Allen-Bradley SLC 5/03 Manual de usuario
Publication 1747-IN009C-MU-P - December 2002
Installation Instructions
SLC 5/03™, SLC 5/04™, and SLC 5/05™
Modular Processors
(Catalog Numbers 1747-L531, 1747-L532,
1747-L541, 1747-L542, 1747-L543,
1747-L551, 1747-L552, 1747-L553
1747-L542P, 1747-L543P, 1747-L553P)
To Use Publication
Install your chassis
Installation du châssis
Installation des Chassis
Installazione dello chassis
Instalar el chasis
Instalar o chassi
1746-IN016A-MU-P
Install your power supply
Installation de l’alimentation
Installation des Netzteils
Installazione dell’alimentatore
Instalar la fuente de alimentación eléctrica
Instalar a fonte de energia
1746-IN004B-MU-P
Install your processor
Installation de processeur
Installation des Prozessors
Installazione del processore
Instalar el procesador
Instalar o processador
1747-IN009B-MU-P
English Section.................................... 3
Section en français ........................... 15
Deutscher Abschnitt.......................... 27
Sezione in Italiano............................. 39
Sección en español........................... 51
Seção em português ......................... 63
Allen-Bradley Parts
2
Publication 1747-IN009C-MU-P - December 2002
Publication 1747-IN009C-MU-P - December 2002
Installation Instructions
English Section
SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular
Processors
(Catalog Numbers 1747-L531, 1747-L532,
1747-L541, 1747-L542, 1747-L543,
1747-L551, 1747-L552, 1747-L553,
1747-L542P, 1747-L543P, 1747-L553P)
Inside…........................................................................................ page
Important User Information ................................................................. 4
For More Information........................................................................... 5
Required Tools and Equipment............................................................ 6
Safety Considerations.......................................................................... 6
Installation Procedure.......................................................................... 7
Troubleshooting ................................................................................. 11
Specifications .................................................................................... 11
Battery Handling, Storing, and Transporting (Cat. No. 1747-BA)...... 13
Allen-Bradley Parts
4SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors
Publication 1747-IN009C-MU-P - December 2002
Important User Information
Because of the variety of uses for the products described in this publication, those responsible
for the application and use of this control equipment must satisfy themselves that all
necessary steps have been taken to assure that each application and use meets all performance
and safety requirements, including any applicable laws, regulations, codes and standards.
The illustrations, charts, sample programs and layout examples shown in this guide are
intended solely for purposes of example. Since there are many variables and requirements
associated with any particular installation, Allen-Bradley does not assume responsibility or
liability (to include intellectual property liability) for actual use based upon the examples
shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation, and
Maintenance of Solid-State Control (available from your local Allen-Bradley office), describes
some important differences between solid-state equipment and electromechanical devices
that should be taken into consideration when applying products such as those described in
this publication.
Reproduction of the contents of this copyrighted publication, in whole or in part, without
written permission of Allen-Bradley Company, Inc., is prohibited.
Throughout these installation instructions we use notes to make you aware of safety
considerations:
Attention statements help you to:
•identify a hazard
•avoid the hazard
•recognize the consequences
ATTENTION
!
Identifies information about practices or circumstances that can lead
to personal injury or death, property damage or economic loss.
IMPORTANT Identifies information that is critical for successful application and
understanding of the product.
SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 5
Publication 1747-IN009C-MU-P - December 2002
For More Information
If you would like a manual, you can:
•download a free electronic version from the internet:
www.theautomationbookstore.com
•purchase a printed manual by:
–contacting your local distributor or Rockwell Automation representative
–visiting www.theautomationbookstore.com and placing your order
–calling 1.800.963.9548 (USA/Canada)
or 001.330.725.1574 (Outside USA/Canada)
For Refer to this Document Pub. No.
A more detailed description on how to
install and use your modular SLC 500
system.
SLC 500 Modular Hardware
Style User Manual 1747-UM011C
A reference manual that contains status
file data, instruction set, and
troubleshooting information.
SLC 500 Instruction Set
Reference Manual 1747-RM001C
Allen-Bradley Parts
6SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors
Publication 1747-IN009C-MU-P - December 2002
Required Tools and Equipment
•medium blade screwdriver
•programming equipment
•1747-CP3 cable or appropriate network interface
Safety Considerations
For general recommendations concerning installation safety requirements and safety related
work practices, refer to the requirements specific to your region.
•Europe: Reference the standards found in EN 60204 and your national regulations.
•United States: refer to NFPA 70E, Electrical Safety Requirements for Employee Workplaces.
Network Interface SLC 5/03 SLC 5/04 SLC 5/05
1747-PIC X
1747-CP3 X X X
1747-KTX, -PKTX X(1)
(1) requires 1784-CP14 cable
X(3)
(3) requires 1784-CP13 cable
1747-PCMK X(2)
(2) requires 1784-PCM4 cable
X(4)
(4) requires 1784-PCM6 cable
10Base-T EtherNet X
ATTENTION
!
Never install, remove, or wire any module while power is applied.
Also, do not expose processor modules to surfaces or other areas that
may typically hold an electrostatic charge. Electrostatic charges can
alter or destroy memory.
IMPORTANT See page 13 for information on proper battery handling, storage, and
transporting.
SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 7
Publication 1747-IN009C-MU-P - December 2002
Installation Procedure
Install the Processor
Make sure system power is off; then insert the processor into slot 0 of the 1746 chassis.
Apply Power to the Processor
1. Energize the chassis power supply.
2. Check the chassis power supply and processor LEDs. The power LED on the power
supply should be on and the fault LED on the processor should be flashing. See the
figure on page 8 for location of the power supply and processor LEDs.
IMPORTANT The SLC 500 modular processors must be inserted into the left slot
(slot 0), as shown below. In addition, remove the protective wrap after
installing the processor.
Power Supply
Protective Wrap
Card Guide
Processor Release
Allen-Bradley Parts
8SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors
Publication 1747-IN009C-MU-P - December 2002
Load Your Software
Refer to your programming software documentation.
Establish Communication to the Processor
1. Refer to the following table to establish communication between the processor and
your personal computer.
Processor: Procedure:
SLC 5/03 Connect 1747-PIC from the processor to your personal computer serial port or use a
1784-KTX, -PKTX, or -PCMK interface, or a 1747-CP3 cable from channel 0 of the
processor to the personal computer serial port.
SLC 5/04 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer
serial port or use a 1784-KTX, -PKTX, or -PCMK interface.
SLC 5/05 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer
serial port. For Ethernet connection, connect channel 1 of the processor and the PC
Ethernet Card to an Ethernet hub using 10Base-T compatible cable.(1)
(1) Ethernet IP address must first be set via BOOTP or an RS-232 connection.
POWER RUN
FLT
BATT
FORCE
DH485
RS232
POWER RUN
FLT
BATT
FORCE
DH+
RS232
POWER RUN
FLT
BATT
FORCE
ENET
RS232
Power Supply and LED Indicators
Indicates the LED is OFF
Indicates the LED is ON
Indicates the LED is FLASHING
Status of LED does not matter
SLC 5/05
SLC 5/04
SLC 5/03
SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 9
Publication 1747-IN009C-MU-P - December 2002
2. Set the communication parameters of the software to match the default parameters of
the processor:
Replacing the Battery
Your SLC processor provides back-up power for RAM through a replaceable lithium battery.
This battery provides back-up for approximately 2 years. The BATT LED on the front of the
processor alerts you when the battery voltage has fallen below a threshold level.
To replace the lithium battery follow these steps:
1. Remove power from the SLC 500 power supply.
2. Remove the processor from the chassis by pressing the retainer clips at both the top
and bottom of the module and slide it out.
Channel 0 Configuration Channel 1 Configuration
SLC 5/03, 5/04, 5/05 SLC 5/03 SLC 5/04 SLC 5/05
DF1 Full-Duplex:
•no handshaking
•19.2K baud
•CRC Error Check
•duplicate detect on
•no parity
DH-485:
•19.2K baud
•node address = 1
DH+™:
•57.6K baud
•node address = 1
Ethernet
•BOOTP
enabled
ATTENTION
!
Do not remove the processor from the SLC 500 chassis until all
power is removed from the SLC 500 power supply
ATTENTION
!
Do not expose the processor to surfaces or other areas that may
typically hold an electrostatic charge. Electrostatic charges can alter or
destroy memory.
Allen-Bradley Parts
10 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors
Publication 1747-IN009C-MU-P - December 2002
3. Unplug the battery connector. Refer to the figure on page 10 for battery connector
location.
4. Remove the battery from the retaining clips.
5. Insert a new battery into the battery retaining clips.
6. Plug the battery connector into the socket as shown above.
7. Re-insert the module into the SLC 500 chassis.
8. Restore power to the SLC 500 power supply.
9. Close the processor door.
IMPORTANT The SLC 5/03, 5/04, and 5/05 processors have a capacitor that
provides at least 30 minutes of battery back-up while the battery is
disconnected. Data in RAM is not lost if the battery is replaced within
30 minutes
IMPORTANT See page 13 for information on proper battery handling, storage, and
transporting.
White
Red
Battery Connector
Left Side View
Battery
Otros manuales para SLC 5/03
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Hardware de computadora de Allen-Bradley
Allen-Bradley
Allen-Bradley 1771-SF1 Manual de usuario
Allen-Bradley
Allen-Bradley 1747-DCM Manual de usuario
Allen-Bradley
Allen-Bradley SLC 5/01 Manual de usuario
Allen-Bradley
Allen-Bradley SLC 5/01 Manual de usuario
Allen-Bradley
Allen-Bradley 2707-MVH232 Manual de usuario
Allen-Bradley
Allen-Bradley SLC 500 Series Manual de usuario
Allen-Bradley
Allen-Bradley PLC-5 MAP/OSI Manual de usuario
Allen-Bradley
Allen-Bradley SLC 5/03 Manual de usuario
Allen-Bradley
Allen-Bradley 2094-AL15S Manual de usuario
Allen-Bradley
Allen-Bradley SLC 5/04 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
