Allen-Bradley ArmorBlock LP2 Manual de usuario

1792D-5.49 - August 1999

Installation Instructions

ArmorBlock LP2 16 Sourcing

Output Module

(Cat. No. 1792D-OBT16LP)

This ArmorBlock LP2™ I/O module (Cat. No. 1792D-0BT16LP) is a

stand-alone 24V dc I/O product which communicates via a DeviceNet™

network. The sealed housing of this module requires no enclosure.

This model has 16 sourcing outputs accessed through Y splitter cables.

Outputs are self protected 24V dc and provide up to 0.3A each.

42049

O-4

O-5

O-6

O-7

O-11

O-10

O-2

O-3

O-13

O-12

O-9

O-8

Network Status Module Status

O-0

O-1

O-15

O-14

Auxiliary Power

2ArmorBlock LP2 16 Sourcing Output Module

1792D-5.49 - August 1999

Package Contents

Your package contains:

•1 ArmorBlock LP2 Module

•Installation Instructions

European Union Directive Compliance

If this product has the CE mark it is approved for installation within the

European Union and EEA regions. It has been designed and tested to meet

the following directives.

EMC Directive

This product is tested to meet Council Directive 89/336/EC

Electromagnetic Compatibility (EMC) and the following standards, in

whole or in part, documented in a technical construction file:

•EN 50081-2 EMC - Generic Emission Standard, Part 2 - Industrial

Environment

•EN 50082-2 EMC - Generic Immunity Standard, Part 2 - Industrial

Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low Voltage,

by applying the safety requirements of EN 61131-2 Programmable

Controllers, Part 2 - Equipment Requirements and Tests.

For specific information required by EN 61131-2, see the appropriate

sections in this publication, as well as the following Allen-Bradley

publication Industrial Automation Wiring and Grounding Guidelines For

Noise Immunity, publication 1770-4.1.

ArmorBlock LP2 16 Sourcing Output Module 3

1792D-5.49 - August 1999

Install Your ArmorBlock LP2 I/O Module

To install the module:

•Mount the module and attach the unit to the DeviceNet trunk.

•Set the node address and baud rate.

•Connect the output cord sets to the LP2 module.

•Communicate with your ArmorBlock LP2 module.

More detailed information about each of these steps is in the following

procedures.

Mount the Module and Attach the Unit to the Devicenet Trunk

1. Mount the module using the dimensions shown below.

2. Connect the grey DeviceNet cable to the DeviceNet trunk. Use the

1485P-P1R5-MN5R1 T-Part tap to make the connection to round

media. Use the 1485P-P1E4-R5 to connect to the Kwik Link flat media

system.

3. Connect the black auxiliary power cable to your 24V dc power source.

Set the Node Address and Baud Rate

Set the node address using RSNetWorx for DeviceNet™software,

DeviceNetManager™ software, or another software configuration tool. The

module is equipped with AutoBaud detect. AutoBaud lets the module read

the settings already in use on your DeviceNet network and automatically

adjusts to follow those settings.

O-4

O-5

O-6

O-7

O-11

O-10

O-2

O-3

O-13

O-12

O-9

O-8

Network Status Module Status

O-0

O-1

O-15

O-14

Auxiliary Power

42049

4.21in

107mm

0.25in

6.25mm

12in

305mm

1.95in

49.5mm

6.85in

174mm

2.7in

68.5mm

(width)

4ArmorBlock LP2 16 Sourcing Output Module

1792D-5.49 - August 1999

Connect the Output Cord Sets to the LP2 Module

This module uses 5 pole micro (12mm) style PCB mounted connectors.

Eight micro caps cover the connectors on your module. Remove the caps

and connect your cables to the appropriate ports. This product has two

outputs per connector. Use a “Y” splitter cable for access to all output

connections. For more information on these cables, see the Product Data

guide, publication 1792-2.1.

Use the micro caps to cover and seal unused ports. A pinout diagram for

the connectors is shown below.

ATTENTION:

•Make sure all connectors and caps are securely tightened

to properly seal the connections against leaks and

maintain IP67 requirements.

•For maximum noise immunity, output cable return wires

must be properly terminated. When outputs are

connected in loopback, return wires should be connected

together.

•I/O cable length should be less than 30 meters.

Output Micro-Connector

(View into Sockets)

Pin 1 Not Used

Pin 2 Output B

Pin 3 Auxiliary Power Return

Pin 4 Output A

Pin 5 Not Used 41452

ArmorBlock LP2 16 Sourcing Output Module 5

1792D-5.49 - August 1999

Output connectors for this module are shown below.

Communicate with Your ArmorBlock LP2 Module

This ArmorBlock module’s I/O is exchanged with the master through a

polled, change of state, or cyclic connection.

The module produces output data as follows:

Cyclic - allows configuration of the block as an I/O client. The block will

consume and produce its I/O cyclically at the rate configured.

Polled - a master initiates communication by sending its polled I/O

message to the module. The 16 output module consumes the message,

updates outputs, and producing a response. The response has output faults

and the status of the Auxiliary power.

Type of I/O Connections Consumes Produces

Cyclic 2 Bytes 1 Byte

Polled 2 Bytes 1 Byte

Change of State 2 Bytes 1 Byte

O-4

O-5

O-6

O-7

O-11

O-10

O-2

O-3

O-13

O-12

O-9

O-8

Network Status Module Status

O-0

O-1

O-15

O-14

Auxiliary Power

42049

Output 0

Output 1

Output 2

Output 3

Output 4

Output 5

Output 6

Output 7

Output 15

Output 14

Output 13

Output 12

Output 11

Output 10

Output 9

Output 8

Connector A

Connector B

Connector C

Connector D

Connector H

Connector G

Connector F

Connector E

6ArmorBlock LP2 16 Sourcing Output Module

1792D-5.49 - August 1999

Change of state -productions occur when an output changes or a fault

condition occurs. If no output or fault condition change occurs within the

expected packet rate, a heartbeat production occurs. This heartbeat

production tells the scanner module that the I/O module is alive and ready

to communicate. Consumption occurs when data changes and the master

produces new output data to the I/O block.

Refer to the table below for the word/bit definitions.

The DeviceNet Network uses advanced network technology, producer/

consumer communication, to increase network functionality and

throughput. Visit our website at http://www.ab.com/networks for producer/

consumer technology information and updates.

Bit 0706050403020100

Produces 0 RSVD OPWR RSVD RSVD RSVD RSVD RSVD RSVD

Consumes 0 O7 O6 O5 O4 O3 O2 O1 O0

Consumes 1 O15 O14 O13 O12 O11 O10 O9 O8

Where: O = Output RSVD = Reserved OPWR = Output Power (Auxiliary Power)

Byte Bit Description

Produces 0 00-05

Reserved

OPWR = Output power fault, Auxiliary Power is not present

Reserved

Consumes 0 00-07 Output bits - when the bit is set (1), the output will be

turned on. Bit 00 corresponds to output 0, bit 01

corresponds to output 1, bit 02 to output 2, bit 03 to output

3, bit 04 to output 4, bit 05 to output 5, bit 06 to output 6,

and bit 07 to output 7

Consumes 2 08-07 Output bits - when the bit is set (1), the output will be

turned on. Bit 00 corresponds to output 8, bit 01

corresponds to output 9, bit 02 to output 10, bit 03 to

output 11, bit 04 to output 12, bit 05 to output 13, bit 06 to

output 14, and bit 07 to output 15

ArmorBlock LP2 16 Sourcing Output Module 7

1792D-5.49 - August 1999

Troubleshoot with the Indicators

This module has the following indicators:

•Network status indicator

•Module status indicator

•Individual point status indicators for outputs 0 through 15

The following table describes the module status indicator.

Module Status Indicator

Indication Status

None No Power

Green

Blinking

Solid

Needs Commissioning

Operating Normal

Red

Blinking

Solid

Recoverable Fault

Unrecoverable Fault

O-4

O-5

O-6

O-7

O-11

O-10

O-2

O-3

O-13

O-12

O-9

O-8

Network Status Module Status

O-0

O-1

O-15

O-14

Auxiliary Power

42049-M

Point indicators for

outputs 0 and 1

DeviceNet

Indicators

Connector A

Connector B

Connector C

Connector D

Connector H

Connector G

Connector F

Connector E

Point indicators for

outputs 2 and 3

Point indicators for

outputs 4 and 5

Point indicators for

outputs 6 and 7

Point indicators for

outputs 8 and 9

Point indicators for

outputs 10 and 11

Point indicators for

outputs 12 and 13

Point indicators for

outputs 14 and 15

LED Assignments

8ArmorBlock LP2 16 Sourcing Output Module

1792D-5.49 - August 1999

The following table describes the network status and Auxiliary power

indicators.

The following table describes I/O status indicators.

For more information on indications, see the Product Data, publication

1792-2.1.

Network Status Indicator

Indication Status

None Not On-line

Green

Blinking

Solid

On-line/No Connections

On-line/Connected

Red

Blink

Solid

Connection Timed Out

Failed Communication: A duplicate

node address exists or the module is at

the wrong baud rate.

Auxiliary Power

Indication Status

None No Auxiliary Power

Green

Solid Auxiliary Power Present

I/O Status Indicators

Function Module Status Indicator Point Indicator Condition

Outputs Green

Green

None

Yellow

Output not energized

Output energized

ArmorBlock LP2 16 Sourcing Output Module 9

1792D-5.49 - August 1999

Specifications

16 Output Module - Cat. No. 1792D-OBT16LP

Sourcing Output Specifications Max Min

Outputs per block 16 sinking outputs labeled 00 through 15

Output Auxiliary Voltage 30V 10V

On-state Voltage Drop 1V -

On-state Current 0.3A -

Off-state Leakage 1.5mA -

Module Current (all outputs) 4.0A -

Surge Current - for 10 ms,

repeatable every 2s

0.6A -

Indicators Network Status - red/green

Module Status - red/green

Auxiliary Power - green

Point LED - yellow

Communication Rate •125Kbps @ 500 meters(1600 feet) for thick

cable, flat media length 375 meters

•250Kbps @ 200 meters(600 feet) for thick

cable, flat media length 150 meters

•500Kbps @ 100 meters (330 feet) for thick

cable, flat media length 75 meters

DeviceNet Power Voltage

Current

25V dc

125mA

11V dc

250mA

Auxiliary Power Voltage

Current

30V dc

10V dc

Dimensions (assembled to base)

inches - (Millimeters)

1.023H x 2.7W x6.85D

(26)H x (68.5)W x (174)D

Environmental Conditions

Operational Temperature

Storage Temperature

Relative Humidity

Shock Operating

Non-operating

Vibration

-25 to 60oC (-13 to 140oF)

-25 to 80oC (-13 to 176OF)

Up to 100%

30g peak acceleration, 11 (+1) ms pulse width

50g peak acceleration, 11(+1)ms pulse width

Tested 10g @ 10-500Hz per IEC 68-2-6

Conductors Publication DN-6.7.2

Enclosure Meets or exceeds IP67

Agency Certification

(when product is marked)

•CE marked for all applicable directives

10 ArmorBlock LP2 16 Sourcing Output Module

1792D-5.49 - August 1999

This product has been tested at an Open DeviceNet Vendor Association,

Inc. (ODVA) authorized independent test laboratory and found to comply

with ODVA Conformance Test. Please contact the ODVA website

(http://www.odva.org) for listing of products tested by ODVA independent

test labs for further details.

Tabla de contenidos

Otros manuales de Sistema de E/S de Allen-Bradley

Allen-Bradley

Allen-Bradley 1794-IM8 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-IB Guía de instalación y uso

Allen-Bradley

Allen-Bradley 1746-IA4 Manual de usuario

Allen-Bradley

Allen-Bradley 1794-IB8 Manual de usuario

Allen-Bradley

Allen-Bradley ArmorBlock MaXum 4 Manual de usuario

Allen-Bradley

Allen-Bradley POINT I/O Manual de usuario

Allen-Bradley

Allen-Bradley E300 Manual de usuario

Allen-Bradley

Allen-Bradley 1757-PIM Manual de usuario

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IG16 Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-IF6CIS Manual de usuario

Allen-Bradley

Allen-Bradley 1746-NT8 Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-IH16ISOE Manual de usuario

Allen-Bradley

Allen-Bradley C Series Manual de usuario

Allen-Bradley

Allen-Bradley 1734-OE4C Manual de usuario

Allen-Bradley

Allen-Bradley FLEX Ex 1797-IRT8 Manual de usuario

Allen-Bradley

Allen-Bradley 1756 ControlLogix Manual de usuario

Allen-Bradley

Allen-Bradley 1734-IB8S Manual de instrucciones

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IB10XOB6 Manual de usuario

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IC16 Manual de usuario

Allen-Bradley

Allen-Bradley Flex I/O Manual de usuario

Allen-Bradley

Allen-Bradley 1734-IM4 Manual de usuario

Allen-Bradley

Allen-Bradley SLC 500 Manual de usuario

Allen-Bradley

Allen-Bradley 1492-CM1771-LD005 Manual de usuario

Allen-Bradley

Allen-Bradley 1738-IR2M12 Manual de operación

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario