Allen-Bradley 1792-IB16 Series B Manual de usuario
ArmorBlock is a trademark of Allen-Bradley Co. Inc.
Publication 1792-5.3 – October 1996
Cat. No. 1792-IB16 Series B
To: See page:
Install
the ArmorBlock
Module
3
Connect the Wiring to the ArmorBlock Module
8
Communicate with Y
our ArmorBlock Module
10
Configure Y
our ArmorBlock Module Of
fline Using the DeviceNet
Manager Configuration T
ool 11
Configure Y
our ArmorBlock Module Online Using the DeviceNet
Manager Configuration T
ool 17
Reset Faults 25
Configure Y
our ArmorBlock Module with EDS Files
28
For this reference information
See page:
Default Configuration
14
Status indicators
38
Troubleshooting 38
Specifications 39
This 1792 ArmorBlockI/O block module (Cat. No. 1792-IB16)
contains I/O circuits, a built-in power supply, and a built-in DeviceNet
I/O adapter. Because of its sealed housing, this 1792 I/O block requires
no enclosure. It is compatible with PLC or SLC programmable
controllers using DeviceNet scanners. The I/O values are accessible
from the PLC or SLC programmable controller data table.
This ArmorBlock module has no switches to set. You set module
parameters using the DeviceNet Manager Software (cat. no.
1787-MGR) or similar configuration tool.
Installation Instructions
ArmorBlock 16 Input Module2
Publication 1792-5.3 – October 1996
European Union Directive Compliance
If this product is installed within the European Union or EEA regions
and has the CE mark, the following regulations apply.
EMC Directive
This apparatus is tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC) using a technical construction
file and the following standards, in whole or in part:
•EN 50081-2 EMC – Generic Emission Standard, Part 2 –
Industrial Environment
•EN 50082-2 EMC – Generic Immunity Standard, Part 2 –
Industrial Environment
The product described in this manual is intended for use in an industrial
environment.
Low Voltage Directive
This apparatus is also designed to meet Council Directive 73/23/EEC
Low Voltage, by applying the safety requirements of EN 61131–2
Programmable Controllers, Part 2 – Equipment Requirements and
Tests.
For specific information that the above norm requires, see the
appropriate sections in this manual, as well as the following
Allen-Bradley publications:
•Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1
•Automation Systems Catalog, publication B111
3
ArmorBlock 16 Input Module
Publication 1792-5.3 – October 1996
Install
Y
our ArmorBlock Module
Installation of the ArmorBlock module consists of:
•setting the node address in the ArmorBlock module
•mounting the ArmorBlock module
•connecting the wiring
•communicating with your module
•configuring the parameters
Set the Node Address
Each ArmorBlock comes with its internal program set for node address
63. To set the node address, you need the following:
•host computer with DeviceNet Manager Software (or similar
configuration software tool)
•1770-KFD RS-232 module (or similar interface)
•suitable cables to connect the 1770-KFD to your module and to
connect the 1770-KFD to your host computer
Set the node address to meet your system requirements as follows:
1. Set up a system (as shown below) to communicate with your
ArmorBlock module.
Power
from 9V DC Power-Supply Adapter
power supply
open style connector to
sealed mini-female cable
RS-232 module
host computer with the
DeviceNet Manager software
1770-KFD
ArmorBlock 16 Input Module4
Publication 1792-5.3 – October 1996
2. Using DeviceNet Manager Software, go online using the “Setup
Online Connection” selection on the utility pulldown menu.
3. The DeviceNet Driver selection screen appears.
Select the driver for your application and click on .
4. The Driver configuration screen lets you:
•set the data rate
•set the interface adapter node address
•select the interface adapter serial port
•set interface adapter baud rate
Click on to go online.
5
ArmorBlock 16 Input Module
Publication 1792-5.3 – October 1996
5. The bar at the bottom of the screen will tell you when you go online.
6. At the utility pulldown, select “Node Commissioning.”
7. You can set the node address on the “Device Configuration – Node
Commissioning” screen. Note that the node address “out of the box”
setting is 63. Set the desired node address per your system
requirements.
Set new node
address here.
You can also set the data rate on this screen, if required. However,
your module is shipped with the “autobaud” parameter enabled.
This assures that the module will be at the correct data rate for any
network to which it is connected. To change the data rate, you must
first disable autobaud on the parameter screen, then return to the
“Device Configuration – Node Commissioning” screen and enter
the new data rate.
8. Click on to apply the new node settings.
9. Repeat the above procedure to set the node addresses of any
additional ArmorBlock modules you want to install.
ArmorBlock 16 Input Module6
Publication 1792-5.3 – October 1996
Mount the ArmorBlock Module
Mount the block module directly to the machine or device. Complete
mounting dimensions are shown below. Note that the block dimensions
allow direct connection of a T-port tap (cat. no. 1485P-P1N5-j) to the
DeviceNet connector. (Refer to publication 1485-6.7.1 for cabling
details.)
The ArmorBlock module has a sloping top and a gap at the rear to
allow water or other liquids to run off during washdowns. The flow
through the gap prevents buildup of debris under the block.
Preferred mounting position is with the microconnectors pointing
down. However, the block can be mounted in any orientation.
7
ArmorBlock 16 Input Module
Publication 1792-5.3 – October 1996
Mounting Dimensions
6.24
2.63 2.5
7.74
1.90
3.055
4
mounting holes
for #10 screws
MOD/NET
STATUS INPUT
FAULT
NODE
ADDRESS
DATA
RA
TE
ARMORBLOCK
I/O
1792-IB16
(77.6)
(48.3)
(158.5)
(66.7) (63.5)
(196.6)
(184.2)
7
.
25
Inches
(Millimeters)
Block dimensions allow T
-port tap
connection directly onto connector
For washdown installations,
or excessively moist areas,
mount block with micro
connectors down.
Direction of liquid flow
ArmorBlock 16 Input Module8
Publication 1792-5.3 – October 1996
Connect the Wiring to the ArmorBlock Module
The block module uses quick disconnect, screw-on style connectors
for:
•I/O input wiring
•the DeviceNet connector
0
12
3
4
56
7
8
910
11
12
13 14
15
8 micro connectors for 16 input signal wiring
DeviceNet mini connector
Micro plugs are included with your module. Use these plugs to cover
and seal unused ports.
Pinout diagrams for these connectors are shown below.
!ATTENTION: All connectors must be securely
tightened to properly seal the connections against leaks
and maintain NEMA 4X and 6P requirements.
9
ArmorBlock 16 Input Module
Publication 1792-5.3 – October 1996
Connecting the Input Wiring
Connect input wiring to the micro connectors which screw into mating
connectors on the side of the block.
Make connections as shown below.
1
2
3
4
I/O Input Micro Connector
Pin 1 = Sensor Source Voltage Positive
Pin 2 = Signal 2
Pin 3 = Negative/Return
Pin 4 = Signal 1
(View into socket)
The signal 2 pin on the connector is used for 16 input modules only.
Use a splitter cable (or “Y” cable) to access signal 2.
Connecting the DeviceNet Wiring
Connect DeviceNet wiring to the 5-pin mini connector on the end of
the block. Connections are shown below.
1
2
3
DeviceNet Mini Connector Pin 1 = Drain (Bare)
Pin 2 = V+ (Red)
Pin 3 = V– (Black)
(View into pins)
4
5
Pin 4 = CAN–HI (White)
Pin 5 CAN–LO (Blue)
Note: Colors are
DeviceNet standard
ArmorBlock 16 Input Module10
Publication 1792-5.3 – October 1996
Communicate with Your ArmorBlock Module
This ArmorBlock module acts as a slave in a master/slave environment.
It is both a “polled device” and a “change of state device.”
When configured as a polled device, a master initiates communication
by sending its polled I/O message to the ArmorBlock module. The 16
input module scans the inputs and fault bit producing a response that
reflects their status.
When configured as a “change of state” device, productions occur
when an input changes or an input source voltage fault occurs. If
neither has occurred within the “expected packet rate,” a heartbeat
production occurs. This heartbeat production tells the scanner module
that the ArmorBlock module is alive and ready to communicate.
Bit 07 06 05 04 03 02 01 00
Produces 1 I7 I6 I5 I4 I3 I2 I1 I0
Produces 2 I15 I14 I13 I12 I11 I10 I9 I8
Produces 3 S Reserved
Where: I = Input
S = Sensor source voltage fault
Word Bit Description
Produces
100–07 Input bits – bit 00 corresponds to input 0, bit 01 to input 1, and
so on.
0 = input off; 1 = the input is on.
Produces
200–07 Input bits – bit 00 corresponds to input 8, bit 01 to input 9, and so
on.
0 = input off; 1 = the input is on.
Produces 00–06 Reserved
307 Sensor source voltage fault bit – this bit is set (1) when the sensor
source voltage is faulted.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de Allen-Bradley
Allen-Bradley
Allen-Bradley ControlNet 1786-RPFM Manual de usuario
Allen-Bradley
Allen-Bradley 1794-VHSC Manual de usuario
Allen-Bradley
Allen-Bradley ControlNet Ex 1797-RPA Manual de usuario
Allen-Bradley
Allen-Bradley MicroLogix 1500 1764-MM1 Manual de usuario
Allen-Bradley
Allen-Bradley PowerFlex 750 Series Manual de usuario
Allen-Bradley
Allen-Bradley SERCOS 1756-M03SE/A Manual de usuario
Allen-Bradley
Allen-Bradley Kinetix 5700 Manual de usuario
Allen-Bradley
Allen-Bradley ControlNet FLEX Ex 1797-BCNR Manual de usuario
Allen-Bradley
Allen-Bradley POINT I/O 1734-232ASC Manual de usuario
Allen-Bradley
Allen-Bradley ArmorBlock 1732E Manual de usuario
Allen-Bradley
Allen-Bradley Series B Manual de usuario
Allen-Bradley
Allen-Bradley 1794-OA8K Manual de usuario
Allen-Bradley
Allen-Bradley 1785-KE Manual de usuario
Allen-Bradley
Allen-Bradley E300 Manual de usuario
Allen-Bradley
Allen-Bradley DH485/RS-232C Manual de usuario
Allen-Bradley
Allen-Bradley FLEX I/O 1794-IV32 Manual de usuario
Allen-Bradley
Allen-Bradley 1492-CM1771-LD006 Manual de usuario
Allen-Bradley
Allen-Bradley 1718 Ex I/O Manual de usuario
Allen-Bradley
Allen-Bradley ControlLogix 1756-ENBT Manual de usuario
Allen-Bradley
Allen-Bradley ControlLogix 1756-OF4 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
