Alcatel OS-6124 Manual de usuario

Part No. 060143-10, Rev. A

January 2002

OmniStack®6124

Getting Started Guide

An Alcatel service agreement brings your company the assurance of 7x24 no-excuses

technical support. You’ll also receive regular software updates to maintain and

maximize your Alcatel product’s features and functionality and on-site hardware

replacement through our global network of highly qualified service delivery partners.

Additionally, with 24-hour-a-day access to Alcatel’s Service and Support web page,

you’ll be able to view and update any case (open or closed) that you have reported to

Alcatel’s technical support, open a new case or access helpful release notes, technical

bulletins, and manuals. For more information on Alcatel’s Service Programs, see our

web page at www.ind.alcatel.com, call us at 1-800-995-2696, or email us at

[email protected].com.

This Manual documents OmniStack 6124 hardware and software.

The functionality described in this Manual is subject to change without notice.

reproduced in whole or in part without the express written permission of Alcatel Internetworking,

Inc.

Alcatel®and the Alcatel logo are registered trademarks of Compagnie Financiére Alcatel, Paris,

France. OmniSwitch®and OmniStack®are registered trademarks of Alcatel Internetworking, Inc.

Omni Switch/Router™, SwitchExpertSM, the Xylan logo are trademarks of Alcatel Internetworking,

Inc. All other brand and product names are trademarks of their respective companies.

26801 West Agoura Road

Calabasas, CA 91301

(818) 880-3500 FAX (818) 880-3505

info@ind.alcatel.com

US Customer Support-(800) 995-2696

International Customer Support-(818) 878-4507

Internet-http://www.ind.alcatel.com

Warning

This equipment has been tested and found to comply with the limits for Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions in

this guide, may cause interference to radio communications. Operation of this equipment

in a residential area is likely to cause interference, in which case the user will be required

to correct the interference at his own expense.

The user is cautioned that changes and modifications made to the equipment without

approval of the manufacturer could void the user’s authority to operate this equipment.

It is suggested that the user use only shielded and grounded cables to ensure compliance

with FCC Rules.

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the radio interference regulations of the Canadian

department of communications.

Le present appareil numerique níemet pas de bruits radioelectriques depassant les

limites applicables aux appareils numeriques de la Class A prescrites dans le reglement

sur le brouillage radioelectrique edicte par le ministere des communications du Canada.

Contents

Introduction 1

Installing the Switch 2

Package Contents 2

Description of Hardware 2

Mounting the Switch 3

Stacking Switches on a Flat Surface 3

Mounting Switches in a Rack 4

Installing a Management Module 4

Installing Optional Media and Stacking Modules 5

Connecting Stacking Modules across Multiple Switches 5

Installing a GBIC Transceiver 6

Connecting the Switch System 7

Making a Connection to an RJ-45 Port 7

Connecting to a 100BASE-FX Port 8

Connecting to a Gigabit Fiber Optic Port 8

Connecting to a 1000BASE-T Port 9

Powering On the Switch 10

Verifying Port Status 10

Verifying System Operation 11

Applications 11

Product Specifications 13

Base Unit 13

Physical Characteristics 13

Switching Criteria 13

Traffic Control 13

Modules 14

Management Module (OS-6124-MNGT-KIT) 14

100BASE-FX Module (OS-6ESM-100FM-2) 14

1000BASE-T Module (OS-6GSM-T-1) 14

1000BASE-SX Module (OS-6GSM-FM-1) 14

1000BASE-LX Module (OS-6GSM-FS-1) 15

GBIC Module (OS-6GSM-GBIC-1) 15

Stacking Module (OS-6STK-KIT) 15

Redundant Stacking Module (OS-6100-RST-KIT) 15

Troubleshooting 15

Diagnosing Switch Indicators 15

Power and Cooling Problems 16

Installation 16

Contents

Port and Cable Assignments 17

RJ-45 Port Description 17

Straight-Through Wiring 17

Crossover Wiring 17

1000BASE-T Pin Assignments 18

1000BASE-T Cable Requirements 18

Cable Testing for Existing Category 5 Cable 18

Adjusting Existing Category 5 Cabling 18

EMI Certification 19

FCC Class A Certification (USA) 19

Canada Department of Communications - Class A 19

BSMI Class A (Taiwan) 19

VCCI Class A Compliance (Japan) 19

CE Mark Declaration of Conformance for EMI and Safety (EEC) 20

Safety Compliance 21

Warning: Fiber Optic Port Safety 21

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique 21

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit 21

Underwriters Laboratories Inc. (USA) 21

Wichtige Sicherheitshinweise (Germany) 22

Optional Hardware 22

Introduction

The Alcatel OmniStack®6124 is perfect for moving workgroups from conventional

10 Mbps Ethernet to multiple-segment 100 Mbps Fast Ethernet, and for

consolidating your network equipment into a single, clean, efficient, and super-fast

switch stack. This switch system delivers dedicated 100 Mbps links to each attached

LAN segment (independent collision domain) or to any PC attached directly to the

stack – all with conventional cabling and adapters. It completely eliminates the

bottlenecks of shared 10 Mbps Ethernet networks by providing a wide bandwidth of

up to 8.8 Gbps per switch, and a stack backplane that can operate at up to

9.6 Gbps. This makes it ideal for increasing the throughput of interconnected

Ethernet and Fast Ethernet hubs or server farms.

This switch includes three slots on the rear panel for various modules:

• The upper slot is for an SNMP/RMON Management Module. The stack supports one

master and one backup management agent.

• The lower right slot is for optional media expansion modules, including a dual-port

100 Mbps fiber optic module that can be connected to a remote site up to

2 kilometers (1.24 miles) away, or a single-port Gigabit module that can be used to

uplink to a collapsed Gigabit backbone or for a high-speed server connection.

• The lower left slot is for either an optional media expansion module or Stacking

Module. (Up to six switch units can be stacked together using Stacking Modules.)

When the Management Module is installed, this system can provide a wide array of

advanced features:

• Master agent module manages entire stack in-band or out-of-band

• Backup agent module provides fault tolerance

• A fault-tolerant closed-loop stack architecture is supported with a Redundant

Stacking Module

• Supports Telnet, SNMP/RMON and Web-based interface

• Four-group RMON (including Statistics, History, Alarms and Events)

• Spanning Tree Algorithm for redundant paths between switches

• VLAN support for up to 256 groups, port-based or with 802.1Q VLAN tagging

• GVRP for automatic VLAN learning*

• IGMP multicast filtering

• Quality of Service supports two levels of priority with Weighted Fair Queueing

• Configurable broadcast storm control

• Port mirroring (for real-time debugging without affecting the target port)

• Port trunking (up to 5 trunks per switch or 12 trunks for the entire stack, each trunk

contains 2~4 ports)

* This feature is not supported in the current firmware release.

The Management Module allows you to configure or monitor the switch using the

embedded

management program or SNMP/RMON applications. To manage the

switch, you can

make a direct connection to the console port. You can also make a

network connection to manage the switch using Telnet, the on-board Web agent, or

any SNMP-based network management software.

OmniStack®6124

Installing the Switch

Before installing the switch verify that you have all the items listed under “Package

Contents.” If any of the items are missing or damaged, contact your local Alcatel

distributor. Also be sure you have all the necessary tools and cabling before

installing the switch. Note that this switch can be installed on any suitably large flat

surface or in a standard EIA 19-inch rack. After installing the switch, refer to the

Users Guide to set up its more advanced features, such as Spanning Tree Protocol

or VLAN port groups.

Package Contents

This package includes:

Description of Hardware

The base unit contains 24 10BASE-T/100BASE-TX ports, plus three slots on the

rear panel for various modules. A Management Module can be installed in the upper

slot on the rear panel (see page 3). The lower-left slot can be used for an optional

media expansion module or Stacking Module, while the lower-right slot can be used

for a media expansion module. Note that the media expansion modules include a

Fast Ethernet fiber optic module with two 100BASE-FX (SC type) ports or a one port

Gigabit 1000BASE-SX (SC type), 1000BASE-LX, 1000BASE-T, or GBIC uplink

module.

All RJ-45 ports on the base unit operate at 10 or 100 Mbps, and support

auto-negotiation of speed, duplex mode (i.e., half or full duplex), and flow control.

The 1000BASE-SX and 1000BASE-LX ports are fixed at 1000 Mbps but

auto-negotiate duplex mode. The 1000BASE-T auto-negotiates duplex mode and

auto-senses speed to 10/100/1000 Mbps. The 100BASE-FX module is fixed at the

100 Mbps, full duplex. All media types can auto-negotiate flow control.

Note that when using auto-negotiation, the speed, transmission mode and flow

control can be automatically set if this feature is also supported by the attached

device. Otherwise, these items can be manually configured for any connection.

The base unit also includes a display panel for key system and port indications that

simplify installation and network troubleshooting.

OmniStack®6124

• Four rubber foot pads • This Getting Started Guide

• Rack mount bracket kit • Release Notes

• AC power cord • Owner registration card

OmniStack®6124 Management Module Kit

• Management Module • This Getting Started Guide

• Console cable • Release Notes

• User Guide • Owner registration card

Installing the Switch

The following figure shows the components of this switch system:

Mounting the Switch

This switch can be placed directly on your desktop, or mounted in a rack.

Before you start installing the switch, make sure you can provide the right operating

environment, including power requirements, sufficient physical space, and proximity

to other network devices that are to be connected. Verify the following installation

requirements:

• Power requirements: 100 to 240 VAC (± 10%) at 50 to 60 Hz (± 3 Hz). The switch’s

power supply automatically adjusts to the input voltage level.

• The switch should be located in a cool dry place, with at least 10 cm (4 in.) of space

on the sides for ventilation.

• Place the switch out of direct sunlight, and away from heat sources or areas with a

high amount of electromagnetic interference.

• If you intend to mount the switch in a rack, make sure you have all the necessary

mounting screws, brackets, bolts and nuts, and the right tools.

• Check if network cables and connectors needed for installation are available.

Stacking Switches on a Flat Surface

The OmniStack®6124 can be stacked

anywhere there is enough flat space, such

as on a table or desktop.

1. Stick the self-adhesive rubber foot

pads (that come with this package) on

each of the 4 concave spaces located

on the bottom of the first switch.

2. Place the first switch on a firm flat surface where you want to install the stack.

3. Repeat step 1 for each switch before stacking them. The switch’s rubber foot

pads cushion the switch against shock/vibrations and provide space between

each switch for ventilation.

DC INPUT

3.3 15

12 0.7

100-240V~ 50-60Hz 2A

stacking module can be installed in module 2 only

Module 2 Module 1

MNGT

Port Status

Indicators

10/100 Mbps

RJ-45 Ports

Power

Socket RPU

Connector

Module

Indicators Mode

Selection System

Indicators

Media or Stacking

Module Slot Media

Module Slot Management

Module Slot

OmniStack®6124

Mounting Switches in a Rack

Please comply with the following instructions to ensure that your switch is securely

mounted in the rack.

1. Use a standard EIA 19-inch rack.

2. Position the switch in the rack by lining up

the holes in the attached brackets with the

appropriate holes on the rack, and then

use the rack-mount screws to mount the

switch in the rack.

Installing a Management Module

One Management Module is required to manage all of the switches in the stack. One

other backup Management Module may also be installed in the stack to provide fault

tolerance. A Management Module only installs in a switch’s rear-panel upper slot, do

not try to install it in either of the two lower slots.

If you install a backup Management Module, it will automatically take over from the

master should it fail. The switch with the lowest stack unit ID will always act as the

master agent. For more information on switch management and the fail-over

process, see the OS-6124 Users Guide.

Note: A Management Module may be installed in any unit in the stack, but it is

suggested that the module be installed in the switch with the stack unit ID of “1.” In

a stack with no “closed-loop” (see “Connecting Stacking Modules across Multiple

Switches” on page 5), unit ID 1 will be the switch without a connection on the

Stacking Modules “UP” port. For a closed-loop stack, unit ID 1 will be the switch

that has the Redundant Stacking Module installed.

You can install a Management Module as described below:

1. Disconnect power to the switch (the modules are not hot-swappable).

2. Remove the face plate on the switch’s upper slot by removing the two screws

with a flat-head screwdriver.

3. Before opening the package that contains the module, touch the bag to the

switch casing to discharge any potential static electricity.

4. Remove the module from the anti-static shielded bag.

5. Holding the module level, gently push it all the way into the slot along the guide

rails, ensuring that it firmly engages with the connector.

6. If you are sure the module is properly mated with the connector, tighten the

retainer screws to secure the module in the slot.

Caution: The slide-in modules are not hot-swappable. Be sure you power off the switch

before installing any of these modules.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Alcatel

Alcatel

Alcatel SPEED TOUCH 570 Manual de instrucciones

Alcatel

Alcatel SpeedTouch 570 Guía de seguridad

Alcatel

Alcatel SPEED TOUCH PRO Manual de usuario

Alcatel

Alcatel LINKZONE 2 Manual de usuario

Alcatel

Alcatel Speed Touch 591s Manual de usuario

Alcatel

Alcatel Router Manual de usuario

Alcatel

Alcatel one touch Home H850 Manual de usuario

Alcatel

Alcatel OmniStack OS-LS-6248 Manual de usuario

Alcatel

Alcatel OmniSwitch 8800 Manual de instalación

Alcatel

Alcatel OS6602-24 Manual de usuario

Alcatel

Alcatel LINKHUB HH71V1 Manual de usuario

Alcatel

Alcatel Omni Switch/Router Manual de usuario

Alcatel

Alcatel Speed Touch Wireless Manual de usuario

Alcatel

Alcatel SPEEDTOUCH 710 Manual de usuario

Alcatel

Alcatel Omni Switch/Router Manual de usuario

Alcatel

Alcatel SpeedTouch 510 Manual de usuario

Alcatel

Alcatel OmniStack OS-LS-6224 Manual de usuario

Alcatel

Alcatel AST570 Manual de usuario

Alcatel

Alcatel Speed Touch Home Manual de usuario

Alcatel

Alcatel SPEED TOUCH PRO Manual de usuario

Alcatel

Alcatel Y850 Manual de usuario

Alcatel

Alcatel LINKZONE Manual de usuario

Alcatel

Alcatel 7750 SR-12 Manual de usuario

Alcatel

Alcatel OS6850-48L Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad