICKall Manual de usuario
ALPA
ALPA Exacto BA070 Manual de usuario
ALPA
ALPA LITEsurf Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario