Allen-Bradley SLC 5/01 Manual de usuario

Publication 1747-IN011B-MU-P - July 2002

Installation Instructions

SLC 5/01™ and SLC 5/02™ Modular Processors

(Catalog Numbers 1747-L511, 1747-L514, 1747-L524)

Inside .....................................................................................................................page

English Section ..............................................................................................................3

Section en francais......................................................................................................13

Deutscher Abschnitt ....................................................................................................23

Sezione italiana ...........................................................................................................33

Sección en español......................................................................................................43

Allen-Bradley PLCs

2SLC 5/01™ and SLC 5/02™ Modular Processors

Publication 1747-IN011B-MU-P - July 2002

Installation Instructions

English Section

SLC 5/01™ and SLC 5/02™ Modular Processors

(Catalog Numbers 1747-L511, 1747-L514, 1747-L524)

Inside .....................................................................................................................page

Important User Information ......................................................................................... 4

For More Information ................................................................................................... 5

Safety Considerations .................................................................................................. 5

Installation Procedure .................................................................................................. 6

Troubleshooting ........................................................................................................... 9

Specifications .............................................................................................................. 9

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA) .............................. 11

Allen-Bradley PLCs

4SLC 5/01™ and SLC 5/02™ Modular Processors

Publication 1747-IN011B-MU-P - July 2002

Important User Information

Because of the variety of uses for the products described in this publication, those

responsible for the application and use of this control equipment must satisfy

themselves that all necessary steps have been taken to assure that each application

and use meets all performance and safety requirements, including any applicable

laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this guide

are intended solely for purposes of example. Since there are many variables and

requirements associated with any particular installation, Allen-Bradley does not

assume responsibility or liability (to include intellectual property liability) for actual

use based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,

Installation, and Maintenance of Solid-State Control (available from your local

Allen-Bradley office), describes some important differences between solid-state

equipment and electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part,

without written permission of Allen-Bradley Company, Inc., is prohibited.

Throughout these installation instructions we use notes to make you aware of

safety considerations:

Attention statements help you to:

•identify a hazard

•avoid the hazard

•recognize the consequences

ATTENTION

Identifies information about practices or circumstances that can

lead to personal injury or death, property damage or economic

loss

IMPORTANT Identifies information that is critical for successful application

and understanding of the product.

SLC 5/01™ and SLC 5/02™ Modular Processors 5

Publication 1747-IN011B-MU-P - July 2002

For More Information

If you would like a manual, you can:

•download a free electronic version from the internet:

www.theautomationbookstore.com

•purchase a printed manual by:

–contacting your local distributor or Rockwell Automation representative

–visiting www.theautomationbookstore.com and placing your order

–calling 1.800.963.9548 (USA/Canada) or

001.330.725.1574 (Outside USA/Canada)

Required Tools and Equipment

•medium blade screwdriver

•programming equipment

•a 1747-PIC, 1784-KTX, or 1784-PCMK communication interfaces

Safety Considerations

For Refer to this Document Pub. No.

A more detailed description on how to install

and use your modular SLC 500 system. SLC 500 Modular Hardware

Style User Manual 1747-UM011

A reference manual that contains status file

data, instruction set, and troubleshooting

information.

SLC 500 Instruction Set

Reference Manual 1747-RM001

ATTENTION

Never install, remove, or wire any module while power is

applied. Also, do not expose processor modules to surfaces or

other areas that may typically hold an electrostatic charge.

Electrostatic charges can alter or destroy memory.

Allen-Bradley PLCs

6SLC 5/01™ and SLC 5/02™ Modular Processors

Publication 1747-IN011B-MU-P - July 2002

For general recommendations concerning installation safety requirements and

safety related work practices, refer to the requirements specific to your region.

•Europe: Reference the standards found in EN 60204 and your national

regulations.

•United States: refer to NFPA 70E, Electrical Safety Requirements for Employee

Workplaces.

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or

non-hazardous locations only. The following WARNING statement applies to use in

hazardous locations.

Installation Procedure

Install the Battery

IMPORTANT See page 11 for information on proper battery handling,

storage, and transporting.

WARNING

EXPLOSION HAZARD

•Substitution of components may impair suitability for Class

I, Division 2.

•Do not replace components or disconnect equipment

unless power has been switched off or the area is known to

be non-hazardous.

•Do not connect or disconnect components unless power

has been switched off or the area is known to be

non-hazardous.

•All wiring must comply with N.E.C. article 501-4(b).

IMPORTANT If your processor has a battery— the battery is an option for the

SLC 5/01 (1747-L511) processor — make sure it is connected

before installing your processor into the chassis. This provides

memory backup for your processor should the controller power

supply fail.

SLC 5/01™ and SLC 5/02™ Modular Processors 7

Publication 1747-IN011B-MU-P - July 2002

1. Open the door of the processor.

2. Remove the jumper from the battery connector socket. Store the jumper in a

safe place for possible future use without the battery.

3. Insert a new or replacement battery in the holder making sure it is held in by

the retainer clips.

4. Plug the battery connector into the socket. See the figure below.

5. Close the processor door.

Install the Processor

Make sure system power is off; then insert the processor into slot 0 of the 1746

chassis.

IMPORTANT See page 11 for information on proper battery handling,

storage, and transporting.

IMPORTANT The SLC 500 Modular Processors must be inserted into the left

slot (slot 0), as shown below. In addition, remove the

protective wrap after installing the processor.

White

Lead

Red

Lead

Battery

Connector

Retainer

Clips

Allen-Bradley PLCs

8SLC 5/01™ and SLC 5/02™ Modular Processors

Publication 1747-IN011B-MU-P - July 2002

Apply Power to the Processor

1. Energize the chassis power supply.

2. Check the chassis power supply and processor LEDs. The power LED on

the power supply should be on and the fault LED on the processor should

be flashing.

Load Your Software

Refer to your programming software documentation.

Processor

Release

Card Guide

Protective Wrap

Power

Supply

Indicates the LED is OFF.

Indicates the LED is ON.

Indicates the LED is FLASHING.

Status of LED does not matter.

POWER RUN

CPU FAULT

FORCED I/O

BATTERY LOW

COMM

The RUN LED onthe SLC 5/01 processor is

actully labeled “PC RUN.” Also, the SLC

5/01 processor does not have a COMM

LED.

SLC 5/01™ and SLC 5/02™ Modular Processors 9

Publication 1747-IN011B-MU-P - July 2002

Establish Communications with the Processor

1. Connect the 1747-PIC to the processor and your personal computer.

2. Set the communication parameters of the software to match the default

parameters of the processor:

–DH-485

–19.2k baud

–Node Address = 1

Troubleshooting

Before troubleshooting your SLC 500 system, please obtain an SLC 500 Modular

Hardware Style User Manual (1747-UM011) from one of the sources listed on page

5. Refer to the chapter on Troubleshooting.

In addition to the SLC 500 Modular Hardware Style User Manual, the SLC 500

Instruction Set Reference Manual (1747-RM001) may also be obtained from the

sources listed on page 5. This manual contains explanations and examples for the

entire instruction set as well as for all status words and bits. It also contains

explanations for all possible fault codes found in status word S:6.

Specifications

Specification SLC 5/01

(1747-L511, -L514) SLC 5/02

(1747-L524)

Program Memory 1K or 4K Instructions 4K Instructions

Additional Data Storage 0 0

Maximum I/O Capacity 3940 discrete inputs

3940 discrete outputs 4096 discrete inputs

4096 discrete outputs

Max. Local Chassis/Slots 3/30 3/30

Programming Software RSLogix 500™, PLC–500 A.I. Series™, APS, and HHT

Programming Instructions 52 71

Typical Scan Time(1)

(1) The scan times are typical for a 1K ladder logic program consisting of simple ladder logic and

communication servicing. Actual scan times depend on your program size, instuctions used, and the

communication protocol.

8 ms/K 4.8 ms/K

Bit Execution (XIC) 4 µs 2.4 µs

Allen-Bradley PLCs

10 SLC 5/01™ and SLC 5/02™ Modular Processors

Publication 1747-IN011B-MU-P - July 2002

The following table summarizes the available memory back up options for the SLC

5/01 and SLC 5/02 processors. EEPROM memory modules provide non-volatile

memory back-up.

Communication Receive Receive or Initiate

DH-485 SLC 5/01(1)

(1) A 1747-PIC is required when connecting to the DH-485 channel for programming.

SLC 5/02(1)

Description Specification

Power Supply Loading at 5V dc 350 mA

Power Supply Loading at 24V dc 105 mA

Program Scan Hold-up Time after Loss of Power 20 ms to 3 s (dependent on power supply loading)

Noise Immunity NEMA Standard ICS 2-230

Vibration Displacement: 0.015 inch, peak-to-peak at 5-57 Hz

Acceleration: 2.5Gs at 57-2000 Hz

Shock (operating) 30Gs

Ambient Temperature Rating Operating: 0 to + 60°C (32°F to 140°F)

Storage: 40°C to 85°C (-40°F to 185°F)

Humidity 5 to 95% without condensation

Agency Certification UL listed

CSA approved

Class 1, Groups A, B, C or D, Division 2

CE compliant for all applicable directives

C-Tick marked for all applicable acts

SLC 5/01

(1747-L511/1747-L514) SLC 5/02

(1747-L524)

1747-M1, 1747-M2 1747-M2

Otros manuales para SLC 5/01

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Hardware de computadora de Allen-Bradley

Allen-Bradley

Allen-Bradley SLC 5/03 Manual de usuario

Allen-Bradley

Allen-Bradley 2094-AL15S Manual de usuario

Allen-Bradley

Allen-Bradley 2707-MVH232 Manual de usuario

Allen-Bradley

Allen-Bradley SLC 5/01 Manual de usuario

Allen-Bradley

Allen-Bradley 1771-SF1 Manual de usuario

Allen-Bradley

Allen-Bradley SLC 5/04 Manual de usuario

Allen-Bradley

Allen-Bradley 1747-DCM Manual de usuario

Allen-Bradley

Allen-Bradley Mini-PLC Mini-PLC-2/16 Manual de usuario

Allen-Bradley

Allen-Bradley SLC 5/03 Manual de usuario

Allen-Bradley

Allen-Bradley SLC 500 Series Manual de usuario

Allen-Bradley

Allen-Bradley PLC-5 MAP/OSI Manual de usuario

Allen-Bradley

Allen-Bradley 2707 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario