Alliance Laundry Systems H236I Manual del propietario

Installation and Operation

H236I

OPERATING INSTRUCTIO

Select Wash Temperature

Select Fabric Type

Load Supply Dispenser (See

Insert Coin(s) / Card.

Open Dispenser

Compartment (as

Close Dispenser

Detergent

DISPENSER INSTRUCTION

685942

685557

NOTA: El manual en español aparece después del manual en inglés.

Front Load

Washers

Metered Commercial

Part No. 685945R5

October 1999

685945 1

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the washer changes ownership,

be sure this manual accompanies the washer.)

without the expressed written consent of the publisher.

For your safety and to reduce the risk of

fire or an explosion, do not store or use

gasoline or other flammable vapors and

liquids in the vicinity of this or any other

appliance.

WARNING

2685945

Replacement Parts . . .

If replacement parts are required, contact the source from

where you purchased your washer, or contact: Alliance Laundry Systems LLC

Shepard Street

P.O. Box 990

Ripon, WI 54971-0990

Phone: (920) 748-3950

for the name and address of the nearest authorized parts

distributor.

Table of

Contents

Replacement Parts ...............................................................................2

Important Safety Instructions .............................................................3

Dimensions and Specifications.............................................................5

Additional Security...............................................................................5

Coin Slide Guards.................................................................................5

Washer Slide Extension .......................................................................6

Before You Start....................................................................................7

Installing the Washer

Step 1: Position Washer Near Installation Area..................................7

Step 2: Connect Water Inlet Hoses.....................................................8

Step 3: Connect Drain Hose to Drain Receptacle...............................9

Step 4: Remove the Shock Sleeves and Shipping Brace ..................10

Step 5: Position and Level the Washer .............................................10

Step 6: Wipe Out Inside of Wash Drum...........................................11

Step 7: Plug in the Washer................................................................11

Step 8: Check Installation.................................................................11

Moving Washer to a New Location ..................................................12

Electrical Requirements ....................................................................13

Water Supply Requirements..............................................................14

Operation Instructions for Electromechanical Washers

Step 1: Load Laundry........................................................................15

Step 2: Close Loading Door..............................................................15

Step 3: Add Laundry Supplies..........................................................15

Step 4: Set WASH/RINSE Temperatures.........................................16

Step 5: Select Fabric Selector ...........................................................16

Step 6: Insert Money.........................................................................16

Indicator Lights.................................................................................16

Operation Instructions for Electronic Control Washers

Step 1: Load Laundry........................................................................17

Step 2: Close Loading Door..............................................................17

Step 3: Add Laundry Supplies..........................................................17

Step 4: Set Fabric Selector................................................................18

Step 5: Set Wash Temperature..........................................................18

Step 6: Insert Coin(s) or Card...........................................................18

Step 7: Start Washer..........................................................................18

Indicator Lights.................................................................................19

Maintenance

Cold Weather Care ...........................................................................20

Care of Your Washer .......................................................................20

Vacations and Extended Non-Use ....................................................20

Before You Call For Service ..............................................................21

Information for Handy Reference ....................................................22

Installer Checklist ...............................................................Back Cover

685945 3

IMPORTANT SAFETY INSTRUCTIONS

(SAVE THESE INSTRUCTIONS)

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS

in the INSTALLATION manual for the proper

grounding of the washer.

3. Do not wash articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

flammable or explosive substances as they give

off vapors that could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the

wash water. These substances give off vapors

that could ignite or explode.

5. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not

been used for two weeks or more. HYDROGEN

GAS IS EXPLOSIVE. If the hot water system

has not been used for such a period, before

using a washing machine or combination

washer-dryer, turn on all hot water faucets and

let the water flow from each for several

minutes. This will release any accumulated

hydrogen gas. The gas is flammable, do not

smoke or use an open flame during this time.

6. Do not allow children to play on or in the

washer. Close supervision of children is

necessary when the washer is used near

children. This is a safety rule for all appliances.

7. Before the washer is removed from service or

discarded, remove the door to the washing

compartment.

8. Do not reach into the washer if the wash drum

is moving.

9. Do not install or store the washer where it will

be exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer,

or attempt any servicing unless specifically

recommended in the user-maintenance

instructions or in published user-repair

instructions that you understand and have the

skills to carry out.

12. To reduce the risk of an electric shock or fire,

DO NOT use an extension cord or an adapter

to connect the washer to the electrical power

source.

13. Use your washer only for its intended purpose,

washing clothes.

14. ALWAYS disconnect the washer from

electrical supply before attempting any service.

Disconnect the power cord by grasping the

plug, not the cord.

15. Install the washer according to the

INSTALLATION INSTRUCTIONS. All

connections for water, drain, electrical power

and grounding must comply with local codes

and be made by licensed personnel when

required. Do not do it yourself unless you know

how!

16. To reduce the risk of fire, clothes which have

traces of any flammable substances such as

vegetable oil, cooking oil, machine oil,

flammable chemicals, thinner, etc. or anything

containing wax or chemicals such as in mops

and cleaning cloths, must not be put into the

washer.Theseflammablesubstancesmay cause

the fabric to catch on fire by itself.

17. Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

18. Keep your washer in good condition. Bumping

or dropping the washer can damage safety

features. If this occurs, have your washer

checked by a qualified service person.

19. If the supply cord is damaged, it must be

replaced by a special cord or assembly

available from the manufacturer or its service

agent.

20. Be sure water connections have a shut-off valve

and that fill hose connections are tight. CLOSE

the shut-off valves at the end of each wash day.

To reduce the risk of fire, electric shock,

serious injury or death to persons when

using your washer, follow these basic

precautions: W023E

WARNING

(continued)

4685945

21. Loading door MUST BE CLOSED any time

the washer is to fill, tumble or spin. DO NOT

by-pass the loading door switch by permitting

the washer to operate with the loading door

open.

22. Always read and follow manufacturer’s

instructions on packages of laundry and

cleaning aids. Heed all warnings or

precautions. To reduce the risk of poisoning or

chemical burns, keep them out of the reach of

children at all times (preferably in a locked

cabinet).

23. Always follow the fabric care instructions

supplied by the garment manufacturer.

24. Never operate the washer with any guards

and/or panels removed.

25. DO NOT operate the washer with missing or

broken parts.

26. DO NOT by-pass any safety devices.

27. Failure to install, maintain, and/or operate this

washer according to the manufacturer's

instructions may result in conditions which can

produce bodily injury and/or property damage.

NOTE:TheWARNINGandIMPORTANTSAFETY

INSTRUCTIONS appearing in this manual are not

meant to cover all possible conditions and situations

that may occur. Common sense, caution and care

must be exercised when installing, maintaining, or

operating the washer.

Always contact your dealer, distributor, service agent or

the manufacturer about any problems or conditions you

do not understand.

685945 5

Dimensions and Specifications . . .

Additional Security . . .

Torx security screws are available (as optional equipment

at extra cost) for securing lower access panel to washer.

Order part number 62853.

A Torx bit, part number 282P4, is available (as optional

equipment at extra cost) for installing the Torx security

screws.

A Torx bit holder, part number 24161, is available (as

optional equipment at extra cost) to be used with the Torx

bit.

Coin Slide Guards . . .

(Coin Slide Models Only)

Using serrated hex head screws from accessories bag,

install coin slide guard to front of control cabinet. See

illustration.

A special security screw kit is available (as optional

equipment at extra cost) for securing the coin slide guard

and front panel to front of washer. Order Security Kit

No. 298P3. A special driver, part number 56217, is

available (as optional equipment at extra cost) for

installing the special security screws.

NOTE: Coin slides and coin drawers are shown for

illustration only. You must obtain them locally.

26.9" (68.3 cm)

28" (71.1 cm)

43" (109.2 cm)

29.6" (75.1 cm)

(5.1 cm)

31.1" (79 cm)

14.3"

(36.3 cm)

17.5"

(44.8 cm)

H270IE3a

OPERATING INSTRUCTIONS

Select Wash Temperature

HOT, WARM, COLD.

Select Fabric Type

NORMAL, PERM PRESS, DELICATE.

Load Supply Dispenser (See Instructions Below).

Load Clothes.

Insert Coin(s) / Card.

To Start Washer-Close Door and Push Start.

Open Dispenser Door.

Load Supplies in Proper

Compartment (as Indicated).

Close Dispenser Door.

Detergent

Liquid Bleach

Fabric Softener

DISPENSER INSTRUCTIONS

PERMANENT PRESS ALL FABRIC

685942

H174I

685557

6685945

Washer Slide Extension . . .

(Coin Slide Models Only)

Remove slide extension, shoulder screw, plastic boot,

actuator, actuator support, screws and lockwashers from

the accessories bag. Install slide extension as follows:

1. Unlock and open service door. Remove locking rod

holding coin slide to front of security cabinet.

NOTE: Refer to following illustration for Steps 2

through 4.

2. Assemble plastic boot (No. 36165) onto actuator

support (No. 685592).

3. Assemble actuator (No. 36164) to actuator support

(No. 685592) using shoulder screw (No. 36166).

4. Place actuator and support assembly onto slide

extension, and install screw and lockwasher (No.

03950).

5. Install assembed slide extension through coin slide

opening of security cabinet by reaching through

service door opening.

6. Assemble slide extension (No. 685593) to top side

of coin slide using two screws and lockwashers

(No. 03950), and tighten firmly. See illustration

below.

7. Reinstall assembled coin slide in security cabinet.

Close and lock service door.

After slide extension has been installed, check washer

operation as follows:

1. Connect electrical power to washer.

NOTE: To determine if slide functions properly,

allow washer to complete its cycle, and for timer to

stop, before starting evaluation process.

2. Place required number of coins in slide. Push slide in

slowly and listen for coins to drop into coin drawer.

3. Push slide in a little farther and observe through

service door opening that actuator drops beyond

timer clutch. Continue pushing slide all the way in

and pull back. Confirm that the actuator will rotate

timer clutch and wash cycle starts.

NOTE: Washer will not start until Push-to-Start has

been pressed.

To reduce the risk of electric shock, fire,

explosion, serious injury or death:

• Disconnect electric power to the washer

before servicing.

• Never start the washer with any guards/

panels removed.

• Whenever ground wires are removed

during servicing, these ground wires must

be reconnected to ensure that the washer

is properly grounded. W003

WARNING

H067I

H068I

685945 7

Before You Start . . .

Tools

For most installations, the basic tools you will need are:

Electrical Requirements

Refer to serial plate for specific electrical requirements.

For more detailed information, refer to section on

Electrical Requirements.

Water Supply Requirements

Washer needs two standard 3/4 inch (19.1 mm) water

supply faucets with a pressure between 20-120 pounds

per square inch (138 to 827 kPa). For more detailed

information, refer to section on Water Supply

Requirements.

Installing the Washer . . .

Step 1:

Position Washer Near Installation

Area

Move washer so that it is within four feet of the desired

area of installation.

D074IE1H

LEVEL

SCREWDRIVER

PLIERS

WRENCH

SOCKET

WRENCH

H054IE1A

8685945

Step 2:

Connect Water Inlet Hoses

NOTE: Refer to section on Water Supply

Requirements before connecting water inlet hoses.

Remove the four plain rubber washers from accessories

bag, and install them according to the illustration.

Turn on the water supply faucets and flush the lines for

approximately two minutes to remove any foreign

materials that could clog the screens in the water mixing

valve.

NOTE: When installing in newly constructed or

renovated building, it is very important to flush the

lines since build-up may have occurred during

construction.

IMPORTANT: Thread hose couplings onto valve

connections finger-tight, then approximately 1/4 turn

with pliers. DO NOT cross thread or overtighten

couplings.

Turn water on and check for leaks. If leaks are found,

retighten the hose couplings. Continue tightening and

rechecking until no leaks are found.

RUBBER WASHER

(Plain)

H091IE1A

INSTALL THIS

END OF HOSE

TO WATER

SUPPLY FAUCET

INSTALL THIS END OF HOSE

TO VALVE CONNECTIONS

AT REAR OF WASHER

INLET

HOSE

RUBBER WASHER

(Plain)

H100IE1A

COLD WATER

CONNECTION

HOT WATER

CONNECTION

WATER SUPPLY

FAUCETS

WATER INLET

HOSES

Tabla de contenidos

Idiomas:

Otros manuales de Arandela de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CCN020HNF Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HD60 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWS04M Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems UW35PV Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems LWS02M series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Metered models Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HWTB21 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems LWS01A* series Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems DWA021*A Instrucciones de montaje

Alliance Laundry Systems

Alliance Laundry Systems A Series Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems D1528ENR3 Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems AFNE9BSP113TN01 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HF455 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen LFNE5B Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems WFF100 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems AWC39323059 Instrucciones de montaje

Alliance Laundry Systems

Alliance Laundry Systems FLW1527C Guía

Alliance Laundry Systems

Alliance Laundry Systems UM202 Series Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems SF18VNV Guía de mantenimiento y servicio

Alliance Laundry Systems

Alliance Laundry Systems FTS90A*N Instrucciones de montaje

Alliance Laundry Systems

Alliance Laundry Systems HWF261*E Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CHM1772C Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems NX18BVPA6 Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario