Alliance Laundry Systems CP040PMN1 Manual de usuario

Programming

www.comlaundry.com

Washer-Extractors

Pocket Hardmount Variable-Speed

PS40 Control

Refer to Page 9 for Model Identification

PHM1398C

1 2 3

4 5 6

7 8 9

PS40

PROG

RUN

PHM1398C

Part No. F8112301R1

December 2007

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

means without the expressed written consent of the publisher.

F8112301 1

Table of

Contents

Safety Information.............................................................................. 3

Explanation of Safety Messages........................................................... 3

Important Safety Instructions ............................................................... 3

Safety Decals ........................................................................................ 5

Operator Safety..................................................................................... 6

Safe Operating Environment ................................................................ 6

Environmental Conditions ............................................................... 6

Machine Location ............................................................................ 7

Input and Output Services................................................................ 7

DirectDrive ...................................................................................... 8

Model Identification ............................................................................ 9

Introduction......................................................................................... 10

Nameplate Location.............................................................................. 10

Replacement Parts ................................................................................ 10

Customer Service.................................................................................. 10

Control Identification......................................................................... 11

Start-up................................................................................................ 12

Setup (Pre-Program) Mode .............................................................. 12

Test Mode ........................................................................................ 16

Test 1: Inputs.................................................................................... 16

Test 2: Analog Reference................................................................. 17

Test 3: Not Available ....................................................................... 17

Test 4: Water Level Control Test..................................................... 17

Test 5: Temperature Sensor Test ..................................................... 17

Test 6: Test of Outputs..................................................................... 18

Test 7: Keyboard Test...................................................................... 18

Ram Reset ........................................................................................ 18

Programming ...................................................................................... 19

Overview Of Modes ............................................................................. 19

Operating Mode .................................................................................... 20

Select and Run a Program................................................................ 20

Program Progress Indicators ............................................................ 20

Program Start Delay......................................................................... 20

Changing To Another Program........................................................ 20

Temporary Program Alteration........................................................ 20

Temperature and RPM Display ....................................................... 20

Rapid Advance................................................................................. 20

Programmed Stop............................................................................. 21

Stopping a Program.......................................................................... 21

Manually Adding Water .................................................................. 21

Manually Draining ........................................................................... 21

Manual Heating................................................................................ 22

Manually Activating the Chemical Supply Signals ......................... 22

Display Total Operating Hours........................................................ 22

Program Memory Inventory ............................................................ 22

2F8112301

Programming Mode .............................................................................. 22

Creating a Program .......................................................................... 22

Inserting/Deleting a Program Step................................................... 27

Copy Mode ........................................................................................... 28

PS40 Water Level Sensor Calibration Procedure ............................ 28

PS40 Diagnostics .................................................................................. 29

Alarm Codes .................................................................................... 29

Fault Codes ...................................................................................... 29

Programming Tips ................................................................................ 30

Standard Programs ............................................................................ 31

Program 0 – Rinse and Spin ................................................................. 32

Program 1 – Cold Wash........................................................................ 34

Program 2 – Warm Wash ..................................................................... 36

Program 3 – Hot Wash ......................................................................... 38

Program 4 – Perm Press........................................................................ 40

Program 5 – Cold Gentle ...................................................................... 42

Program 6 – Warm Gentle.................................................................... 44

Program 7– Rubber Mats...................................................................... 46

Program 8 – Soak.................................................................................. 48

Program 9 – Starch ............................................................................... 50

Program Worksheet .............................................................................. 52

F8112301

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,”

and “CAUTION”), followed by specific instructions,

are found in this manual and on machine decals. These

precautions are intended for the personal safety of the

operator, user, servicer, and those maintaining the

machine.

Additional precautionary statements (“IMPORTANT”

and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used

to inform the reader of specific procedures where

minor machine damage will occur if the procedure

is not followed.

NOTE: The word “NOTE” is used to communicate

installation, operation, maintenance or servicing

information that is important but not hazard

related.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS in

the INSTALLATION manual for the proper

grounding of the washer.

3. Do not wash textiles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, kerosene, waxes, cooking oils, dry-

cleaning solvents, or other flammable or

explosive substances as they give off vapors that

could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the

wash water. These substances give off vapors that

could ignite or explode.

5. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS

IS EXPLOSIVE. If the hot water system has not

been used for such a period, before using a

washing machine or combination washer-dryer,

turn on all hot water faucets and let the water

flow from each for several minutes. This will

release any accumulated hydrogen gas. The gas is

flammable, do not smoke or use an open flame

during this time.

6. Do not allow children to play on or in the washer.

Close supervision of children is necessary when

the washer is used near children. This is a safety

rule for all appliances.

7. Before the washer is removed from service or

discarded, remove the door to the washing

compartment.

8. Do not reach into the washer if the wash drum is

moving.

DANGER indicates the presence of a

hazard that will cause severe personal

injury, death, or substantial property

damage if the danger is ignored.

DANGER

WARNING indicates the presence of a

hazard that can cause severe personal

injury, death, or substantial property

damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a

hazard that will or can cause minor

personal injury or property damage if the

caution is ignored.

CAUTION

To reduce the risk of fire, electric shock,

serious injury or death to persons when

using your washer, follow these basic

precautions:

W023

WARNING

Safety Information

F8112301

9. Do not install or store the washer where it will be

exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or

attempt any servicing unless specifically

recommended in the user-maintenance

instructions or in published user-repair

instructions that the user understands and has the

skills to carry out.

12. To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to

connect the washer to the electrical power source.

13. Use washer only for its intended purpose,

washing textiles.

14. Never wash machine parts or automotive parts in

the machine. This could result in serious damage

to the basket.

15. ALWAYS disconnect the washer from electrical

supply before attempting any service. Disconnect

the power cord by grasping the plug, not the cord.

16. Install the washer according to the

INSTALLATION INSTRUCTIONS. All

connections for water, drain, electrical power and

grounding must comply with local codes and be

made by licensed personnel when required.

17. To reduce the risk of fire, textiles which have

traces of any flammable substances such as

vegetable oil, cooking oil, machine oil,

flammable chemicals, thinner, etc., or anything

containing wax or chemicals such as in mops and

cleaning cloths, must not be put into the washer.

These flammable substances may cause the

fabric to catch on fire by itself.

18. Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

19. Keep washer in good condition. Bumping or

dropping the washer can damage safety features.

If this occurs, have washer checked by a qualified

service person.

20. Be sure water connections have a shut-off valve

and that fill hose connections are tight. CLOSE

the shut-off valves at the end of each wash day.

21. Loading door MUST BE CLOSED any time the

washer is to fill, tumble or spin. DO NOT bypass

the loading door switch by permitting the washer

to operate with the loading door open.

22. Always read and follow manufacturer’s

instructions on packages of laundry and cleaning

aids. Heed all warnings or precautions. To reduce

the risk of poisoning or chemical burns, keep

them out of the reach of children at all times

(preferably in a locked cabinet).

23. Always follow the fabric care instructions

supplied by the textile manufacturer.

24. Never operate the washer with any guards and/or

panels removed.

25. DO NOT operate the washer with missing or

broken parts.

26. DO NOT bypass any safety devices.

27. Failure to install, maintain, and/or operate this

washer according to the manufacturer’s

instructions may result in conditions which can

produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT

SAFETY INSTRUCTIONS appearing in this

manual are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining, or operating the washer.

Any problems or conditions not understood should be

reported to the dealer, distributor, service agent or the

manufacturer.

Safety Information

F8112301

IMPORTANT: Ensure that the recommended

clearances for inspection and maintenance are

provided. Never allow the inspection and

maintenance space to be blocked.

Safety Decals

Safety decals appear at crucial locations on the

machine. Failure to maintain legible safety decals

could result in injury to the operator or service

technician.

To provide personal safety and keep the machine in

proper working order, follow all maintenance and

safety procedures presented in this manual. If

questions regarding safety arise, contact the

manufacturer immediately.

Use manufacturer–authorized spare parts to avoid

safety hazards.

This machine must be installed, adjusted,

and serviced by qualified electrical

maintenance personnel familiar with the

construction and operation of this type of

machinery. They must also be familiar

with the potential hazards involved.

Failure to observe this warning may result

in personal injury and/or equipment

damage, and may void the warranty.

SW004

WARNING

Install the machine on a level floor of

sufficient strength. Failure to do so may

result in conditions which can produce

serious injury, death and/or property

damage.

W703

CAUTION

Be careful around the open door,

particularly when loading from a level

below the door. Impact with door edges

can cause personal injury.

SW025

CAUTION

Never touch internal or external steam

pipes, connections, or components.

These surfaces can be extremely hot and

will cause severe burns. The steam must

be turned off and the pipe, connections,

and components allowed to cool before

the pipe can be touched.

SW014

WARNING

Safety Information

F8112301

Operator Safety

To ensure the safety of machine operators, the

following maintenance checks must be performed

daily:

1. Prior to operating machine, verify that all

warning signs are present and legible. Missing or

illegible signs must be replaced immediately.

Make certain that spares are available.

2. Check door interlock before starting operation of

machine:

a. Attempt to start machine with door open.

Machine should not start with door open.

b. Close door without locking it and attempt to

start machine. Machine should not start with

door unlocked.

c. Close and lock door and start a cycle. Attempt

to open door while cycle is in progress. Door

should not open.

If door lock and interlock are not functioning

properly, call a service technician.

3. Do not attempt to operate machine if any of the

following conditions are present:

a. Door does not remain securely locked during

entire cycle.

b. Excessively high water level is evident.

c. Machine is not connected to a properly

grounded circuit.

Do not bypass any safety devices in machine.

Safe Operating Environment

Safe operation requires an appropriate operating

environment for both the operator and the machine. If

questions regarding safety arise, contact the

manufacturer immediately.

Environmental Conditions

●Ambient Temperature. Water in machine will

freeze at temperatures of 32°F (0°C) or below.

Temperatures above 120°F (50°C) will result in

more frequent motor overheating and, in some

cases, malfunction or premature damage to solid

state devices that are used in some models.

Special cooling devices may be necessary.

Water pressure switches are affected by increases

and decreases in temperature. Every 25°F (10°C)

change in temperature will have a 1% effect on

the water level.

●Humidity. Relative humidity above 90% may

cause machine’s electronics or motors to

malfunction or may trip ground fault interrupter.

Corrosion problems may occur on some metal

components in machine.

If relative humidity is below 30%, belts and

rubber hoses may eventually develop dry rot.

This condition can result in hose leaks, which

may cause safety hazards external to machine in

conjunction with adjacent electrical equipment.

●Ventilation. The need for make-up air openings

for such laundry room accessories as dryers,

ironers, water heaters, etc., must be evaluated

periodically. Louvers, screens or other separating

devices may reduce available air opening

significantly.

●Radio Frequency Emissions. A filter is available

for machines in installations where floor space is

shared with equipment sensitive to radio

frequency emissions.

●Elevation. If machine is to be operated at

elevations of over 3280 feet (1000 m) above sea

level, pay special attention to water levels and

electronic settings (particularly temperature) or

desired results may not be achieved.

●Chemicals. Keep stainless steel surfaces free of

chemical residues.

NEVER insert hands or objects into

basket until it has completely stopped.

Doing so could result in serious injury.

SW012

WARNING

Never operate the machine with a

bypassed or disconnected balance

system. Operating the machine with

severe out-of-balance loads could result

in personal injury and serious equipment

damage.

SW039

WARNING

Safety Information

F8112301

●Water Damage. Do not spray machine with

water. Short circuiting and serious damage may

result. Repair immediately all seepage due to

worn or damaged gaskets, etc.

Machine Location

●Foundation. The concrete floor must be of

sufficient strength and thickness to handle floor

loads generated by high extract speeds of

machine.

●Service/Maintenance Space. Provide sufficient

space to allow comfortable performance of

service procedures and routine preventive

maintenance.

Consult installation instructions for specific details.

Input and Output Services

●Wat er Pressure. Best performance will be

realized if water is provided at a pressure of 30 –

85 psi (2 – 5.7 bar). Although machine will

function properly at lower pressure, increased fill

times will occur. Water pressure higher than 100

psi (6.7 bar) may result in damage to machine

plumbing. Component failure(s) and personal

injury could result.

●Steam Heat (Optional) Pressure. Best

performance will be realized if steam is provided

at a pressure of 30 – 80 psi (2 – 5.4 bar). Steam

pressure higher than 125 psi (8.5 bar) may result

in damage to steam components and may cause

personal injury.

For machines equipped with optional steam heat,

install piping in accordance with approved

commercial steam practices. Failure to install

supplied steam filter may void warranty.

●Drainage System. Provide drain lines or troughs

large enough to accommodate total number of

gallons that could be released if all machines on

site drained at same time from highest attainable

level. If troughs are used, they should be covered

to support light foot traffic.

●Power. For personal safety and for proper

operation, machine must be grounded in

accordance with state and local codes. Ground

connection must be to a proven earth ground, not

to conduit or water pipes. Do not use fuses in

place of circuit breaker. An easy-access cutoff

switch should also be provided.

Always disconnect power and water supplies before a

service technician performs any service procedure.

Where applicable, steam and/or compressed air

supplies should also be disconnected before service is

performed.

Do not place volatile or flammable fluids

in any machine. Do not clean the machine

with volatile or flammable fluids such as

acetone, lacquer thinners, enamel

reducers, carbon tetrachloride, gasoline,

benzene, naptha, etc. Doing so could

result in serious personal injury and/or

damage to the machine.

SW002

DANGER

Replace all panels that are removed to

perform service and maintenance

procedures. Do not operate the machine

with missing guards or with broken or

missing parts. Do not bypass any safety

devices.

SW019

CAUTION

Ensure that a ground wire from a proven

earth ground is connected to the ground

lug near the input power block on this

machine. Without proper grounding,

personal injury from electric shock could

occur and machine malfunctions may be

evident.

SW008

WARNING

Safety Information

F8112301

DirectDrive

Machines equipped with DirectDrive require special

attention with regard to operating environment.

●An especially dusty or linty environment will

require more frequent cleaning of AC inverter

drive cooling fan filter and of AC inverter drive

itself.

●Power line fluctuations from sources such as

uninterruptible power supplies (UPS) can

adversely affect machines equipped with AC

inverter drive. Proper suppression devices should

be utilized on incoming power to machine to

avoid problems.

●A clean power supply free from voltage spikes

and surges is absolutely essential for machines

equipped with AC inverter drive. Inconsistencies

(peaks and valleys) in power supply can cause

AC inverter drive to generate nuisance errors.

If voltage is above 230 Volt for 200 Volt

installation or 460 Volt for 400 Volt installation,

ask power company to correct. As an alternative,

a step-down transformer kit is available from

distributor. If voltage is above 240 Volt for 200

Volt installation or 480 Volt for 400 Volt

installations, a buckboost transformer is required.

●Sufficient space to perform service procedures

and routine preventive maintenance is especially

important for machines equipped with AC

inverter drive.

Otros manuales para CP040PMN1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arandela de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems AWN432SP113TW01 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TLW12CTLW12C Guía

Alliance Laundry Systems

Alliance Laundry Systems HC18PC2 Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems 802733R4 Guía

Alliance Laundry Systems

Alliance Laundry Systems UWN045K2M Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems UW100VV Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen FR7002WN Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HFNBCF Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems HCD020GD2 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TLW12C SVG Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems UM202 Series Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems HWF561 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems AWN43RSN115CW01 Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen TC5000WN Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HC18PC2 Manual de programación

Alliance Laundry Systems

Alliance Laundry Systems HWFB61WN1102 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems DWA021*A Instrucciones de montaje

Alliance Laundry Systems

Alliance Laundry Systems Dishwasher Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Cabinet Hardmount SC27SN Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems LWK73AW-3050 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 800797 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems AR105M X CONTROL Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems AWNA11SP111TW01 Manual de programación

Alliance Laundry Systems

Alliance Laundry Systems P Series Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario