Allen-Bradley 1407-CGCM Manual de usuario

Combination Generator Control Module

Catalog Numbers 1407-CGCM

User Manual

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required

to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the

use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

Allen-Bradley, Rockwell Software, Rockwell Automation, ControlLogix, Logix5000, and RSLogix are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014 

3UMMARYOF#HANGES

This manual contains new and updated information. Changes throughout this

revision are marked by change bars, as shown to the right of this paragraph.

.EWAND5PDATED

)NFORMATION

This table contains the changes made to this revision.

4OPIC 0AGE

Updated the dimension diagrams 14

Updated the Configuration Messaging section 129

Added information for the Network status indicator 164

Added information for the Module status indicator 165

Updated the Get Attributes All (service code 0x01) table for Identity

Object Instance 1 198

Updated the Get Attributes All (service code 0x01) table for Identity

Object Instance 2 199

Added a Device Status for Identity Object Instance 2 199

Updated the Certification information in the Agency Certifications

table 210

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014

3UMMARYOF#HANGES

.OTES

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014 

4ABLEOF#ONTENTS

0REFACE

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

#HAPTER

'ENERAL)NFORMATION

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

#HAPTER

)NSTALLATION

Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

#HAPTER

#'#-5NIT/PERATION

Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Operational Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

#HAPTER

#'#-5NIT#ONFIGURATION

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Overview of the Configuration Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Create a New Module in the ControlLogix Controller . . . . . . . . . . . . . . 72

Device Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

#HAPTER

#'#-5NIT3TARTUP

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Recommended Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Recommended Start-up Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Document Configuration Parameter and Wiring Changes. . . . . . . . . . 125

#HAPTER

#'#-5NIT3OFTWARE)NTERFACE

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

CGCM Unit User Program Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

CGCM Unit Data Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

#HAPTER

4ROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

!PPENDIX!

4IME/VERCURRENT

#HARACTERISTIC#URVES

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Curve Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Time Over-current Characteristic Curve Graphs. . . . . . . . . . . . . . . . . . . 170

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014

4ABLEOF#ONTENTS

!PPENDIX"

#'#-5NIT-ATH-ODELS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Synchronous Machine Terminal Voltage Transducer and Load

Compensator Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

VAR/Power Factor Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

Limiters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

V/Hz Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

Soft Start Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

Field Current Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

!PPENDIX#

!DDITIONAL#ONTROL.ET.ETWORK

)NFORMATION

ControlNet Application Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

!PPENDIX$

3PECIFICATIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201

!PPENDIX%

$ETAILED#'#-5NIT4AG

$ESCRIPTIONS

Generator Parameters and Configuration Status . . . . . . . . . . . . . . . . . . . 213

General Excitation Control Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

AVR Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

FCR Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216

Power Factor Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

VAR Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218

Excitation Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219

Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

Synchronizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228

Load Sharing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233

Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

!PPENDIX&

#ONFIGURATION2ECORD

7ORKSHEET

Generator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237

)NDEX

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014 

0REFACE

The information in this manual applies to the 1407-CGCM module, Series D,

Revision A, with host firmware revision 4.25 and ControlNet firmware

revision 1.07. The manual notes differences with earlier versions of the product

where they occur.

!DDITIONAL2ESOURCES

These documents contain additional information concerning related products

from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/

literature/. To order paper copies of technical documentation, contact your local

Allen-Bradley distributor or Rockwell Automation sales representative.

2ESOURCE $ESCRIPTION

Safety Guidelines for the Application,

Installation and Maintenance of Solid State

Controls, publication SGI-1.1

Describes some important differences between

solid-state equipment and hard-wired

electromechanical devices.

ControlNet Coax Media Planning and

Installation, publication CNET-IN002 Provides installation procedures for the

ControlNet network.

Logix5000™ Controllers Common Procedures,

publication 1756-PM001 Provides information about RSLogix™ 5000

software.

CGCM Release Notes, publication 1407-RN001 Provides information on compatible RSLogix

5000 software versions and ControlLogix®

controller firmware revisions.

Industrial Automation Wiring and Grounding

Guidelines, publication 1770.4.1.Provides general guidelines for installing a

Rockwell Automation industrial system.

Product Certifications website,

http://www.ab.com Provides declarations of conformity, certificates,

and other certification details.

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014

0REFACE

.OTES

Rockwell Automation Publication 1407-UM001H-EN-P - November 2014 

#HAPTER



'ENERAL)NFORMATION

)NTRODUCTION

The Combination Generator Control Module (CGCM unit) is a

microprocessor-based control and protection device. The CGCM unit is

designed to integrate with a Logix family programmable controller to provide

generator control, protection and synchronization functions. Programmability of

system parameters, regulation settings, and protective functions enable the

CGCM unit to be used in a wide range of applications.

&UNCTIONS

The following sections outline the functions of the unit.

'ENERATOR2EGULATIONAND#ONTROL&UNCTIONS

This list contains the generator regulation and control functions:

•Four excitation control modes

•Automatic voltage regulation (AVR)

•Manual or field current regulation (FCR)

•Power factor (PF)

•Reactive power (VAR)

•Soft start voltage buildup with an adjustable ramp in AVR and FCR

control modes

•Over-excitation (OEL) and under-excitation (UEL) limiting in AVR,

VAR, and PF control modes

•Under-frequency compensation (Volts/Hertz)

•Line drop compensation

•Auto-tracking between operating modes and between redundant CGCM

units

•Automatic transfer to a back-up CGCM unit in redundant systems

•Generator paralleling with reactive droop compensation or cross-current

(reactive differential) compensation

•Generator paralleling with real power load sharing

•Synchronizing for one or two circuit breakers

 Rockwell Automation Publication 1407-UM001H-EN-P - November 2014

#HAPTER General Information

'ENERATOR0ROTECTION&UNCTIONS

This list contains the generator protection functions:

•Loss of excitation current (40)

•Over-excitation voltage (59F)

•Generator over-voltage (59)

•Generator under-voltage (27)

•Loss of sensing (60FL)

•Loss of permanent magnet generator

(PMG/Excitation power) (27)

•Reverse VAR (40Q)

•Over-frequency (81O)

•Under-frequency (81U)

•Reverse power (32R)

•Rotating diode monitor

•Phase rotation error (47)

•Generator over-current (51)

-ETERING&UNCTIONS

This list contains the metering functions:

•Voltag e

•Current

•Frequency

•Real Power

•Apparent Power

•Reactive Power

•Power Factor

•Real Energy (kWh)

•Apparent Energy (kVAh)

•Reactive Energy (kVARh)

•Controller Excitation Current and Voltage

•Diode Monitor Ripple Level

•Load Share Error

•Synchronization Parameters

Tabla de contenidos

Otros manuales de Unidad de control de Allen-Bradley

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Manual de usuario

Allen-Bradley

Allen-Bradley 1747-DTAM-E Manual de usuario

Allen-Bradley

Allen-Bradley 1492-CM1771-LD007 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-OBN Manual de usuario

Allen-Bradley

Allen-Bradley E300 Manual de usuario

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manual de usuario

Allen-Bradley

Allen-Bradley 1734-IB8S Manual de usuario

Allen-Bradley

Allen-Bradley CAB6-HA 2 Manual de usuario

Allen-Bradley

Allen-Bradley E Series Manual de usuario

Allen-Bradley

Allen-Bradley 1785-KE Manual de usuario

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Manual

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Manual de usuario

Allen-Bradley

Allen-Bradley Entek XM-123 Manual de usuario

Allen-Bradley

Allen-Bradley DeviceNet 1771-SDN/C Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Manual de usuario

Allen-Bradley

Allen-Bradley 1792-IB16 Series B Manual de usuario

Allen-Bradley

Allen-Bradley 1771-QRD Manual de usuario

Allen-Bradley

Allen-Bradley ControlLogix 1756-DMD30 Manual de usuario

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Manual de usuario

Allen-Bradley

Allen-Bradley ArmorBlock 1732D A Series Manual de usuario

Allen-Bradley

Allen-Bradley SLC 500 DeviceNet Manual de usuario

Allen-Bradley

Allen-Bradley 1492-IFM40F-3 Manual de usuario

Allen-Bradley

Allen-Bradley D Series Manual de usuario

Allen-Bradley

Allen-Bradley 1336 PLUS II Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario