Alcatel OAW-LC-2G24F Manual de usuario
Alcatel OmniAccess 6000 OAW-LC-2G24F Installation Instructions 1
Alcatel OmniAccess 6000
OAW-LC-2G24F
Installation Instructions
These instructions explain how to install an Alcatel 6000 Wireless
LAN switch line card (OAW-LC-2G24FE). The Alcatel 6000 Line
Card has 24 Fast Ethernet (FE) ports and two Gigabit Ethernet
(GE) ports.
The FE ports provide 10/100 Mbps Ethernet connections to APs
and wired LAN segments. No power or serial connectivity is
provided by the ports on this line card.
Physical Description
Module Fastening Screws
Module Handle
POWER
STATUS
LNK/
ACT
LNK/
ACT
LNK/
ACT
0
1
POE 10 12
24
22
23
ACCESS POINT STATUS
0 2 4 6 810121416182022
1 3 5 7 911131517192123
25
0 2 4 6 8 10 121416182022
24 25
1 3 5 7 9 11 131517192123
11
4 5
2
6
3
1
2
OmniAccess 6000 LC-2G24F Installation Notes: Installation Guide
2Part 031658-00 May 2005
This handle is used for removing or inserting the module into the switch
chassis.
24 FE Ports
These ports are used to connect APs and wired LAN segments to the Alcatel
Wireless LAN Switch. These ports provide 10/100 Mbps Ethernet connectivity,
and in some cases, power and serial connectivity as well. See “Port and Cable
Specifications” for more information.
LNK/ACT LED
Each FE port has its own LNK/ACT LED, located at the left side of the port.
During operation, these LEDs provide the following status information:
Module Indicator LEDs
Power LED
This LED lights green when the line card is properly installed and the system is
powered up.
Status LED
During operation, the Status LED provides the following information:
CAUTION—Do not use the line card handle to lift or move the Alcatel
Wireless LAN Switch. Serious damage could result.
TABLE 1 FE LNK/ACT LED
Status Description
Off No Ethernet link on the port.
Green An Ethernet link has been established on the port, but no
data is currently being transmitted or received.
Flashing
Green
The port is transmitting or receiving data. The flashing
rate is proportional to your network activity.
Amber The Ethernet link on the port is encountering errors.
TABLE 2 Line Card Status LED
Status Description
Off The line card is powered off or initializing.
Green The line card is operating properly.
Amber The line card is being initialized.
Red The line card has failed.
3
4
A
B
Alcatel OmniAccess 6000 OAW-LC-2G24F Installation Instructions 3
Access Point Status LEDs
Each LED represents the status of APs connected to a specific port on the
switch. During operation, the LEDs provide the following information:
The LED states listed above are listed in order of precedence (highest to
lowest). If more than one AP is connected to the port, the state with the
highest precedence is displayed.
2 GE ports
Each GE port has its own LNK/ACT LED, located to the right of the port.
During operation, these LEDs provide the following status information:
TABLE 3 Line Card AP Status LED
Status Description
Red (solid) An AP on this port has failed (highest precedence).
Red (flashing) An air monitor on this port has detected an unsecured AP.
The AP is attached to your network but is not listed in the
switch security policies. If security policies are enabled,
clients are not granted access to your network through the
unsecured AP.
Green
(flashing)
An air monitor on this port has detected interference. The
interfering device (AP or other radio source) has been
detected by your valid APs, but has no wired presence on
your network.
Amber (solid) Load balancing is enabled on this port or an AP has reached
the maximum number of clients it is configured to support.
Green (solid) All detected APs on this port are operating as expected.
Off No AP is detected on the port (lowest precedence)
TABLE 4 GE LNK/ACT LED
Status Description
Off No Ethernet link on the port.
Green An Ethernet link has been established on the port, but no
data is currently being transmitted or received.
Flashing
Green
The port is transmitting or receiving data. The flashing rate is
proportional to your network activity.
Amber The Ethernet link on the port is encountering errors.
5
6
OmniAccess 6000 LC-2G24F Installation Notes: Installation Guide
4Part 031658-00 May 2005
Inserting a Line Card
The line card is hot-swappable and can be inserted into the Alcatel Wireless
LAN Switch chassis while system power is on or off. However, removing a line
card on a live switch is service affecting and all traffic processing will stop until
the replacement line card is installed and operating.
Make sure you understand the procedure and all precautions.
Before beginning, read the entire procedure. Make sure you understand all the
precautions in these installation instructions.
Prepare the slot.
The first line card should be installed in Slot 2 of the Alcatel Wireless LAN
Switch chassis. A second optional line card can be installed in Slot 3, and a
third in Slot 1. A line card cannot be installed in Slot 0.
If you are replacing a previously installed module, first see “Removing a Line
Card”.
To install a module in a previously empty bay, remove the blank cover plate
first. To do this, use a #2 Phillips or cross-head screwdriver to loosen both of
the fastening screws on the blank cover place. The screws loosen with
counter-clockwise rotation, but are captive and cannot be fully removed.
Carefully insert the line card into the chassis slot.
Hold the line card by the handle. Align the rear of the card with the guide-rails
in the chassis slot and gently slide the module toward the backplane. Do not
force the module; it should slide in easily most of the way.
CAUTION—This procedure should be performed only by a trained
technician.
CAUTION—Be sure to exercise proper Electrostatic Discharge (ESD) pre-
cautions when handling components.
CAUTION—If installing a line card in Slot 1, make sure that the fastening
screws for the module in the slot above it are fully secured. If the
module in Slot 3 is loose, it could interfere with the new module
insertion and possibly damage the components.
1
2
3
Alcatel OmniAccess 6000 OAW-LC-2G24F Installation Instructions 5
Engage the line card.
There may be moderate resistance when the line card meets the connectors in
the backplane. Press firmly so that the connectors at the back of the module
engage with the backplane, but do not use excessive force.
If the system is powered up, the module’s Power LED will light up green if the
line card is inserted properly.
Secure the line card.
Use a #2 Phillips or cross-head screwdriver to push in the captive fastening
screws and turn them clockwise until moderate resistance is felt. Do not
over-tighten.
Connect the appropriate network cables.
Removing a Line Card
The line card is hot-swappable and can be inserted into the Alcatel Wireless
LAN Switch chassis while system power is on or off. However, removing a
line card on a live switch is service affecting and all traffic processing will stop
until the replacement line card is installed and operating.
Make sure you understand the procedure and all precautions.
Before beginning, read the entire procedure. Make sure you understand all the
precautions in these installation instructions.
Disconnect all cables attached to the line card.
Loosen the module’s fastening screws.
At the front of the Alcatel Wireless LAN Switch, use a #2 Phillips or
cross-head screwdriver to loosen both of the fastening screws on the
faceplate of the installed line card. The screws loosen with counter-clockwise
rotation, but are captive and cannot be fully removed.
Remove the line card.
4
5
6
CAUTION—This procedure should be performed only by a trained
technician.
CAUTION—If removing a line card from Slot 1, make sure that the
fastening screws for the module in the slot above it are fully secured.
If the module in Slot 3 is loose, it could interfere with the module
removal and possibly damage the components.
1
2
3
4
OmniAccess 6000 LC-2G24F Installation Notes: Installation Guide
6Part 031658-00 May 2005
Grasp the module handle firmly and draw the line card forward from its slot.
There may be moderate resistance as the module comes free from its
connections with the chassis backplane, but do not use excessive force. Once
disengaged from the backplane, the line card should easily slide out the rest of
the way.
Cover blank slots.
For safety considerations, as well as to promote proper airflow for cooling and
to prevent dust from entering the switch chassis, cover any unoccupied slot
with a blank cover plate.
Port and Cable Specifications
FE Port
The FE port provides a 10/100 Mbps Ethernet connection. The RJ-45 female
connector port pin-outs are shown below:
The port accepts a 4- or 8-conductor Category 5 UTP Ethernet cable with an
RJ-45 male connector. A straight-through cable is required for connection to a
network port. A crossover cable is required for connection to a management
workstation.
For cables that run through plenums or air-handling spaces as described in
NEC (2002) Article 300.22(C), the cable should be suitable under NEC Article
800.50 and marked accordingly for use in plenums and air-handling spaces
with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP. Be sure
to install cables in accordance with all applicable local regulations and
practices.
5
10/100 Mbps Ethernet RJ-45 Female
Pin-Out
*POE optional
**Serial optional
Serial TxD** (POE positive*)
Serial TGND** (POE positive*)
Serial RxD** (POE negative*)
Serial RGND** (POE negative*)
1
2
3
4
5
6
7
8
ETH Rx+ (POE negative*)
ETH Rx– (POE negative*)
ETH Tx+ (POE positive*)
ETH Tx– (POE positive*)
Direction
Input
Output
Alcatel OmniAccess 6000 OAW-LC-2G24F Installation Instructions 7
Contacting Alcatel
Web Site
Telephone Numbers
zMain Site http://www.alcatel.com
zSupport http://www.alcatel.com/enterprise
zMain US/Canada (800) 995-2612
zMain Outside US (818) 880-3500
OmniAccess 6000 LC-2G24F Installation Notes: Installation Guide
8Part 031658-00 May 2005
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Alcatel
Alcatel
Alcatel OS6855-24 Manual de instalación
Alcatel
Alcatel OS6850-P48 Manual de usuario
Alcatel
Alcatel OmniPCX 4400 Manual de usuario
Alcatel
Alcatel OmniStack 6124 Manual de usuario
Alcatel
Alcatel OmniSwitch 6800 Manual de instalación
Alcatel
Alcatel OmniSwitch 6600 Family Manual de usuario
Alcatel
Alcatel 1850 TSS-320 Nota de versión
Alcatel
Alcatel OmniAccess 4308 Manual de usuario
Alcatel
Alcatel OmniStack 6300-24 Manual de usuario
Alcatel
Alcatel omniaccess 4302 Manual de usuario
Alcatel
Alcatel OmniStack 4024 Manual de usuario
Alcatel
Alcatel Alcatel OmniAccess 4324 Manual de usuario
Alcatel
Alcatel 7750 SR-7 Manual de usuario
Alcatel
Alcatel OmniStack 6148 Manual de usuario
Alcatel
Alcatel OmniSwitch 6800 Manual de usuario
Alcatel
Alcatel OmniAccess AP60 Manual de usuario
Alcatel
Alcatel OmniSwitch 6600 Family Manual de usuario
Alcatel
Alcatel OmniStack LS 6248 Manual de usuario
Alcatel
Alcatel OmniSwitch 9000 Manual de usuario
Alcatel
Alcatel LinkHub HH70VH Manual de usuario
