Alliance Laundry Systems 512906 Manual de usuario

Page 1 of 4

Product Information

Subject Programming Timer

Use With Coin Slide Control

Coin Slide Control

Power-Up Mode

When power is applied to the dryer, the control will

enter the Ready Mode. If the control was powered

down during a running a cycle, the IN USE LED will

flash once and the control will enter Start Mode. If the

dry time dipswitch settings have not been changed

from factory default, the IN USE LED will flash once.

Ready Mode

In Ready Mode, the control waits for the vend to be

satisfied before entering Start Mode.

Start Mode

In Start Mode, the vend has been satisfied, but the

Start button has not been pressed. The IN USE LED

will be lit. The timer will not count down until the

Start button is pressed.

Run Mode

In Run Mode, the control is running a cycle. The

IN USE LED is lit.

Door Open Mode

In Door Open Mode, the control turns off the heater

and motor when the door is opened during a run cycle.

The timer will continue to count down time and the

IN USE LED is lit.

End of Cycle Mode

In End of Cycle Mode, a cycle is complete and the

IN USE LED is off. The control remains in this mode

until the door is opened or additional vend has been

satisfied.

Topoffs

Any time the control receives a coin slide pulse during

a cycle it will add the programmed dry time to the time

currently remaining in the cycle. The IN USE LED

will flash briefly to indicate the coin input. The

maximum cycle time is 99 minutes. The control will

not add time beyond 99 minutes. The cool down time

will not change. If the control receives a coin slide

pulse during cool down it will exit cool down and start

heating with the cycle time equal to the programmed

time.

Temperature Selector Switch

For five minutes after the control is powered up, there

is a diagnostic feature that allows the temperature

selector switches to be tested. When the temperature

selector is changed, the new setting is displayed by

flashing the IN USE LED as follows:

High/Normal: 4 flashes

Medium/PP: 3 flashes

Low/Delicate: 2 flashes

No Heat: 1 flash

Part No. 512906

February 2007

Page 2 of 4

(512906)

Error Display Mode

The control enters Error Display Mode to display

thermistor errors. The heater is turned off, the IN USE

LED flashes to indicate the error (refer to paragraphs

below), and the timer will continue to count down

time. The control remains in Error Display Mode until

the control senses the thermistor has returned to an

acceptable heating range, the cycle ends or machine is

powered down.

Open Thermistor

If the control senses a temperature less than 0°F when

the heat has been on for at least three minutes it will

set an open thermistor error. The control will flash the

IN USE LED twice separated by a one and a half

second pause. This sequence is repeated as long as the

Open Thermistor error is sensed.

Shorted Thermistor

If the control senses a temperature greater than 210 ±

4°F during an active cycle it will set a Shorted

Thermistor error. The control will flash the IN USE

LED three times separated by a one and a half second

pause. This sequence is repeated as long as the Shorted

Thermistor error is sensed.

Setting Dry Time Dipswitches

To change the dry time on the dryer, combinations of

dipswitches can be set on the control.

There are eight dipswitches on the dryer control. The

first six switches are used to program the amount of

additional heat time given for each coin pulse. The

additional drying time is added to the factory default

minimum heat time of one minute. A value of 1 to 63

minutes of additional drying time is available for each

coin slide pulse.

The last two switches are used to program the amount

of additional cool down time. The additional cool

down time is added to the factory default minimum

cool down time of 3 minutes. A value of 1 to 3

additional minutes is available.

The control is shipped from the factory programmed

with 1 minute of minimum heat time, preset with 41

additional minutes of drying time (dipswitches 1, 4

and 6 in ON position) and 3 minutes of minimum cool

down time for a total time of 45 minutes for a coin

pulse. Refer to Table 1 for dipswitch settings.

The control reads the dipswitch settings at power-up.

The control must be powered down to change the

dipswitch settings.

To change the heat or cool down time for a coin pulse,

the desired dry time dipswitches must be set to ON

position. All other dipswitches must be in OFF

position.

Page 3 of 4

(512906)

Dipswitch Settings

Heat Switch Number

Heat Time Per Coin Pulse

(in minutes) 1 2 3 4 5 6

1OFF OFF OFF OFF OFF OFF

2ON OFF OFF OFF OFF OFF

3OFF ON OFF OFF OFF OFF

4ON ON OFF OFF OFF OFF

5OFF OFF ON OFF OFF OFF

6ON OFF ON OFF OFF OFF

7OFF ON ON OFF OFF OFF

8 ON ON ON OFF OFF OFF

9OFF OFF OFF ON OFF OFF

10 ON OFF OFF ON OFF OFF

11 OFF ON OFF ON OFF OFF

12 ON ON OFF ON OFF OFF

13 OFF OFF ON ON OFF OFF

14 ON OFF ON ON OFF OFF

15 OFF ON ON ON OFF OFF

16 ON ON ON ON OFF OFF

17 OFF OFF OFF OFF ON OFF

18 ON OFF OFF OFF ON OFF

19 OFF ON OFF OFF ON OFF

20 ON ON OFF OFF ON OFF

21 OFF OFF ON OFF ON OFF

22 ON OFF ON OFF ON OFF

23 OFF ON ON OFF ON OFF

24 ON ON ON OFF ON OFF

25 OFF OFF OFF ON ON OFF

26 ON OFF OFF ON ON OFF

27 OFF ON OFF ON ON OFF

28 ON ON OFF ON ON OFF

29 OFF OFF ON ON ON OFF

30 ON OFF ON ON ON OFF

31 OFF ON ON ON ON OFF

32 ON ON ON ON ON OFF

33 OFF OFF OFF OFF OFF ON

34 ON OFF OFF OFF OFF ON

35 OFF ON OFF OFF OFF ON

36 ON ON OFF OFF OFF ON

37 OFF OFF ON OFF OFF ON

38 ON OFF ON OFF OFF ON

Table 1 (continued)

Page 4 of 4

(512906)

Table 1 (continued)

Heat Switch Number

Heat Time Per Coin Pulse

(in minutes) 1 2 3 4 5 6

39 OFF ON ON OFF OFF ON

40 ON ON ON OFF OFF ON

41 OFF OFF OFF ON OFF ON

42 (preset at factory) ON OFF OFF ON OFF ON

43 OFF ON OFF ON OFF ON

44 ON ON OFF ON OFF ON

45 OFF OFF ON ON OFF ON

46 ON OFF ON ON OFF ON

47 OFF ON ON ON OFF ON

48 ON ON ON ON OFF ON

49 OFF OFF OFF OFF ON ON

50 ON OFF OFF OFF ON ON

51 OFF ON OFF OFF ON ON

52 ON ON OFF OFF ON ON

53 OFF OFF ON OFF ON ON

54 ON OFF ON OFF ON ON

55 OFF ON ON OFF ON ON

56 ON ON ON OFF ON ON

57 OFF OFF OFF ON ON ON

58 ON OFF OFF ON ON ON

59 OFF ON OFF ON ON ON

60 ON ON OFF ON ON ON

61 OFF OFF ON ON ON ON

62 ON OFF ON ON ON ON

63 OFF ON ON ON ON ON

64 ON ON ON ON ON ON

Cool Down Per Cycle Cool Down Switch Number

(in minutes) 7 8

3 (preset at factory) OFF OFF

4ON OFF

5OFF ON

6ON ON

Table 1

Total Cycle Time = Heat Time + Cool Down Time

Tabla de contenidos

Otros manuales de Secadora de Alliance Laundry Systems

Alliance Laundry Systems

Alliance Laundry Systems DRY725C_SVG Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems SDE807 Guía

Alliance Laundry Systems

Alliance Laundry Systems LES37A*F Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems DRY735C SVG Series Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen FF7009WN Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems SFE107*A Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 907003062 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems D355IE1B Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems 510988R3 Guía

Alliance Laundry Systems

Alliance Laundry Systems 70420801 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 602004144 Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems 70223701R2 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems D0582 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems ADEE9BSS Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems CHD25G2-CT025L Instrucciones de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems DR3003WX Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems HSE117*C802 Instrucciones de montaje

Alliance Laundry Systems

Alliance Laundry Systems JT30XG Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems W800 Guía de solución de problemas

Alliance Laundry Systems

Alliance Laundry Systems DRY684C Guía

Alliance Laundry Systems

Alliance Laundry Systems 504522R3 Manual del propietario

Alliance Laundry Systems

Alliance Laundry Systems Drying Tumblers none Manual de funcionamiento

Alliance Laundry Systems

Alliance Laundry Systems Drying Tumbler 110 Pound Capacity Part No.... Manual de instalación y operación

Alliance Laundry Systems

Alliance Laundry Systems T433I Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario

Frigidaire

Frigidaire CAQE7077KW0 Manual del propietario

Bosch

Bosch WTX8HKM9SN Manual de usuario