allen SSE12 Guía de aplicación
OPERATIONS & PARTS MANUAL
SSE12 SCREED
Manual Part #: 064633 I REVISION: B
This manual, or a copy of it, must be kept with the machine at all times.
There is a manual storage container located on the machine for your
convenience.
Engine Driven Screed
OPERATIONS - PARTS MANUAL
This manual covers the products listed below:
Part No. Description
028379 Screed, Truss, Steel, Engine Driven, SSE12,10.0’ Section (3.1m)
022378 Screed, Truss, Steel, Engine Driven, SSE12, 7.5’ Section (2.3m)
022379 Screed, Truss, Steel, Engine Driven, SSE12, 5’ Section (1.5m)
027986 Screed, Truss, Steel, Engine Driven, SSE12, 2.5’ Section (.76m)
022380 Screed, Truss, Steel, Engine Driven, SSE12, 2’ Section (.61M)
050362Page 4
Section Title Page
--- Limited Warranty .........................................................................................................4
--- Table of Contents ........................................................................................................5
--- Information Contained In This Manual..........................................................................7
--- Dealer Information.......................................................................................................8
--- Ordering Parts .............................................................................................................9
--- Model Number - Serial Number Codes ......................................................................10
--- UnitIdentication ......................................................................................................11
--- Technicalspecications.............................................................................................12
--- EngineSpecications ................................................................................................13
--- LiftingSpecications .................................................................................................14
--- Transportation ...........................................................................................................15
--- Standard Machine Dimensions ..................................................................................16
Section 1 - Safety
1.1 State Regulations ......................................................................................................18
1.2 Federal Regulations...................................................................................................19
1.3 Safety Information.....................................................................................................20
1.4 Safety Symbols .........................................................................................................21
1.5 General Safety...........................................................................................................22
1.6 Sound & Vibration Analysis ........................................................................................29
Section 2 - Operations
2.1 Pre-Operating Instructions.........................................................................................32
2.2 Operating Instructions ...............................................................................................33
2.3 Lifting Procedures .....................................................................................................34
2.4 Section Assembly ......................................................................................................35
2.5 Attaching Winches.....................................................................................................36
2.6 Determining Left and Right........................................................................................37
2.7 End Handle Assembly................................................................................................38
2.8 Engine Mount assembly ............................................................................................39
2.9 String Lining..............................................................................................................40
Section 3 - Service
3.1 Periodic Maintenance Schedule.................................................................................42
Table of Contents
050362 Page 5
Section 4 - Parts
--- Factory Service Information.......................................................................................44
--- Replacement Parts Procedures..................................................................................45
4.1 Engine Mount............................................................................................................46
4.2 2’ Section..................................................................................................................48
4.3 2- 1/2’ Section ..........................................................................................................50
4.4 5’ Section..................................................................................................................52
4.5 7- 1/2’ Section ..........................................................................................................54
4.6 10’ Section................................................................................................................56
4.7 End Handle................................................................................................................58
4.8 Winch Assembly........................................................................................................60
4.9 Hydraulic Winch Assembly.........................................................................................62
4.10 Flex Coupler ..............................................................................................................66
4.11 U-Joint......................................................................................................................67
4.12 Crown Invert Bracket.................................................................................................68
4.13 End Mount Engine Assembly......................................................................................70
4.14 Decals, Standard SSE12............................................................................................72
4.15 Decals, Hydraulic.......................................................................................................73
--- Revision Details.........................................................................................................74
--- Copyright Information................................................................................................75
Table of Contents, continued
050362Page 6
Allen Engineering Corporation (“Allen”) warrants its products to be free of defects in material or workmanship for:
TWO YEARS FROM END USER’S DATE OF PURCHASE
Warranty period begins on the date of purchase by the End User of the product. All warranty is based on the following limited warranty
terms and conditions, including the disclaimer of implied warranties and consequential damages.
1. Allen’s obligation and liability under this warranty is limited to repairing or replacing parts if, after Allen’s inspection, there is de-
termined to be a defect in material or workmanship. Allen reserves the choice to repair or replace.
2. If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen Distributor, Dealer,
or Rental Center from whom the End User purchased the product.
3. Replacement or repair parts, installed in the product, are warranted only for the remainder of warranty period of the product as
though they were the original parts.
4. Allen does not warranty engines or batteries. Engine warranty claims should be made directly to an authorized factory service
center for the particular engine manufacturer. Batteries are not warranted due to unknown treatment during transport, etc, and
any battery claims should be directed to the battery manufacturer.
5. Allen’swarrantydoesnotcoverthenormalmaintenanceofproductsoritscomponents(suchasenginetuneupsandoil<er
changes). The warranty also does not cover normal wear and tear items (such as belts and consumables).
6. Allen’s warranty will be void if it is determined that the defect resulted from operator abuse, failure to perform normal maintenance
ontheproduct,modicationtoproduct,alterationsorrepairsmadetotheproductwithoutthewrittenapprovalofAllen.Allen
specicallyexcludesfromwarrantyanydamagetoanytrowelsresultingfromanimpacttotherotors.
7. Impact damage to gear boxes is not covered under the Allen warranty and is deemed customer abuse.
8. Allen will pay shop labor on warranty items at the Allen Shop Labor Rate in existence on the date of the warranty claim. An Allen
labor chart will determine the time allowed to complete a repair and will govern the shop labor hours that will be allowed.
9. Allen will pay freight on warranty replacement parts at worldwide standard ground rates. No warranty replacement parts will be
shipped air freight at the expense of Allen. Allen only pays outbound freight charges when sending warranty replacement parts to
the customer via ground service. Allen does not pay any inbound freight. However, if Allen determines this to be a warranted item,
only then will Allen reimburse the customer for inbound freight at standard ground rates.
10. ALLEN ENGINEERING CORPORATION’S WARRANTY POLICY WILL NOT COVER THE FOLLOWING: TAXES;
11. SHOP SUPPLIES; ENVIRONMENTAL SURCHARGES; AIR FREIGHT; TRAVEL TIME; LOSS OF TIME; INCONVENIENCE; LOSS OF RENTAL
REVENUE; RENTAL COSTS OF EQUIPMENT USED TO REPLACE THE PRODUCT BEING REPAIRED;
12. LOSS OF USE OF THE PRODUCT; COMMERCIAL LOSS; OR ANY OTHER CHARGES WHATSOEVER OR ANY LIABILITIES FOR DIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGE OR DELAY.
13. ALLEN ENGINEERING CORPORATION MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED. THIS LIMITED WARRANTY IS IN
LIEU OF THE WARRANTY OF MERCHANTABILITY AND FITNESS. THERE ARE NO OTHER WARRANTIES THAT EXTEND BEYOND THE
DESCRIPTION ON THIS DOCUMENT.
14. No Allen employee or representative is authorized to change this warranty in any way or grant any other warranty
15. unlesssuchchangeismadeinwritingandsignedbyanofcerofAllenEngineeringCorporation.
Limited Warranty
050362 Page 7
This manual provides information and procedures to safely operate and maintain the Allen Machine.
For your own safety and protection from personal injury, carefully read, understand, and observe the
safety instructions described in this manual. Keep this manual or a copy of it with the machine at all
times.
ALWAYS operate this machine in accordance with the instructions described in this manual. A well main-
tained piece of equipment will provide many years of trouble free operation.
This manual is divided into the following sections:
Complete any warranty requirements as specified by the engine manufacturer in their instructions found
inside the manual box located on the back of the riding trowel operator’s seat.
Your engine and clutch is not manufactured by Allen Engineering Corporation, Inc, and therefore is not
covered under Allen Engineering Corporation, Inc warranty.
Your engine manufacturer should be contacted if you wish to purchase a parts manual or a repair man-
ual for your engine.
Refer to enclosed owners engine manual for complete O&M instructions. See your battery manufacturer
for battery warranty.
SECTION 1
SAFETY
SECTION 2
OPERATIONS
SECTION 3
SERVICE
SECTION 4
PARTS
Information Contained
In This Manual
050362Page 8
Dealer Name: _____________________________________________________________
Phone #: (____) - ____ - ____________________________________________________
Address: ________________________________________________________________
City:__________________________________State:________ Zip:___________________
Salesman: _______________________________Mobile Phone _____________________
Additional Comments: ______________________________________________________
________________________________________________________________________
________________________________________________________________________
Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts. Always contact the
AllenDealerwhosoldyouthismachineforAllenCertiedrepairsandreplacementparts.
Place Allen Dealer information below for future reference.
Dealer Information
050362 Page 9
Ordering Parts
Section 4.0 contains illustrated parts lists for help in ordering replacement parts for your machine. Follow the instructions
below when ordering parts to insure prompt and accurate delivery:
1. All orders for service parts - include the serial number for the machine. Shipment will be delayed if this information
is not available.
2. Include correct description and part number from the “PARTS” section of this manual.
3. Specify exact shipping instructions, including the preferred routing and complete destination address.
4. DO NOT return parts to AEC without receiving written authorization from AEC. All authorized returns must be shipped
pre-paid.
5. When placing an order, please contact the AEC dealer nearest you.
ALL INFORMATION, SPECIFICATIONS, AND ILLUSTRATIONS IN THIS MANUAL ARE
SUBJECT TO CHANGE WITHOUT NOTICE AND ARE BASED ON THE LATEST
INFORMATION AT THE TIME OF PUBLICATION.
050362Page 10
Manufacturer’s Codes:
When ordering parts or requesting service information, you will ALWAYS be asked to specify the model and serial numbers
ofthemachine.Thelegendsbelow specicallydeneseachsignicant character or group ofcharactersof the Model
Number and Serial Number codes.
Model Number
T150 B
Series
B
Triple Roller Tube Paver
150
Serial Number
Theserialnumberfoundontheidenticationplateisatendigitformat.Themodelnumberidentiesyourmachineandwill
ensure that you receive the correct replacement parts.
Serial Number Example
T15 14 01 180
Series
Sequence Number
Year
Month
Model Number - Serial Number Codes
Tabla de contenidos
Otros manuales de Equipos de construcción de allen
allen
allen TRTP150B Guía de aplicación
allen
allen AT-16 Guía de aplicación
allen
allen WB2434 Manual de usuario
allen
allen WB1224 Manual de usuario
allen
allen SE12 Guía de aplicación
allen
allen BDF4836 Manual de usuario
allen
allen TRTP75 Guía
allen
allen BDF6048B Guía
allen
allen TRTP275 Guía de aplicación
allen
allen RS844 Guía de aplicación
