Allen-Bradley ControlNet 1788-CNCR Manual de usuario

Publication 1788-IN002C-EN-P - April 2004

Installation Instructions

ControlNet Daughtercard

Catalog Numbers 1788-CNC and 1788-CNCR

This document describes how to install and configure the ControlNet 1788-CNC and

-CNCR daughtercards. In this document, we use the term ‘the card’ to refer to both

daughtercards collectively. When one card is different from the other, we refer to the

daughtercard by name.

If you are connecting the card directly to a ControlNet network, you should also refer to these

publications:

•ControlNet Tap Installation Instructions, publication 1786-5.7

•ControlNet Coax Media Planning and Installation Guide, publication CNET-IN002

For information about See page

Important User Information 2

European Hazardous Location Approval 4

North American Hazardous Location Approval 5

About the Daughtercards 6

Setting the Node Address 7

Installing the Card 8

Daughtercard Performance 8

Connecting the Card to the Network 8

Connect to the Network Using a Tap 10

Connect to the Network Using a 1786-CP Cable 12

Interpreting the Status Indicators 14

Specifications 17

6ControlNet Daughtercard

Publication 1788-IN002C-EN-P - April 2004

About the Daughtercards

The network daughtercard architecture defines a common

hardware and software interface that several different

network interface cards will support. This allows products

that have been designed to support the network

daughtercard option to support several different Rockwell

Automation networks.

About the ControlNet Daughtercard

You can install the 1788-CNC or -CNCR ControlNet daughtercard in any host device that

supports the ControlNet daughtercard.(1)

Every ControlNet network requires at least one module that is able to store parameters and

configure the network with those parameters upon start-up. This module is called a ‘keeper’

since it keeps the network configuration.

Any 1788-CNC or -CNCR card can keep the network parameters at any legal node address

(01 to 99). Multiple devices on any one network can act as the network keeper. Each device

capable of being the network keeper acts to back up the current keeper. This backup function

is automatic and requires no action on your part.

WARNING •If you connect or disconnect the communications cable with

power applied to this module or any device on the network, an

electrical arc can occur. This could cause an explosion in

hazardous location installations.

•If you insert or remove the card while host power is on, an

electrical arc can occur. This could cause an explosion in

hazardous location installations.

•Be sure that power is removed or the area is nonhazardous

before proceeding.

(1) The host device must provide a suitable power source per the restrictions in the specifications table.

IMPORTANT On the 1788-CNC or -CNCR card, the non-volatile keeper data is erased

when a firmware update is performed.

ControlNet Daughtercard 7

Publication 1788-IN002C-EN-P - April 2004

Setting the Node Address

You must set two switch assemblies to configure the daughtercard with its unique network

address. Figure 1 shows the location of the switches. These switches are read on powerup to

establish the network address of the card.

Set the node address to a value between 01 and 99. For optimum throughput, assign

addresses to your ControlNet nodes in a sequential order starting with 01.

Node address 00 is not a valid ControlNet address. You should only use node address 00 if

the product that uses the ControlNet daughtercard has the ability to set the node address

using the host device interface.

This feature is typically used on products that do not allow easy customer access to the node

address switches. If you set the node address switch to 00, it allows the host in which the

daughtercard resides to set the node address, rather than allowing the daughtercard to read

the node address from the switch settings.

Figure 1 Setting the Node Address

31044-M

I/O

status

LED

module

status

LED

NAP

node address

switches

network status indicators (A and B)

channel A connector

channel B connector

8ControlNet Daughtercard

Publication 1788-IN002C-EN-P - April 2004

Installing the Card

Due to wide variation in available host devices, we cannot provide specific installation

instructions in this document. For instructions on how to install the daughtercard in a host

device, refer to the user manual for the particular host device.

Daughtercard Performance

Due to wide variation in available host devices, we cannot provide specific performance

capabilities in this document. For information concerning host/daughtercard performance

characteristics, refer to the user manual for the particular host device.

Connecting the Card to the Network

After you have installed the card, you can connect it to the network. You must connect the

card to the network using an approved ControlNet tap:

•1786-TPR (T-tap right angle)

•1786-TPS (T-tap straight)

•1786-TPYR (Y-tap right angle)

•1786-TPYS (Y-tap straight)

We recommend the straight taps.

IMPORTANT Do not install or remove the daughtercard while the host is under power.

ControlNet Daughtercard 9

Publication 1788-IN002C-EN-P - April 2004

Figure 2 1788-CNCR Daughtercard

When you connect the daughtercard to a ControlNet network, you should also refer to this

documentation:

•ControlNet Coax Tap Installation Instructions, publication 1786-5.7

•ControlNet Coax Media Planning and Installation Guide, publication CNET-IN002

See page 14 for information about status indicators.

IMPORTANT If you use a non-redundant cable system, all ControlNet devices must be

on the same channel, we recommend channel A.

example ControlNet node example ControlNet node

trunk cable A

trunk cable B

example ControlNet node

12 ControlNet Daughtercard

Publication 1788-IN002C-EN-P - April 2004

Connect to the Network Using a 1786-CP Cable

Follow this illustration to connect a programming terminal to the network using a 1786-CP

cable.

ATTENTION Use the 1786-CP cable when you connect a programming terminal to the

network through the network access port (NAP); using another cable

could result in possible network failures or product damage.

The NAP port is for temporary local programming purposes only and not

intended for permanent connection.

1786-CP

cable

Any ControlNet

interface card

ControlNet network

1The 1786-CP cable can be plugged into any ControlNet product's NAP to provide programming

capability on the ControlNet network. A programming terminal connected through this cable is

counted as a node and must have a unique address.

31074

ControlNet Daughtercard 17

Publication 1788-IN002C-EN-P - April 2004

Specifications

Characteristic Value

Operational Temperature IEC 60068-2-1 (Test Ad, Operating Cold),

IEC 60068-2-2 (Test Bd, Operating Dry Heat),

IEC 60068-2-14 (Test Nb, Operating Thermal Shock):

0 to 60°C (32 to 140°F)

It is accebtable for the ambient slot temperature immediately surrounding this

product to reach 85°C (185°F) maximum

Storage Temperature IEC 60068-2-1 (Test Ab, Un-packaged Non-operating Cold),

IEC 60068-2-2 (Test Bb, Un-packaged Non-operating Dry Heat),

IEC 60068-2-14 (Test Na, Un-packaged Non-operating Thermal Shock):

-40 to 85°C (-40 to 185°F)

Relative Humidity IEC 60068-2-30 (Test Db, Un-packaged Non-operating Damp Heat):

5 to 95% non-condensing

Vibration IEC 60068-2-6 (Test Fc, Operating):

5g @ 10-500Hz

Operating Shock IEC 60068-2-27 (Test Ea, Unpackaged Shock):

30g

Non-Operating Shock IEC 60068-2-27 (Test Ea, Unpackaged Shock):

50g

Emissions CISPR 11:

Group 1, Class A

ESD Immunity IEC 61000-4-2:

6kV contact discharges

8kV air discharges

Radiated RF Immunity IEC 61000-4-3:

10V/m with 1kHz sine-wave 80%AM from 30MHz to 1000MHz

10V/m with 200Hz 50% Pulse 100%AM at 900Mhz

EFT/B Immunity IEC 61000-4-4:

±4kV at 2.5kHz on communications ports

Surge Transient Immunity IEC 61000-4-5:

±2kV line-earth(CM) on shielded ports

Conducted RF Immunity IEC 61000-4-6:

10Vrms with 1kHz sine-wave 80%AM from 150kHz to 80MHz

Enclosure Type Rating None (open-style)

Power Requirements(1)

1788-CNC

1788-CNCR

5V dc @ 450 mA (maximum)

5V dc @ 475 mA (maximum)

Power Consumption

1788-CNC

1788-CNCR

2.25 watts

2.375 watts

Power Dissipation

1788-CNC

1788-CNCR

2.25 watts or 7.68 BTU/hour

2.375 watts or 8.1 BTU/hour

Wiring Category(2) 2 - on communications ports

18 ControlNet Daughtercard

Publication 1788-IN002C-EN-P - April 2004

Weight

1788-CNC, 1788-CNCR

0.1 Kg (0.2 lb)

Agency Certification

(when product is marked)

c-UR-us: UL Recognized Component Industrial Control Equipment, certified for

US and Canada

c-UR-us: UL Recognized Component Industrial Control Equipment for Class I,

Division 2, Group A,B,C,D Hazardous Locations, certified for US and Canada

CSA: CSA Certified Process Control Equipment

CSA: CSA Certified Process Control Equipment for Class I, Division 2, Group

A,B,C,D Hazardous Locations

CE(3):European Union 89/336/EEC EMC Directive, compliant with:

EN 50082-2; Industrial Immunity

EN 61326; Meas./Control/Lab., Industrial Requirements

EN 61000-6-2; Industrial Immunity

EN 61000-6-4; Industrial Emissions

C-Tick(3):Australian Radiocommunications Act, compliant with:

AS/NZS CISPR 11; Industrial Emissions

EEx(3):European Union 94/9/EC ATEX Directive, compliant with:

EN 50021; Potentially Explosive Atmospheres, Protection "n" (Zone 2)

CI: ControlNet International conformance tested to ControlNet specifications

(1) To comply with UL and CSA restrictions, this equipment must be powered from a source compliant with the following: Class

2 or Limited Voltage/Current, as defined in UL 508 Seventeenth Edition Section 32; and Separated Extra-Low-Voltage

(SELV), as defined in CSA C22.2 No 1010, Annex H.

(2) Use this Conductor Category information for planning conductor routing. Refer to Publication 1770-4.1, "Industrial

Automation Wiring and Grounding Guidelines".

(3) See the Product Certification link at www.ab.com for Declarations of Conformity, Certificates, and other certification

details.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Allen-Bradley

Allen-Bradley

Allen-Bradley CompactLogix EtherNet/IP 1768-EWEB Manual de usuario

Allen-Bradley

Allen-Bradley Micro800 2080-MEMBAK-RTC2 Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-DMD30 Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet 1747-ACN15 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-IXHR Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF6VI Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Manual de usuario

Allen-Bradley

Allen-Bradley Series B Manual de usuario

Allen-Bradley

Allen-Bradley A Series Manual de usuario

Allen-Bradley

Allen-Bradley 1747-KE Manual de usuario

Allen-Bradley

Allen-Bradley Entek XM-123 Manual de usuario

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-DH485 Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Manual de usuario

Allen-Bradley

Allen-Bradley MicroLogix 1200 Manual de usuario

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet C Series Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Manual de usuario

Allen-Bradley

Allen-Bradley 1440-DYN02-01RJ Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OB16D Manual de usuario

Allen-Bradley

Allen-Bradley ProcessLogix R300.1 Manual de usuario

Allen-Bradley

Allen-Bradley CENTERLINE 2100 Manual de usuario

Allen-Bradley

Allen-Bradley CENTERLINE 1500 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario