allen WB2434 Manual de usuario
SAFETY, ASSEMBLY &
PARTS MANUAL
Manual Part #: 068523 | Revision: B
Language: English | Original Instructions
WORK BRIDGES
WB2434
068521
Page 2
SAFETY, ASSEMBLY & PARTS MANUAL
This manual covers the products listed below:
Part No. Description
- WB2434, Work Bridge
Work Bridge
Copyright © 2019 Allen Engineering Corporation
All rights reserved
All information, specifications, and illustrations in this manual are subject to change without notice and are based on the latest infor-
mation at the time of publication. No part of this manual may be reproduced or transmitted in any form or by any means, electronics
or mechanical, for any purpose, without the express written permission of Allen Engineering Corporation (AEC). AEC assumes no
responsibility or liability for any errors or inaccuracies that may appear in this manual.
Allen Products are covered under one or more of the following patent numbers:
10,100,537; 9,068,301; 9,068,300; 8,360,680; 7,690,864; 7,114,876B1; 6,857,815B2; 6,582,153
With other Patents Pending.
Printed in U.S.A.
This manual, or a copy of it, must be kept with the machine at all times.
There is a manual storage container located on the machine for your convenience.
068521 Page 3
GENERAL
INFORMATION
Allen Engineering Corporation (“Allen”) warrants its products to be free of defects in material or workmanship
for:
TWO YEARS FROM END USER’S DATE OF PURCHASE
Warranty period begins on the date of purchase by the End User of the product. All warranty is based on the
following limited warranty terms and conditions, including the disclaimer of implied warranties and consequen-
tial damages.
1. Allen’s obligation and liability under this warranty is limited to repairing or replacing parts if, after Allen’s inspection, there is determined
to be a defect in material or workmanship. Allen reserves the choice to repair or replace.
2. If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen Distributor, Dealer, or
Rental Center from whom the End User purchased the product.
3. Replacement or repair parts, installed in the product, are warranted only for the remainder of warranty period of the product as though
they were the original parts.
4. Allen does not warranty engines or batteries. Engine warranty claims should be made directly to an authorized factory service center
for the particular engine manufacturer. Batteries are not warranted due to unknown treatment during transport, etc, and any battery
claims should be directed to the battery manufacturer.
5. Allen’s warranty does not cover the normal maintenance of products or its components (such as engine tuneups and oil & lter chang-
es). The warranty also does not cover normal wear and tear items (such as belts and consumables).
6. Allen’s warranty will be void if it is determined that the defect resulted from operator abuse, failure to perform normal maintenance on
the product, modication to product, alterations or repairs made to the product without the written approval of Allen. Allen specically
excludes from warranty any damage to any trowels resulting from an impact to the rotors.
7. Impact damage to gear boxes is not covered under the Allen warranty and is deemed customer abuse.
8. Allen will pay shop labor on warranty items at the Allen Shop Labor Rate in existence on the date of the warranty claim. An Allen labor
chart will determine the time allowed to complete a repair and will govern the shop labor hours that will be allowed.
9. Allen will pay freight on warranty replacement parts at worldwide standard ground rates. No warranty replacement parts will be
shipped air freight at the expense of Allen. Allen only pays outbound freight charges when sending warranty replacement parts to the
customer via ground service. Allen does not pay any inbound freight. However, if Allen determines this to be a warranted item, only then
will Allen reimburse the customer for inbound freight at standard ground rates.
10. ALLEN ENGINEERING CORPORATION’S WARRANTY POLICY WILL NOT COVER THE FOLLOWING: TAXES; SHOP SUPPLIES; ENVIRON-
MENTAL SURCHARGES; AIR FREIGHT; TRAVEL TIME; LOSS OF TIME; INCONVENIENCE; LOSS OF RENTAL REVENUE; RENTAL COSTS OF
EQUIPMENT USED TO REPLACE THE PRODUCT BEING REPAIRED; LOSS OF USE OF THE PRODUCT; COMMERCIAL LOSS; OR ANY OTHER
CHARGES WHATSOEVER OR ANY LIABILITIES FOR DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE OR DELAY.
11. ALLEN ENGINEERING CORPORATION MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED. THIS LIMITED WARRANTY IS IN LIEU OF
THE WARRANTY OF MERCHANTABILITY AND FITNESS. THERE ARE NO OTHER WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION
ON THIS DOCUMENT.
12. No Allen employee or representative is authorized to change this warranty in any way or grant any other warranty unless such change
is made in writing and signed by an ofcer of Allen Engineering Corporation.
Limited Warranty
GENERAL
INFORMATION
068521
Page 4
Table of Contents
Sect Title Page
- General Information
Limited Warranty ................................................................................ 3
Load Capacity Ratings ........................................................................ 5
Information Contained in This Manual................................................. 6
Dealer Information / Ordering Parts..................................................... 7
Model Number - Serial Number Codes................................................ 8
Technical Specifications ..................................................................... 9
1.0 Safety .............................................................................................. 10
Federal / State Warning Regulations ................................................. 11
Manual Tag Safety Detail.................................................................. 12
Spark Arrestor Notice / Hazard Symbols ........................................... 13
Operating Safety ............................................................................... 14
Engine Safety.................................................................................... 15
Service Safety................................................................................... 16
Lifting Safety .................................................................................... 17
Transportation Safety........................................................................ 19
2.0 Assembly......................................................................................... 20
Assembly Instructions....................................................................... 21
3.0 Parts ................................................................................................ 26
Mainframe Sizes............................................................................... 27
Mainframe Assembly - 3 Foot........................................................... 28
Mainframe Assembly - 6 Foot........................................................... 29
Mainframe Assembly - 12 Foot......................................................... 30
Adjustable End Frame Bracket .......................................................... 31
Mainframe Assembly - Telescoping, 15-25 Foot............................... 32
Mainframe Assembly - Telescoping, Opposite End, 15-25 Foot ........ 34
Bridge Deck End Bracket Assembly .................................................. 36
Power Wheel Conversion Kit ............................................................. 38
WB Power Wheel, Power Unit ........................................................... 40
Bridge Deck Style Wheel Options...................................................... 42
Decal Kit........................................................................................... 44
Cleaning Procedure........................................................................... 46
Revision Detail.................................................................................. 47
068521 Page 5
GENERAL
INFORMATION
Load Capacity Ratings
Notes on Load Capacity Ratings:
1. Maximum span/rating with 12 ft sections (x10): 121ft @ 600lbs
• Total span above INCLUDES End Frame and Wheels
• Total span of SECTIONS ONLY: 120 ft
2. All ratings are calculated using the largest sections available to achieve desired length.
• Excluding telescoping sections.
3. Load ratings are calculated using pneumatic tires.
4. Deection should exceed no more than 1.36” with Maximum span/weight applied.
5. Cable Tensioning Kit may be used to increase load capacity on larger workbridges. This is NOT recomended without
consulting an AEC product support specialist or Authorized AEC dealer FIRST!
6. Calculations are done without factoring weather. Please note that in adverse weather conditions, capacity ratings
need to be decreased.
Please contact Allen Engineering PRODUCT SUPPORT with any questions reguarding load capacity.
500
700
900
1100
1300
1500
1700
1900
2100
2300
55 60 65 70 75 80 85 90 95 100 105 110 115 120 125
RATEDCAPACITY
(inPounds)
SPAN
(inFeet)
WB2434‐ CapacityRatings
GENERAL
INFORMATION
068521
Page 6
This manual provides information and procedures to safely operate and maintain the Allen Machine.
For your own safety and protection from personal injury, carefully read, understand, and observe the safety instructions
described in this manual. Keep this manual or a copy of it with the machine at all times.
Always operate this machine in accordance with the instructions described in this manual. A well maintained piece of
equipment will provide many years of trouble free operation.
This manual is divided into the following sections:
Complete any warranty requirements as specified by the engine manufacturer in their instructions found inside the
manual box located on the back of the riding trowel operator’s seat.
Your engine and clutch is not manufactured by Allen Engineering Corporation, Inc, and therefore is not covered under
Allen Engineering Corporation, Inc warranty.
Your engine manufacturer should be contacted if you wish to purchase a parts manual or a repair manual for your engine.
Refer to enclosed owners engine manual for complete O&M instructions. See your battery manufacturer for battery
warranty.
SECTION 1
SAFETY
SECTION 2
ASSEMBLY
Information Contained
in this Manual
SECTION 3
PARTS
068521 Page 7
GENERAL
INFORMATION
Dealer Information /
Ordering Parts
Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts. Always contact
the Allen Dealer who sold you this machine for Allen Certified repairs and replacement parts.
Place Allen Dealer information below for future reference.
Dealer Name:
Dealer Phone #:
( ) - -
Address:
City / State / Zip:
Salesman:
Salesman Phone #:
Addistional Comments:
The “PARTS & DECALS MANUAL” contain illustrated parts lists for help in ordering replacement parts for your machine.
Follow the instructions below when ordering parts to insure prompt and accurate delivery:
1. All orders for service parts - include the serial number for the machine. Shipment will be delayed if this information
is not available.
2. Include correct description and part number from the “PARTS & DECALS MANUAL”
3. Specify exact shipping instructions, including the preferred routing and complete destination address.
4. DO NOT return parts to AEC without receiving written authorization from AEC. All authorized returns must be shipped
pre-paid.
5. When placing an order, please contact the AEC dealer nearest you.
ALL INFORMATION, SPECIFICATIONS, AND ILLUSTRATIONS IN THIS MANUAL
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ARE BASED ON THE LAT-
EST INFORMATION AT THE TIME OF PUBLICATION.
GENERAL
INFORMATION
068521
Page 8
Model Number / Serial Number
Manufacturer’s Codes:
When ordering parts or requesting service information, you will always be asked to specify the model
and serial numbers of the machine. The legends below specically denes each signicant character
or group of characters of the Model Number and Serial Number codes.
Model Number
WB 2434
Series
2434 (24” High x 34” Wide)
Work Bridge
068521 Page 9
GENERAL
INFORMATION
Technical Specications
These work bridges are ideal for joint work, applying curing compounds, bull-oating, applying tex-
tures or whenever a suitable platform for doing bridge work is required. The Allen Work Bridge is an
economical workhorse on any job site.
Work Bridge 2434
Dimensions (H x W x L) 24” x 34”
Section Lengths:
3’
6’
12’
15’-25’ {Telescopic}
Maximum Length (Feet) 120
Minimum Height (in) {Top of Deck} 15
Maximum Height (in) {Top of Deck} 60
Weight
3 FT Section: 97 lbs
-Powered: 102 lbs
6 FT Section: 169.5 lbs
-Powered: 179.5 lbs
12 FT Section: 250 lbs
-Powered: 275lbs
Telescopic Section: 916 lbs
-Powered: 951 lbs
Wheels Flanged Style for Forms
Cupped Style for Pipe Rails
SECTION 1
SAFETY
068521
Page 10
SECTION 1
SAFETY
Tabla de contenidos
Otros manuales de Equipos de construcción de allen
allen
allen AT-16 Guía de aplicación
allen
allen AW16-B Guía
allen
allen RS844 Guía de aplicación
allen
allen BDF4836 Manual de usuario
allen
allen SE12 Guía de aplicación
allen
allen WB1224 Manual de usuario
allen
allen SSE12 Guía de aplicación
allen
allen AT14F Guía de aplicación
allen
allen WB1824 Manual de usuario
allen
allen AW16-B Manual de usuario
